FEATHERLITE Trimmer - Parts

It is a genuine OEM sourced replacement screw that is specially produced for use with the handheld lawn and garden equipment. This screw is a standard hardware which has multiple applications depending on your unit, for correct location and uses make sure to check appropriate diagrams of your model. This hex socket head screw is made of durable, high-quality metal and it is sold individually.

This is a manufacturer approved replacement part used on gas trimmers. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. If the engine won\\\'t start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburetor. Pull the st...Read morearter rope. If the engine starts and then quickly dies, the carburetor is likely the problem. This assembly includes a metal body carburetor, rubber o-ring and a plastic lever. When replacing carburetor it is advised that you also replace carburetor gaskets to ensure proper air tight seal for optimum performance. You will need a screwdriver to perform this repair.

This is a genuine component which is supplied by the original manufacturer for Poulan, Jonsered and Weed Eater handheld trimmers. The spring is utilized to apply tension on the spool. Unfortunately, over time the spring may wear out and lose tension eventually requiring a replacement. This high-quality spring-return is made of durable met...Read moreal and is sold individually. Make sure to refer to the appropriate diagrams for your model to ensure the exact location and the proper installation of this hardware. A screwdriver will be needed to perform this repair.

This genuine manufacturer-sourced part is specially designed for use with handheld lawn and garden equipment. It is an important component which provides a tight seal between connected parts. If the gasket is worn, damaged or missing, this will provide an identical replacement for the original part that was installed on a new unit. To ens...Read moreure the correct repair procedure, check the diagrams for your model. Note, this high-quality gasket is made of durable material and is sold individually.

This genuine OEM sourced pore is specially produced for Poulan and Weed Eater gas powered string trimmers. This rope is part of the recoil starter mechanism that allows user to quickly and easily pull-start the engine. It is made from durable nylon material and it is sold individually. Please note that the handle grip is sold separately.

This is a genuine OEM sourced replacement part designed for use on Weed Eater and Poulan trimmers. It is mounted over the cutting head assembly to direct grass clippings away from the operator. This part is made from high quality plastic and it is sold individually. It is a complete assembly which includes the durable plastic shield and the hardware to secure it.

This part has been sourced from the original manufacturer to ensure a high level of quality. The gearbox assembly is intended to be used with trimmers from Weed Eater and Poulan. This is a pre-assembled gearbox that includes all the gears, bearings, and linkages. This part is used to connect the lower drive shaft and the cutting head asse...Read morembly and to allow the two parts to rotate in unison. This gearbox assembly is priced as a single item.

This is an authentic replacement part manufactured for use with trimmers. The throttle cable connects the throttle trigger and carburetor. The connections on either end of the cable can break, or the cable can kink causing it to break. Replacing a broken throttle cable is a good way to extend the life of the trimmer. The throttle cable is...Read more sold individually. Depending on the model trimmer the tools needed maybe a screwdriver, torx screwdriver, or hex key.

Genuine OEM replacement part, this part is sold individually. The purpose of the 530053241 Return Spring is to push the bump knob of the spool assembly back into its original position after you have bumped the trimmer to release more cutting line.

It is a genuine item that is supplied by the original equipment manufacturer for handheld lawn and garden equipment. The wrist pin retainer is an important component which helps to secure the piston pin. If the part is missing or is damaged, this will provide an identical replacement for the original component that was installed on a new ...Read moreunit. Note, this high-quality wrist pin retainer is made of durable metal and is sold as an individual item. Keep in mind, the pin is all sold separately. A screwdriver, a wrench set, and pliers will be needed to perform this repair. To ensure the correct replacement procedure, refer to the appropriate diagrams for your model.

The limiter cap is made of plastic and attaches to the carb adjust grommet. It is a genuine Poulan, Weed Eater, and Husqvarna replacement part used in compatible chain saws. This item is available as an individual replacement part. A screwdriver might be required during the replacement of this item. This part may become broken and will need to be replaced.