FWT449GFS1 Frigidaire Washer - Instructions

Everything went great, except replacing the rubber seal, that was a little bit harder to put back in place. But other then that, went very well and easy to repair.

I removed the back cover after disconnecting the electric and shutting off the water. I then proceeded to disconnect the water lines and then removed the water inlet valve by removing the two screws holding it in place. Then I used pliers to remove the hose leading to the washer. After that I did everything in reverse and was back in business. The video was very helpful and it made me feel comfortable with the procedure. I now know a little more about washers. Thanks for the excellent information.

Remove the top cover and the doorlacth and unplug the old parts as simple as that

took off front an back panels-pushed half inch socket over pins and pulled them out with channel locks from opposite side of socket-need a piece of broom handle or something about 2 ft. long to tap pins back in to make installation easier

Removed 2 screws, removed broken catch, seated new catch in correct orientation, replaced & tightened the 2 screws. Total time 2 minuets tops. Took longer to get & put away the screw driver.

The entire process, from diagnosing the problem, ordering the part, and instalation was fantastic! I ordered the part Friday afternoon and had it at my door Saturday afternoon. I was so relieved to read the installation posts from other customers demonstrating how common this issue is and how easy it was to fix! I simply watched the installation video that was sent with my confirmation email. It is also conveniently located on your website. I had the new part installed in less than 30 minutes AND before my husband got home! Thank you Partselect.com!

After watching the video, it was easy to chage them out. Very satisfied with getting order quickly and helpful instructions. Pins came out just like the video, new ones went in with no problem. Washer acting normal again.

Unplug the unit and disconnect the water lines. Remove the rear and top panels of the washer housing. Remove the drive belt and pulley. Use caution when removing the pulley as it is cast aluminium and will crack fairly easily. Remove the 3 8mm hex screws securing the motor, remove the motor. Remove the brick counter weight. Next remove the lower drainage hose on the under side of the drum. Remove the front rubber seal, there is a metal ring clamp around it tucked behind it, just stretch the spring to remove. (do not be afraid of this step it was very simple to re-install. I tried to avoid this step initially and leave the drum inside the housing, this was extremely annoying as it is very difficult to access the drum fasteners.)Remove the two shock absorbers by squeezing the front of the plastic pins and pulling on the rear with pliers. The drum should be hanging by the springs, next unhook the springs and pull the drum out(I had a friend help with this, the drum is pretty heavy but is managable by yourself if needed) you may have to disconnect the small air hose that connects to the pressure switch in order to slide the drum out. With the drum out simply unscrew the 20 - 10mm fasteners with a drill and socket adapter/extensions. With all the fasteners out you can seperate the two halves and remove the metal wash drum by taping on the shaft with a rubber mallet (do not hit the shaft with a metal hammer, it will mushroom the end and you will have difficulty reinstalling it. Use a block of wood if you have too. Once the metal drum is removed slide the new rear housing over it and re-assemble the washer in reverse order. You can do it, this was easier than I expected

Super easy!!! Purchased part, arrived in 3 days ... Use plyers to grab hold of the inner ring that was left in place when knob came off... Pushed in to off position, Turned counter clockwise! Like unscrewing a bottle... That's it! Unscrew all the way out and screw new timer knob assembly in, and your in business. Took less than 2 min.

Put the front up on a 4 X4 block. Removed the two screws at the bottom of the front panel. Slid the front panel down and off. With pliers squeezed the spring clamp and removed the hose, slid the hose out of the machine. Slid in the new hose into the hole in the back, put the spring clamp on the hose, slid the pump end of the hose onto the pump and using pliers put the spring clamp back on. Put the front panel back on and the screws, removed the block. Tested the washer.

In the video sent it showed how to replace the shocks with only removing the lower front panel. I found it was easier to also remove the back panel. There are more screws but it provided open access to the pins that needed to be removed. The parts went in easily and when compared to the original equipment looked stronger.

I failed to replace washre belt. It is too too tight to be replaced by my man power.

first off I watch the video on how to take this apart and how hard it would be for a women to do it. I then ordered the part from you guys which got here quickly and started the tore down with taking off the front panel on the bottom, unplugging the unit and turning off the water. then I got plenty of towels and started with unpluging the pump, and using a vise grip took off clamps, water drained out and replaced with new pump, when I restarted it still would not drained, found the filter which is located in the big hose itself that comes off the tub filled with hair and junk, you can take a needle nose pliers to pull out the clog or work the white plastic piece out to clean it all the way out then replace back into big hose. put back together and it works.. Thank you..

It is a front load washer with a dryer stacked on top of it.Insaw a video on u tube. I took a neddle nose pliers ang took a spring loaded metal ring off that is holding the grey rubber boot on . I peeled it back just enough to reach ih and get the door lock in hand.I then took a phillip screw driver and removed the two screws un the front off holding the door lock..I then reversed instructions,and put the new lock in.The complete job took lease than 5 minutes,and the part did the trick. My washer works as good as new.

Removed the door lock and switch assembly. With needle nose pliers, I removed the metal ring around the washer gasket. Removed two screws on assembly and removed the entire assembly. Noted part number and ordered part which came in 3 days. Reversed the above instuctions for removing the assembly. Was washing within the hour. By the way, I am a 65 year old woman.