FH480V (CS21) Kawasaki Engine - Parts

This item has been OEM sourced to ensure a high-quality standard. The gasket is an authentic Kawasaki part that is intended to be used with 4 stroke engines. The gasket is used to seal the connection between the carburetor and the air cleaner assembly. This gasket is sold as a single item.

This metal plate, is an authentic manufacturer replacement part used in outdoor power equipment as a part of the governor assembly. It is one of the two plates attached to the end of the camshaft which plays a key role in regulating the engine speed. When the engine speed increases or decreases, the plates are forced outward or inward, th...Read moreereby actuating the throttle and controlling the amount of air and fuel that enters the engine. This process allows the engine to maintain a consistent speed. If the plates become damaged or dislodged, you will notice fluctuating engine speed and poor load response. Before removing the plates, first disconnect the springs and linkage attached to them. Detach the plates from the camshaft and position the new ones in place.

This governor plate, also known as the governor control, is supplied by the original manufacturer for use in a variety of outdoor power equipment. It is a metal plate that works with the throttle linkage to allow the engine to maintain a consistent speed during operation. If the governor plate wears down or becomes damaged, you will notic...Read moree that the engine will stall under load, and the revolutions per minute (RPM) in your equipment will fluctuate, causing over-speeding or under-speeding as well as inconsistent power output, and performance. Therefore, it is critical to replace this part if it is no longer working, in order to continue operating your equipment. You can find the governor plate near the throttle linkage assembly in your equipment engine. Depending on your model, you may need to remove the air filter housing to access the plate. Disconnect the throttle linkage from the governor plate and remove the faulty governor plate. Place the new one in position, secure it with the appropriate fasteners, and reverse-assemble the rest of the engine components to complete your repair.

It is a genuine OEM sourced replacement part that is specially produced for use with Kawasaki engines commonly installed on lawn and garden equipment. This item fits the opening in the crankcase helps to provide an air tight seal to prevent any leaks. Over time seals tend to get compressed and may begin to deteriorate eventually requiring replacement. It is made of durable rubber material and it is sold individually.

This bolt is generally used to secure muffler on engines. It is supplied from original equipment manufacturer for use with Kawasaki gas powered engines. This bolt has a hex head which requires a wrench for installation. Please note it is sold individually.

This is available as a set that contains all the necessary piston rings. They are genuine Kawasaki and Toro parts sourced directly from the manufacturer for use in engines and lawn tractors. These parts are made out of durable materials. A set of pliers may be necessary during the installation of these items. They may become broken or bent and will need to be replaced.

The valve spring retainer goes between the spring and the collet. This part is made of metal and is available individually. It is an OEM from Kawasaki, Toro, and Lawn Boy for use in engines. A screwdriver, a socket set, and a wrench set might be helpful during the installation of this part. This item will need to be replaced if it breaks.

This flanged bolt is a genuine OEM steel fastener used to secure various components in outdoor power equipment. It features a flange base that acts as a built-in washer to distribute the load and prevent damage to the material it is fastened to. The bolt head has a diameter of 6mm, and the bolt shaft has a thread pitch of 20. The bolt can...Read more corrode and crack over time, or its threads may wear down, leading to loosening or detachment of the connected parts. You will likely note excessive noise, vibrations, and equipment instability. Inspect all the bolts in your equipment and replace those that are no longer functioning. Use a wrench or socket to loosen and remove the old bolt. Position the new bolt on the mounting surface and tighten it securely until the flange is flush against the surface. Each flanged bolt is sold individually.

This replacement air filter element is an authentic OEM sourced item that is specially made for Kawasaki engines. Its purpose is to provide an extra layer of protection from dust and debris in the air that goes in the engine. This for air filter element is sold individually, please note that the main pleated paper filter is sold separatel...Read morey. To replace this filter no special tools would be needed, simply remove the cover and replace the air filter element.