FEATHERLITE Trimmer - Parts

This is an OEM replacement part and is sold individually. Its purpose is to filter out dust and debris from contaminating the carburetor and engine. When replacing the filter you can open the package in comes in and put a bit of two cycle oil in the bag and let it absorb into the filter. Then remove it from the bag and squeeze it with a...Read more paper towel to remove the excess oil. This will aid the filter in filtering out the unwantables.

This flywheel is an authentic manufacturer replacement part for use with lawn and outdoor equipment. The flywheel is a heavy, circular disc that has magnets that create an electric charge sent to the spark plug to create the spark that ignites the fuel and air mixture in the engine. It is attached to the engine crankshaft by a key known a...Read mores a shear pin or flywheel key. This assembly is a critical component in the starting and running of your power equipment. Over time, the magnets on the flywheel will wear down, and the flywheel may chip and crack. A faulty flywheel will result in a loss of power, excessive shaking during use, and difficulty starting the equipment. Remove the flywheel using a flywheel puller. Position the new flywheel on the crankshaft and secure it with the retaining nut and flywheel key. This flywheel is sold as an individual replacement part.

This is an Original Manufacturer Approved replacement part. This part is made out of Foam and it is sold individually. The purpose of the filter is to keep dust and debris from contaminating the carburetor and engine. Once an Air filter becomes dirty, it constricts the flow of air to the engine so it will not run properly. Air Box and Air Box Cover are sold separately.

The Starter Spring is a metal spring used to restract the rope after you pull it to start the engine. Installation of this OEM part is rated as "Medium" difficulty and requires a screwdriver, nutdriver, and torx bit. The part is installed inside the recoil housing. If broken, the rope will not retract and the part must be replaced.

This metal ring in your engine, known as the piston ring, seals the gap between the piston and cylinder wall. It makes sure that the gases produced during combustion do not escape and that the engine maintains the pressure it needs to run. If the piston ring is damaged, oil can seep into the combustion chamber, causing your engine to exhi...Read morebit rough idling and your machine emit blue smoke. To switch out a defective piston ring, detach the old ring from the piston with a screwdriver. When installing the new ring, you may need to compress it to make it fit properly. Please be aware that this genuine OEM replacement part is bought individually. It is recommended that you replace all the piston rings in your machine at once, as they tend to wear down at the same rate. Carefully review your user manual to determine how many rings your machine needs before placing your order.

The chainsaw starter rope is a three-foot-long white rope that is approved by the original equipment manufacturer, and which wraps around the recoil pulley and is pulled to start the engine. Installation is rated as "Easy" by customers and requires a screw driver, pliers, and torx screwdriver. If the rope breaks it should be replaced. Ref...Read moreer to your make, model and diagram to ensure this rope is right for your machine.

This ignition module is a genuine OEM sourced item, it is not an aftermarket imitation. Ignition module supplies electric current to the spark plug. If the ignition coil is defective, the engine may not start. Please note, this assembly includes a metal ignition module with a rubberized wire and the spark plug boot. To complete this repair you will need a screwdriver.

This OEM spool cover is designed to protect your trimmer spool and keep it free from damage and debris. It securely holds the trimmer line in place, preventing it from unraveling while you operate the trimmer. The cover, made of plastic, is located at the bottom of the trimmer head. If the cover is broken, you may notice cracks, chips, or...Read more missing parts. This can result in tangled or improperly feeding trimmer line. Furthermore, exposing the spool and line increases the risk of damage and accelerates wear. You will not be able to trim evenly or precisely. Replacing a broken spool cover is a simple task that requires no tools. Just remove the old cover and snap the new one on. Please keep in mind that the spool cover is sold separately from the spool.

This is a genuine Craftsman part for use with Trimmers. The line tap knob releases the cutting line when you bump the knob on the ground while the spool is turning. The most common reason for replacing the bump knob is when bumping the knob against the ground no longer causes the spool to release more line. This part is sold individually....Read more The tool that you will need to replace the line tap knob is a flat-head screwdriver.

This is a genuine OEM sourced rebuild kit is designed for gas trimmers/blowers. This kit contains all the necessary parts to rebuild your carburetor. It includes: primer bulb, the float, needle, gaskets, seals needed to repair or refurbish a carburetor. Replacing these items you would need a screwdriver and pliers.

This is a standard hardware which has multiple applications based on your tool. It is sourced from original equipment manufacturer for use with a variety of power equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. Requires a hex key or an allen wrench to install or remove it.