- Home
- FEF388CCBC
- Instructions
FEF388CCBC Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Element did not heat
2 of 3 people
found this instruction helpful.
-
Susan from Iowa City, IA
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench set
After doing without the oven for a week or so we decided to turn to the internet and try doing the repair ourselves. We are not mechanically inclined/fix it yourself kind of people. This really was easy. Just detach the old element and attached the new one. A couple of bolts and snapping one out and then the new one in. Very simple
Was this helpful?
Thank you for voting!
heating element stopped working
2 of 3 people
found this instruction helpful.
-
Kevi from Verona, WI
- Really Easy
- Less than 15 mins
-
Wrench set
All I had to do was loosen the screws, pull out electrical hookup on both ends, hookup new heating element to elecric and screw em into place. That's it, super easy and I got the part in 2 day : )
Was this helpful?
Thank you for voting!
Lacking oven racks on used appliance
2 of 3 people
found this instruction helpful.
-
Katherine from Roanoke, VA
- Really Easy
- Less than 15 mins
Your website is great...easy and it literally took me no mote than 5 minutes to find what I needed and order...and received it VERY quickly. Must say I was dreading going to some parts house that we have in our town in bad area, and searching on dusty shelves for what I needed...am so glad I found you!!
Was this helpful?
Thank you for voting!
oven Bake Element burned up and broke
2 of 3 people
found this instruction helpful.
-
Robert from Hopkinsville, KY
- Really Easy
- Less than 15 mins
-
Nutdriver
this bake element has two special Hex style screws, securing it in place, but a nut driver worked just as well. remove the baking racks, and then loosen the two hex screws. slowly pull the element out of the back wall and then disconnect the electric leads. reinstall by doing then the opposite action. could not have be simpler.
Was this helpful?
Thank you for voting!
Bake element wouldn't heat.
2 of 3 people
found this instruction helpful.
-
Earl from Elkin, NC
- Easy
- Less than 15 mins
-
Nutdriver
The problem was caused by the owner placing an aluminum catch pan under the bake element. The failure of the element was where it was in contact with the pan. The repair involved removing two screws pulling out the element to access the wires. The connectors were the pull off type so I just disconnected the wires from the old element and
... Read more
placed them on the new element, pushed the element back in place and replaced the two retaining screws. I suggested that the owner not place anything in contact with the bake element. Be sure to up-plug the stove plug before attempting repair.
Read less
Was this helpful?
Thank you for voting!
The right Drawer Glide was broken.
2 of 3 people
found this instruction helpful.
-
Fred from Gregory, MI
- Really Easy
- Less than 15 mins
The simplest repair ever! I just snapped it in and put the drawer back - fixed. I hope I have other repairs this simple.
Was this helpful?
Thank you for voting!
oven drawer would not open or shut completely
1 person
found this instruction helpful.
-
Howard from Poteau, OK
- Really Easy
- Less than 15 mins
-
Screw drivers
first I emptied the contents of the drawer,then pulled drawer open to it's fullest, then lifted drawer so as to tilt slightly, then removed drawer by continuing to pull straight out. then I removed the glide from its protective packaging and inserted it in the same spot as the broken glide was at one time
Was this helpful?
Thank you for voting!
Bake element broken
1 person
found this instruction helpful.
-
Richard from Campbell, CA
- A Bit Difficult
- Less than 15 mins
-
Nutdriver, Pliers
Removed screws. Tried to pull out old element but spade lugs on old element were bent at ninety degree angle. Once I figured that out I was able to manouver the old element out with the attached wires. Had to be carfull that the loose wires did not slip back ijn through the hole. Reaching in over the oven door was a but diffcult, but all-
... Read more
in-all the jobe was done in a few minutes.
Read less
Was this helpful?
Thank you for voting!
bake element burned up
1 person
found this instruction helpful.
-
charles from cartersville, GA
- Really Easy
- Less than 15 mins
-
Nutdriver
removed two screws pulled element out about four to five inches attached wire to new element screwed back in less than ten minutes done
Was this helpful?
Thank you for voting!
originaldrawer guide was cruched out of useable shape
1 person
found this instruction helpful.
-
Fred from Ocala, FL
- Really Easy
- Less than 15 mins
-
Pliers
first thing was to remove the crushed guide with pliers and a twist it was out. to install the new one islipped one side into the slot and took pliers and applied pressure on the lower glide into the slot; it was done presto. works like new. thanks,
Fred . it was so reasonable i got a spare.
Fred . it was so reasonable i got a spare.
Was this helpful?
Thank you for voting!
oven wouldn't heat
1 person
found this instruction helpful.
-
Michael from Goddard, KS
- Really Easy
- Less than 15 mins
-
Nutdriver
using a nut driver I removed to two screws that were holding the element in place. Then simply disconnected each wire. Removed the old element and plug the new wires onto the new element. Reinstalled the two screws and everything works fine
Was this helpful?
Thank you for voting!
Baking element burned out
1 person
found this instruction helpful.
-
Richard from Aiken, SC
- Really Easy
- Less than 15 mins
-
Nutdriver
The element went out on a Wednesday. We ordered the part the next day. We received it the following Tuesday (Mon. was a holiday). My 16 yr. old son replaced the part within 15 minutes. It was a piece of cake-actually it was a pizza!!
First and foremost we turned off the breaker, a very important thing to remember!! Then he removed t ... Read more he two screws that hold the element in place. He then pulled the element out about 3 inches and disconnected the two wires...and reconnected the new ones and put screws back in. Voila!! Ours was stillll under warranty, but we would have had to pay the service call and labor costs. Our do it yourself was much cheaper and faster!!
First and foremost we turned off the breaker, a very important thing to remember!! Then he removed t ... Read more he two screws that hold the element in place. He then pulled the element out about 3 inches and disconnected the two wires...and reconnected the new ones and put screws back in. Voila!! Ours was stillll under warranty, but we would have had to pay the service call and labor costs. Our do it yourself was much cheaper and faster!!
Read less
Was this helpful?
Thank you for voting!
Original Elememt went bad
1 person
found this instruction helpful.
-
Steve from Orefield, PA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
The directions have been stated many time and they are quite simple. Take out the two screws, pull the element so the wire connections come through into the oven. Disconnect the element at the wire connectors and replace. This is a dirt easy job.
The only real area for a potential problem is pulling the wire connectors thr ... Read more ough into the oven. As long as you pull slow and from the back - right next to the whole, you will be fine. Take the connectors off carefully and you're golden. Easy job.
The only real area for a potential problem is pulling the wire connectors thr ... Read more ough into the oven. As long as you pull slow and from the back - right next to the whole, you will be fine. Take the connectors off carefully and you're golden. Easy job.
Read less
Was this helpful?
Thank you for voting!
bake element burnt into
1 person
found this instruction helpful.
-
don from whiteville, NC
- Easy
- Less than 15 mins
-
Nutdriver
i removed the back panel removed two screws pulled the element out
Was this helpful?
Thank you for voting!
Oven would not heat up-
1 person
found this instruction helpful.
-
Charles from Hagerstown, MD
- Easy
- Less than 15 mins
-
Nutdriver, Pliers
Disconnected the main electrical plug from the wall for the oven..
Used a nut driver to remove the two screws that held the heating elementin place.
Pulled the element out so I could remove the two wire terminals.
Installation of the new heating element was fairly basic..Oven is working great..
Used a nut driver to remove the two screws that held the heating elementin place.
Pulled the element out so I could remove the two wire terminals.
Installation of the new heating element was fairly basic..Oven is working great..
Was this helpful?
Thank you for voting!