- Home
- FEF388CCBC
- Instructions
FEF388CCBC Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Old heating element broke
2 of 2 people
found this instruction helpful.
-
Paul from Ellenville, NY
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Drank a beer, grabbed a screwdriver & tried to remove the two screws that held the element in place. The screws were old and when I turned them, they stripped instantly. This required another beer. Eventually I used pliers to grip the sides of the screws to remove and reinsrt them. When I finished the oven worked great, so I celebrated wi
... Read more
th another beer.
Read less
Was this helpful?
Thank you for voting!
oven door not closing completely
2 of 2 people
found this instruction helpful.
-
David from BIRDSBORO, PA
- Very Easy
- 15 - 30 mins
older range required no tools to repair, pulled old gasket out of notches at bottom of door, popped clips out of pre-drilled holes, folded new gasket ends {2 inches} and pushed into door, pushed clips into place.
Was this helpful?
Thank you for voting!
Oven bake element failed.
2 of 2 people
found this instruction helpful.
-
Gerald from PALM COAST, FL
- Easy
- 15 - 30 mins
-
Nutdriver
I watched the video of the repair. It was very easy; removed 2 screws; disconnected 2 push-on tabs; removed the element; and then reversed the operation. Be sure to turn off the circuit breaker that powers the oven before you start the repair. Turn it back on when finished and test the oven.
Was this helpful?
Thank you for voting!
bake element burnt out.
2 of 2 people
found this instruction helpful.
-
james from WOOTON, KY
- Really Easy
- 15 - 30 mins
-
Screw drivers
removed screws,unplugged terminal leads,installed new one,back in business.
Was this helpful?
Thank you for voting!
Bottom oven element non-functional
2 of 2 people
found this instruction helpful.
-
Louis from GAINESVILLE, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Shut off power - throw breaker. Oven access easier with door removed - requires removal of two Phillips head screws. Remove two screws holding element in place using 1/4" socket. Pull element & wires out and pull slide in connectors out (had to hold the wire end with needle nose pliers}. Installed element by reversing the removal proc
... Read more
edures. Also good time to clean oven.
Read less
Was this helpful?
Thank you for voting!
Element burnt out and cracked
2 of 2 people
found this instruction helpful.
-
Robert from LOUISVILLE, KY
- Very Easy
- 15 - 30 mins
-
Nutdriver
I simply followed the instructions in your video. i shut down the power to the oven via the breaker panel, removed the two quarter inch screws with a nut driver, pulled out the old element exposing the two wire leads,disconnected one lead at a time and duct taped each lead to the oven wall,. Then removed the old element and replaced th
... Read more
e new one in reverse order. Voila! It works great. This is the second element I replaced in this oven over the years. This site was prompt on shipping the new element (about 3 days since I ordered on a Sunday).. It was well packed and arrived on time and I even got an e-mail letting me know it arrived! How cool is that?! I've been a customer for a few years now and plan to be a "forever" customer. Thanks for saving the day! You ROCK!
Read less
Was this helpful?
Thank you for voting!
Old part was replaced by mfg’r. Wiring different. No drawings or any info was included to show wiring.
2 of 2 people
found this instruction helpful.
-
Nelson from FRUITHURST, AL
- Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
I was forced to call in a pro repairman. Will cost me at least $150 for part and repairman. I could have done job if instructions on how to rewire had been included.
Was this helpful?
Thank you for voting!
Bake Element burned in to stopped working
2 of 3 people
found this instruction helpful.
-
Debbie from Mineral Wells, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver
Turned off power to appliance removed the screws connecting the element. Disconnected the wires from the old element connected the new element replaced the screws and tightened turned power on turned power back on heated oven to be sure it worked. Very simple to do.
Was this helpful?
Thank you for voting!
bake element burnt out
2 of 3 people
found this instruction helpful.
-
Kim from Union Grove, WI
- Really Easy
- 15 - 30 mins
-
Nutdriver
I looked for the proper part on this site. I was even able to find a video on how to install the part. It was great to see the step-by-step directions and tools needed. I ordered the part. It came quickly so that I was able to get my oven repaired before my kids came home for spring break. The only problem I had was the old screws were re
... Read more
ally stuck on. I used some WD-40 and they were still quite stuck. I learned that by gently going back and forth with the nut driver, rather than just trying to turn in the correct direction, that the screws came out quite easily. I felt so proud to be able to fix my own stove and save money in the process! Very satisfying for a single mom. Couldn't have done it without the video directions.
Read less
Was this helpful?
Thank you for voting!
Broken drawer slide
2 of 3 people
found this instruction helpful.
-
Michael from Jacksboro, TN
- Really Easy
- Less than 15 mins
Remove drawer. Insert new slide. Install drawer.
Was this helpful?
Thank you for voting!
Broken right side parts for lower over storage drawer.
2 of 3 people
found this instruction helpful.
-
Ty from Baltimore, MD
- Easy
- Less than 15 mins
-
Screw drivers
Sat on floor, pulled drawer out, inserted new clips, remounted door, stood up, high-fives myself.
Other Parts Used:
Was this helpful?
Thank you for voting!
lens was broken
2 of 3 people
found this instruction helpful.
-
Kenneth from Coeur d'Alene, ID
- Really Easy
- Less than 15 mins
after pulling away from wall and unplugging remove 5 screws in upper back panel lift off being careful of sharp edges if part of lens is still in hole push it out towards the front insert lens from front of unit slide light assy over pin on back of lens replace back panel plug in range push back against wall check for level you're done
Was this helpful?
Thank you for voting!
Bottom bake element went bad
2 of 3 people
found this instruction helpful.
-
James from Martinsburg, WV
- Really Easy
- Less than 15 mins
-
Nutdriver
Remove the 2 nuts holding the element in place. Pull the element out slightly to expose the wires. each side of the element has a wire. Slide the wires off. Replace new element. attach wires and pu the 2 screws back in the element holders.
Was this helpful?
Thank you for voting!
Oven bake element was dead
2 of 3 people
found this instruction helpful.
-
Stephen from Spencer, IN
- Really Easy
- Less than 15 mins
-
Pliers, Socket set
Turned off range/oven breaker. Opened the oven door. Removed two 5/16 hex head screws. Pulled bake element forward and removed the two slip on electrical connections from old bake element and put them on the new one. Replaced the two screws, closed the oven door, and proceeded to overhaul the kitchen faucet.
Was this helpful?
Thank you for voting!
Oven lower element broke
2 of 3 people
found this instruction helpful.
-
Peggy from Owensville, MO
- Really Easy
- Less than 15 mins
-
Screw drivers
Take the screws out of the inside of oven for the element and slide the oven away from way and remove the back and insert the element to the clips and screw the back of the oven back together and plug in again and push back in place. Very easy for my husband to repair.
Was this helpful?
Thank you for voting!