FRS6LF7JS3 Frigidaire Refrigerator - Instructions

Removed (unsnapped) plastic cover from back of refrigerator ( inside freezer compartment), determined that the fan was not turning, removed 4 screws from the aluminum back plate in freezer and tilted it down. Removed 2 screws with a nut driver, this allowed the fan to be removed, unpluged fan motor from the bace of the freezer and removed ... Read more fan. Installed new motor and spent $38.00 to repair the refrigerator that would have cost me severial hundred dollars to replace. Thanks for the help

I shut off the water supply and removed the 4 screws from the cardboard back revealing the water valve. I removed the 2 screws which attach the valve to the refrigerator and removed the water valve. Once out it was a snap to unplug the electrical leads and unscrewed the water lines, Insalling the new part was a matter of reversing the a ... Read more bove procedure. Everything is color coded which made this replacement extrememly simple.

I will definitely use you guys in the future. The ordering process was great and delivery time was ultra quick!
Thanks for an easy part replacement and simple install.

most importantly on the page with the necessary part..cripser support for the refrigerator--- there was a brief insructional video on how to properly dislodge the broken part and replace it with the new showing the simple tools needed. I am not handy at all but it took me all of two minutes thanks to the helpful video.

Snap out fan cover, remove four 1/4" screws, remove back cover, remove defective fan motor, remove fan blade, install new motor and blade, strip wires and hook up with wire nuts, reinstall back cover, snap in fan cover, and plug in fridge.

First I unplugged fridge. I then removed cover that keeps fan protected. I then removed 2 screws that hold the evaporator motor in place. I then removed 3 wires running to motor. Very easy to remove, just pulled connections apart. I then replace the old motor with new.

The Sears repairman wanted to charge me $359 to repair. ... Read more I did repair for under $40! Amazing what you can save if you have the time and knowlege to do it yourself.

Just opened the filter storage and popped out the old one and put in the new one. Ran the system for three minutes according to directions and it worked fine.

first i by passed the timing board, with a ele cord to the fan motor to keep the fridge cool till your parts got here, which was realy fast delivered,
the fan would come on because the board was fried.
it took abot 30 min to install every thind just be carefully unpluging anything.things will break i guess metal eing cold makes ... Read more the conne4ctors stick together.
evaporator fan is in the frezzer four screws,tested the wires for ohms,and power, when i pluged in the fan i would loss power to the fan,that told me the board was bad, the same night my furnance when to (reaaly) and i lost my borad on the computer ethernet card (lighting isn't fun) it cost to fix everything about 130.00 thanks for thr great parts

- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.

Once I recieved the new filter, I enthusiastically opened the box, removed the filter from it's packaging and set it aside for quick access. I opened the refrigerator door, pushed the release button on the old filter and pulled it out. I then tossed the old filter in the trash.
Once that was done, I removed the 2 rubber caps covering ... Read more the inlet and outlets on the new filter. Then, with ace precision, I guided the new filter back into the slot until it clicked. I ran the water for 3 minutes as the instructions suggested, then, had a glass of water.
Mission accomplished and it went off without a single hitch!

Glenn Walker, Simi Valley, Ca

Turned off power at C/B panel. Took cover off dispenser, removed 3 screws, board held in by 4 screws. Removed all 4, replaced board after removing connecter. Put back together. Turned power on. Worked perfectly. 15 minutes max, part was $81, recieved 3 days after ordered.

Easy repair, except the re-install of the entire water/ice part back into the door. The original plastic water line too short to fit back into the small opening. Hint: Go buy 10 inch of new water line and a small connector. Run the new line up through the small opening, and connect to the original water line with the small connector ... Read more . This made it easy to replace and test, and then cut of the excess water line.
Thanks.

Removed the cover inside the freezer. Found out that the motor/fan was not working. Ordered through PartSelect. Got the parts in 3 days. Installed it for less than 30 minutes. Very easy. It saved me hundreds of dollars. We considered buying a new fridge but not anymore. , it only cost me $70 including shipment charges. (Make sure you unp ... Read more lug the appliance first before opening the cover. Remember safety first.)

1.Got on line to Partselect ordered the parts we needed .they arrived Quickly and in good condition 2.Except the tray was sent in error delaying the repair. 3.contacted Partselect costumer services for assistance 4.Followed their direction and reorder the correct one hoping the correct one would arrive .it did the next day .5.On to repair ... Read more , removed broken stud with panel stud puller with the aide of a putty knife to spread the pressure of tool stud came out 6.reinserted new stud 7.replaced the new upper crisper drawer cover glass not included . 8.Upper Crisper pan to complete the repair. 9.all in all successful with the help of Partselect superior parts and helpful guides.

First removed the drip tray with a firm tug, Then removed the 2 screws to remove the trim, had to remove the board to get get to the connector. (there is a clip that holds the wire tight) connected the new ribbon cable and secured it with the clip, screwed the board back in and pushed in the other end of the cable. and screwed the trim ... Read more back and the drip tray. surprisingly Very easy to do.

Removed the trim screw on top of the door then removed the two hinge bracket bolts. lifted the door
off placed on the table. Remove the two screws on
holding the bearing bracket on the bottom of the door.
removed the bearing and replace with the new one.
Reinstalled in reverse order.