FRSS26L3AF0 Frigidaire Refrigerator - Instructions

Every time I spoke to someone they sent wrong part . Still do not have correct part. Plus had to pay to return part. I sent model number , bin number and they can’t seem to match. Afraid to try again.

Followed the simple instructions on the device and in the appliance use and care manual

The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.

If your fan is still on the shaft, simply push it off ... Read more and extract it the same way. Then place the new one on the shaft.

In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.

Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.

Hope this helps someone. :)

The gaskets aren’t really attached, they are just wedged into a small notch the goes around the entire door. So you can just pull the old one off with no tool. The new one arrived looking very bent and twisted but if you heat it with a hair dryer it goes back to its shape. When installing…You start in the corner and work your way aroun ... Read more d with a butter knife and hair dryer and it eventually sits into the notch. We watched a video on YouTube, it was easy to find a video and easy to do with two people and no tools or experience. Takes a few days for the gasket to feel fully settled into the notch

Removed shelves above the problem area. Tilted new shelf up to slide prongs into openings on one side, pushed in far enough to allow prongs on the other side to fit into their openings. Evened the shelf out then added some thick tape to both sides of the shelf to keep it from falling out.

I BOUGHT 2 MORE SHELVES AND INSTALLED THEM.
THANK YOU

Open freezer
Pry the switch out (bottom first, then push the tab on top while prying out)
Move wires to
New switch
Push switch in
Test

The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.

I removed the broken fan from the condenser. This was very sipmle.

When i pluged the refridgerator back in to the outlet the fan tried to start up but soon be ... Read more gan to make aloud noise, due to there not being enough clerance.

Consulted You Tube. Took off old gasket. Easy. Put on new one after getting it warm. The track on the new gasket did not sit properly. Took multiple attempts but finally worked. Size was perfect but the gasket color was different than original and therefore, different from the refrigerator door. No tools required.

I looked at the internet before I purchased a new seal and saw how to repair it. It was a matter of pulling out the old seal and just popping in the new. The internet said to use a hair dryer to melt the rubber to adhere to the fridge in places where it wasn't. It was quick!

The repair instructions were suspiciously easy sounding- but in actuality- right on! I am not a DIY-er , but I did it! The old gasket came off fairly easily and the new one went right on! No tools needed! There wasn’t an immediate ‘suction/seal’ when I closed the door, but Grok said that was normal, it may take a little time… Sure enough ... Read more - in the morning it was tight! That’s been 2 weeks and so far- so good!

The repair was quick and easy. Just install the ordered bracket ( hinge ) on the top refrigerator door and cover. I had all the screws and cover but somehow the original bracket was missing...hummm

With shelf tilted put one side in and then straighten the shelf to put other side in and then snap in trim. Real easy and less than 5 minutes

I first ordered the wrong switch I called and got a return label and was refunded my money before even shipping the wrong switch I was helped for the right switch and it arrived in 5 days the replacement works perfectly very easy to install. Thank you

The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again.



The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.