Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lound noise inside dryer
1. unplug the dryer, remove the aluminum vent and move it to an area that has a lot of elbow room. 2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end. 3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the open door sensor. remember which wire goes where. 4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver. 5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place. 6. look in the drum and there is 3 screws that form a triangle shape. remove the screws. 7. remove the belt from the drum. inspect the belt. replace if necessary. 8. lift up and pull out the drum. 9. remove the rear drum assembly and replace it with the new parts. 10. repeat in reverse and your done. It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.
Remove top panel with large flat screwdriver and 2 screws in back.Remove bottom panel with 2 screws.Release belt tensioner and remove belt.Remove 3 screws in center of drum inside.Remove drum. Remove rear bearing by pulling up on assembly.Replace all parts in reverse order.
I just popped up the top front using a large straight (slotted) screw driver, then removed the 2 screws at the bottom front, then the whole front panel popped down about a half inch to be lifted out of the way. I found the old drive belt way down under the motor (still attached as normal), very near the floor and removed the worn out belt by hand, and replaced it with the new belt by hand also. The spring loaded belt tightener- idler wheel makes this a very simple process to accomplish. Then, I replaced the front panel-- all done. Works like new.
This is a washer/ dryer combo unit. Start at the top of the unit. Remove top plate then remove cover between dryer and washer. Remove control panel. Now remove front panel with dryer door. Unplug harness connector. With area now open put on new belt around drum and motor. Be sure you put belt around idler pulley correct way so there is tension on belt. Put back together in reverse order. Took me about 40 minutes since I cleaned and vacuumed out appliance.
The loud noise was present only while using the dryer of my washer/dryer combo unit. I traced the noise down to the rear center of the dryer and I noticed that the noise would stop or be quieter if I pushed on this area with my hand while the dryer was running. I realized there must be some type of bearing supporting the weight of the dryer drum while allowing it to rotate. I did a Google search for parts on my model # and found Parts Select. I used the parts diagrams to figure out what parts were the likely problem. I found the rear bearing part# and watched the very helpful video showing how to replace it.
I removed the drum on my dryer and found the bearing and socket to be completely dry (no grease) and showing a lot of wear. The dryer heat element surrounds the bearing so I think 10 years of use had dried up all the grease. I purchased the bearing kit so I swapped out the old parts for everything in the kit. I also noticed the drum belt was split in places and little black dots all over the inside of the drum area were small pieces of the belt. I replaced the belt and took the opportunity to vacuum the drum area because it was covered with 10 years of lint. The bearing replacement video was extremely helpful and I was able to replace parts easily even though I had a different dryer than in the video. My dryer is much quieter now and I didn't have any screws left over!! I will definitely shop Parts Select again!!
After struggeling the most with lifting out the inner drum and then the wash drum. I realized when the job was complete a better way. 1. Take the top off the washer. 2. take the front off the washer. Then disconnect all wires and hoses from assembly One small hose on the tub and the pump hose at the bottom. 3. at the bottom of the overall assembly there are 3 braces holding the tub assembly with 2 springs on each brace. Go under and remove the springs and then lift the whole assembly out into the middle of the floor. 4. remove the top cap off of the agitator. 5. remove the agitator. 6. if you are lucky and the bolts are not seized in the block that holds the shaft remove the small steel block from the bell and remove the bell. 6. Slide the inner tub up and off the shaft and again if all goes well the outer wash tub should slip up off the shaft as well. 7. remove the drive belt from the motor and transmission.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer squeal
Order the Bearing Kit and Belt. All the necessary parts are included. I used them all and everything fit perfect. For the stack unit have a step stool to reach the screws on top. Remove the top screws. Remove the front panel and door assembly. Be sure to disconnect the electrical connector behind the control panel before you pull out the door assembly. Remove the belt. Pop up the dryer drum and remove. Replace all the bearing parts with new in the kit. Hang the new belt around the drum and reinstall the drum. Connect the belt using the access panel on rear of unit. Reinstall the front panel, door assembly and top panel. A helper to install the new drum bearing bracket is handy.
Dryer would not turn on, no power. Since i already have replaced thermal limiter switch, i knew exactly what to do and also how to shorten installation
Remove 2 screws from back of unit, remove top by lifting and pulling up, set aside. Using pliers,needle-nose, remove the 2 wires from switch, then using a magitized philips screw driver, remove 2 screws holding switch to back of unit, replace switch, reassemble everything. 20 minutes, boom, ur done, dry some clothes now
Pry up top from front remove 2 phillip screws at lower front panel slip belt under tub pulley then around motor pulley push belt tensioner towards back of machine slide belt onto tensioner pulley. (Done)
Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!
The repair requires the front panel to be removed. First remove the top by removing two screws in the back of the top panel. Once the top is removed, you have access to all of fasteners for the front panel. I removed the control panel to give myself more room. Simply remove the wire connectors on the panel and two connectors in the upper right of the cabinet. There are four screws that hold the front panel on, two on the inside about a third from the top and two more on the outside at the very bottom. Once the screws are removed, pry the front panel from the machine since there are spring clips holding the panel to the machine. Once the front panel is removed, you have access to the guides and the felts.
UNPLUG DRYER (this is key) Removed the top of dryer. used screwdriver and pliers to remove two screws and electrical connections then reinstalled new part stick the magnet behind the part to the back of the dryer to help control the small screws.
