- Home
- FEF387CCTC
- Instructions
FEF387CCTC Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burner switch work sometime.
3 of 4 people
found this instruction helpful.
-
junius from WICOMICO, VA
- Really Easy
- 1- 2 hours
-
Nutdriver
I follow the video on your site
Was this helpful?
Thank you for voting!
Bake element bad, broiler element OK.
5 of 10 people
found this instruction helpful.
-
Gerry W. from Oxford, IA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Unplugged the stove first !
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from ... Read more a local dealer!
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from ... Read more a local dealer!
Read less
Was this helpful?
Thank you for voting!
Lens cover for the oven light
3 of 4 people
found this instruction helpful.
-
Larry from COZAD, NE
- Really Easy
- 30 - 60 mins
Very easy just had to pull the wire up that holds it secure.
Was this helpful?
Thank you for voting!
The baking element developed hot spots and stoped working.
2 of 2 people
found this instruction helpful.
-
Jeremiah from Crawfordsville, IA
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
I removed the baking racks then unscrewed the default screws for the baking element.I then disconnected the electrical leads from the damaged element. I then removed the old damaged baking element and installed the new baking element, attaching the electrical leads after cheking for weak spots in the element. I then re installed the bakin
... Read more
g racks and started the oven to burn off any factory oils on the baking element.
Read less
Was this helpful?
Thank you for voting!
Toggle switch wouldn't toggle.
2 of 2 people
found this instruction helpful.
-
Kenneth from St.Joseph, MO
- Really Easy
- Less than 15 mins
-
Screw drivers
Unpluged unit then using a flat screwdriver pride out old switch,pull off wires replace on new switch & push new switch in place. Repluged unit reset clock. Done!
Was this helpful?
Thank you for voting!
Door handle was cracked due to a loose screw.
2 of 2 people
found this instruction helpful.
-
Marilynn from Bridgewater, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
Lifted the drawer out from the oven and removed top and bottom screws. Replaced the handle and tightened the screws.
Was this helpful?
Thank you for voting!
bake element burned out
2 of 2 people
found this instruction helpful.
-
Kenneth from Wantage, NJ
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unscrewed screws in back of oven holding element. Slipped old element off of wire. No need to cut wires has the kind of ends (spade ends I think they are called) that just is pushed on to element. Attached new element. slid wires back into wall of wire rescrewed to oven wall. Very easy just be sure wires don't get pulled back into b
... Read more
ack wall of oven. Don't know what you would do then.
Read less
Was this helpful?
Thank you for voting!
Bake element (bottom of oven) burnt through and snapped in two
2 of 2 people
found this instruction helpful.
-
Amber from CARLISLE, PA
- Very Easy
- Less than 15 mins
-
Screw drivers
Unplug the oven, remove oven racks, unscrew 2 screws at the base of oven bake element, pull the terminals off the wire bases, plug terminals back in, put screws back in place, plug in oven and test that it works...
Was this helpful?
Thank you for voting!
Bad element
2 of 2 people
found this instruction helpful.
-
david from PERRY, ME
- Very Easy
- Less than 15 mins
-
Screw drivers
Remove screws pull off wires and install new parts
Was this helpful?
Thank you for voting!
Heating element went out
3 of 5 people
found this instruction helpful.
-
ROBERT from MAINEVILLE, OH
- Very Easy
- Less than 15 mins
-
Nutdriver
Simply...2 hex head screws removed. Unplug old element...plug in new element...place 2 screws back into place...test
Was this helpful?
Thank you for voting!
Oven element burnt out.
3 of 5 people
found this instruction helpful.
-
Dave from LOUDONVILLE, OH
- Very Easy
- Less than 15 mins
-
Nutdriver
Remove 2 screws. Pull element out. Slide 2 wires off. Just do in reverse it's done.
Was this helpful?
Thank you for voting!
Burner not controlable
2 of 2 people
found this instruction helpful.
-
Royce from KEENE, TX
- Very Easy
- Less than 15 mins
-
Screw drivers
Removed rear panal, removed screws from of switch. Unplued wires and installed new switch and put back together. Very easy.
Was this helpful?
Thank you for voting!
Bake element burned out
2 of 2 people
found this instruction helpful.
-
Mark from LAUREL, MD
- Very Easy
- Less than 15 mins
-
Nutdriver
This is an easy repair, as described in several other replies. One important addition to what has already been described. Very important to turn off the breaker or unplug the range. One terminal of the range is connected to a hot wire and the range housing is grounded. You may not manage to electrocute yourself, but you could cause and ar
... Read more
c that damages the housing or connector. Turn off the power. Beyond that, simple. Unscrew two 1/4" screws with a nut driver, slide the element out and disconnect the wire connectors. Reverse procedure to install the new element and turn the power back on. Preheat briefly to burn off any odor. Very easy repair.
Read less
Was this helpful?
Thank you for voting!
broke
2 of 2 people
found this instruction helpful.
-
Richard from COFFEYVILLE, KS
- Very Easy
- Less than 15 mins
-
Socket set
took out the old one, screwed in the new one. very easy.
Was this helpful?
Thank you for voting!
problem pulling out bottom tray on range
2 of 2 people
found this instruction helpful.
-
rosetta from COLUMBIA, VA
- Really Easy
- Less than 15 mins
just put in slot
Was this helpful?
Thank you for voting!