Models > FEX831CS0 > Instructions

FEX831CS0 Frigidaire Washer Dryer Combo - Instructions

All Instructions for the FEX831CS0
406 - 415 of 415
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The only probelem was to take out the drum, because it was a washer and dryer combo. the dryer was on top, i did not have any room to pull out the drum
I remove the drum, and install the bearing just like the instructions in the video.
Parts Used:
Rear Drum Bearing Kit
  • Witly from Wheatley Heights, NY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Stopped spinning made noise
Changed the belt started working like new.
Parts Used:
Drive V-Belt
  • Cecilia from Moreno Valley, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
wash timer would not advance
My guy got a beer and followed the advice from John from Covino CA. Thank you John, the part about pulling the pen sure made my guys repair a piece of cake! He replaced the timer and put the panel back on and I was doing a load of laundry immediately. My advice is follow John's advice!
Parts Used:
Timer
  • Elizabeth from Cutchogue, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Need it a new belt and a lint catcher
Open the front panel push the wheel belt and done
Parts Used:
Drive V-Belt Dryer Lint Screen
  • carlos from Berwick, ME
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
My Lint Filter Had A Hole In It
I replace the filter,,,
Parts Used:
Dryer Lint Screen
  • Charles from Centreville, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Cracked
Took cover off and removed damaged part. Removed wiring and reattached to new part
Parts Used:
Terminal Block Kit
  • Gary from Girard, KS
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
ball hitch wore out
Not bad two people needed for alignment
Parts Used:
Multi-Rib Drum Belt Drum Support Bearing Rear Drum Bearing Kit Dryer Drum Bearing Bracket
  • Mark from Marion, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Heater coil broken
Once the drum was removed it only took 10 min to remove and replace the coil. It took approx one hour to complete
Parts Used:
Heater Assembly
  • Joan from Conway, SC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door would not close because of broken female latch.
Very simple. I removed the broken latch with pliers and snapped in the new one in less than 5 minutes.
Parts Used:
Door Catch
  • Raymond Frattone from Richboro, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
loud squeek
followed the Video instruction which were provided. Dryer works like brand new.
Parts Used:
Rear Drum Bearing Kit
  • Cheryl from Weirton, WV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the FEX831CS0
406 - 415 of 415
Back to Top