EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

GLEFM397DBA Frigidaire Range - Instructions

All Instructions for the GLEFM397DBA
46 - 60 of 110

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
NO HEAT IN UPPER ELEMENT
2 of 2 people found this instruction helpful.
  • Jerome from WOOD LAKE, MN
  • Really Easy
  • 30 - 60 mins
  • Socket set
NEED A QUARTER INCH SOCKET FOR THE BOLTS. REMOVE THE BACK PANEL AND THEN YOU WILL SEE THE TWO ELECTRIC WIRES GOING TO THE TERMINALS OF THE ELEMENT. DISCONNECT AND THEN GO TO THE FRONT OF OVEN AND REMOVE THE FOUR BOLTS THAT HOLD IN THE TOP ELEMENT. SIMPLY, VERY SLOWLY PULL THE ELEMENT FORWARD UNTILL IT CLEARS THE BACK AND YOUR GOOD TO GO. DO NOT FORGET TO DISCONNECT THE POWER TO THE OVEN BEFORE YOU START!
Was this helpful?
Thank you for voting!
lens was broken
2 of 3 people found this instruction helpful.
  • Kenneth from Coeur d'Alene, ID
  • Really Easy
  • Less than 15 mins
after pulling away from wall and unplugging remove 5 screws in upper back panel lift off being careful of sharp edges if part of lens is still in hole push it out towards the front insert lens from front of unit slide light assy over pin on back of lens replace back panel plug in range push back against wall check for level you're done
Was this helpful?
Thank you for voting!
Element burned out
2 of 3 people found this instruction helpful.
  • Jeff from BELLEVUE, WA
  • Difficult
  • More than 2 hours
  • Pliers, Screw drivers
The original instructions were to replace burner and plug wires back in the same plug they came from.
The problem is that the plug order had changed between parts.
Use a pencil to highligt the plug numbers on both new and old plugset, to fint the new plug positions. And need to reorient one of the burners to allow existing wir es to reach.
Was this helpful?
Thank you for voting!
Replace oven element
1 person found this instruction helpful.
  • Connie from BARTLESVILLE, OK
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Watched the included video and duplicated.
Was this helpful?
Thank you for voting!
Old screws were damaged
1 person found this instruction helpful.
  • Miriam from BROOKLYN, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took out old screws and replaced with new
Was this helpful?
Thank you for voting!
. F3 error code
1 person found this instruction helpful.
  • Garry from New Haven, CT
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
I was getting an error code every time I turned my oven on. After a Google search I discovered it was a faulty oven temperature sensor. This website is awesome because it has a video showing how to install
Was this helpful?
Thank you for voting!
light bilb went out
2 of 6 people found this instruction helpful.
  • Denise from Landover, MD
  • Really Easy
  • Less than 15 mins
replaced it
Was this helpful?
Thank you for voting!
temp was not reading right
3 of 10 people found this instruction helpful.
  • santa from glassboro, NJ
  • Really Easy
  • Less than 15 mins
  • Nutdriver
remove back panel took out old part splice wire replaced
Was this helpful?
Thank you for voting!
Lens cover for oven light broke.
0 of 1 people found this instruction helpful.
  • Amy from Corona, CA
  • Really Easy
  • Less than 15 mins
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this helpful?
Thank you for voting!
Convection fan making noise
0 of 1 people found this instruction helpful.
  • Willis from Friendsville, TN
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Removed old fan and replaced with new fan. To replace fan, the over interior fan blade was removed, then the two slip on wires were removed from the old fan motor, then the three screws securing the old fan motor were removed. The process was reversed to install replacement fan
Was this helpful?
Thank you for voting!
Cracked inside glass
0 of 2 people found this instruction helpful.
  • patti from Greer, SC
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers
I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti
Was this helpful?
Thank you for voting!
Broken globe in oven and burnt out light bulb
0 of 5 people found this instruction helpful.
  • Sharon from Foley, AL
  • Really Easy
  • Less than 15 mins
Easy as 1-2-3
Other Parts Used:
Was this helpful?
Thank you for voting!
element quick working
1 of 9 people found this instruction helpful.
  • Kathy from Shepherd, MT
  • Easy
  • 15 - 30 mins
  • Screw drivers
Ordering the part was easy.
Was this helpful?
Thank you for voting!
Sensor probe was not sebding proper temp to themostat which regulate the 2 heating elements.
  • Grayson Crisis enter from Sherman, TX
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
This is a slide in oven fully contained not in a wall, or wood enclosure. I slid the unit out away from the wall unplugged the power cord, used the nut driver to remove a dozen screws, not all of them, you dont need to pull the top back plate off just unscrew the bottom 3-4 screws on the top plate to release the lower back cover plate and you see the probe wire and the insertion point/hole. I actually did not even need to pull the full back plate off but it makes the handling of all the tools and stripping easier. I wish they had just left the plug off of the new probe and had left the 2 loose ends of the 2 wires that had to be spliced, it would have saved 15 minutes just with that part. If you dont have a real splicer tool ya gotta be careful to not cut the wires themselves if you use a sharp knife. Just cut the new probe plug off and splice on the old plug from the bad sensor which obviously you have cut and strip as well as I did and then it fits nicely back together like it was ment to be. I put elect tape on the 2 splices, you could use small wire nuts or whatever you desire, but turn the exposed splices back away from each other and tape them to the insulated wire so no exposed wire is touching any metal then I wrapped the completed taped splices with about a 4x5 piece of aluminum foil to help deflect the residual heat coming from the oven when it is on. put the probe through the hole and placed the metal retainer back in place and re- mounted the back panel plate,cover, that was it problem solved. This entire problem was caused originally in this relatively new oven because people who have been using the oven were sitting heavy pots and pans on the oven door and the hinges were sprung. The door would not stay shut during cooking. I dont know how long this had been going on before I discovered the issue. Once I replaced the hinges ( parts select ) the uneven, wrong temp, extended cooking problem jumped up. I am certain it was related to the open door not shutting for several months. They were using a bungie cord to pull the door closed and not completely. At this point I feel very comfortable with using parts select for all my appliance parts and advice. The folks here at my facility think I am an Einstien but when you have parts select working with you in the background you can't go wrong. I asked a hundred questions and learned alot and saved the facility at least 400 dollars by doing it myself. Thanks to my new work buddy PARTS SELECT. I was really a bit apprehensive about the doors hinges they looked dangerous and might have been but the tech I spoke with at P.S. walked me through it on the phone and I read the blogs which are really helpfull SORRY THIS ONE IS SO LONG.
Was this helpful?
Thank you for voting!
burner would not heat up
  • MARGARET from MILFORD, PA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
simple, removed a few screw's, unplugged old burner, plugged in the new one. that was basically it. easy!
Was this helpful?
Thank you for voting!
All Instructions for the GLEFM397DBA
46 - 60 of 110