- Home
- FEF352CATC
- Instructions
FEF352CATC Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken handle on the lower door
2 of 2 people
found this instruction helpful.
-
Robert from Albuquerque, NM
- Really Easy
- 15 - 30 mins
-
Screw drivers
I removed the screws holding the element in place. Then I screwed in the new part. No problem at all.
Was this helpful?
Thank you for voting!
bake element burnt out.
2 of 2 people
found this instruction helpful.
-
james from WOOTON, KY
- Really Easy
- 15 - 30 mins
-
Screw drivers
removed screws,unplugged terminal leads,installed new one,back in business.
Was this helpful?
Thank you for voting!
Bottom oven element non-functional
2 of 2 people
found this instruction helpful.
-
Louis from GAINESVILLE, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Shut off power - throw breaker. Oven access easier with door removed - requires removal of two Phillips head screws. Remove two screws holding element in place using 1/4" socket. Pull element & wires out and pull slide in connectors out (had to hold the wire end with needle nose pliers}. Installed element by reversing the removal proc
... Read more
edures. Also good time to clean oven.
Read less
Was this helpful?
Thank you for voting!
Original terminal degraded and faulty
2 of 2 people
found this instruction helpful.
-
Robert from PRAIRIEVILLE, LA
- Easy
- 15 - 30 mins
-
Screw drivers
Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto
... Read more
each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.
Read less
Was this helpful?
Thank you for voting!
bake element burned out
2 of 2 people
found this instruction helpful.
-
Kenneth from Wantage, NJ
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unscrewed screws in back of oven holding element. Slipped old element off of wire. No need to cut wires has the kind of ends (spade ends I think they are called) that just is pushed on to element. Attached new element. slid wires back into wall of wire rescrewed to oven wall. Very easy just be sure wires don't get pulled back into b
... Read more
ack wall of oven. Don't know what you would do then.
Read less
Was this helpful?
Thank you for voting!
Original Element physically broke
2 of 2 people
found this instruction helpful.
-
Beverly from WEATOGUE, CT
- Very Easy
- Less than 15 mins
There is an installation video , but it was so easy, and if you clean your drip pans from those inevitable spills you can do this. I have zero mechanical abilities and I did. The website makes it easy to find your part, and the original literature you got with your appliance will direct you where to find the
... Read more
Model # and serial # on your Frigidaire Range. Order your part on line, get it in the mail and insert the Element yourself.Very happy with my transaction.
Read less
Was this helpful?
Thank you for voting!
Heating element went out
3 of 5 people
found this instruction helpful.
-
ROBERT from MAINEVILLE, OH
- Very Easy
- Less than 15 mins
-
Nutdriver
Simply...2 hex head screws removed. Unplug old element...plug in new element...place 2 screws back into place...test
Was this helpful?
Thank you for voting!
Oven element burnt out.
3 of 5 people
found this instruction helpful.
-
Dave from LOUDONVILLE, OH
- Very Easy
- Less than 15 mins
-
Nutdriver
Remove 2 screws. Pull element out. Slide 2 wires off. Just do in reverse it's done.
Was this helpful?
Thank you for voting!
Burner not controlable
2 of 2 people
found this instruction helpful.
-
Royce from KEENE, TX
- Very Easy
- Less than 15 mins
-
Screw drivers
Removed rear panal, removed screws from of switch. Unplued wires and installed new switch and put back together. Very easy.
Was this helpful?
Thank you for voting!
Burner rings did not fit.
2 of 2 people
found this instruction helpful.
-
JOANNE from IMPERIAL, PA
- Very Easy
- Less than 15 mins
The replacement rings were so easy to install, and the little clip to hold them in place is really smart. Made my old range look really nice again. I thought the cost for the four rings was a bit high but they were well worth it. Thank You
Other Parts Used:
Was this helpful?
Thank you for voting!
problem pulling out bottom tray on range
2 of 2 people
found this instruction helpful.
-
rosetta from COLUMBIA, VA
- Really Easy
- Less than 15 mins
just put in slot
Was this helpful?
Thank you for voting!
broke
2 of 2 people
found this instruction helpful.
-
Richard from COFFEYVILLE, KS
- Very Easy
- Less than 15 mins
-
Socket set
took out the old one, screwed in the new one. very easy.
Was this helpful?
Thank you for voting!
Bake element burned out
2 of 2 people
found this instruction helpful.
-
Mark from LAUREL, MD
- Very Easy
- Less than 15 mins
-
Nutdriver
This is an easy repair, as described in several other replies. One important addition to what has already been described. Very important to turn off the breaker or unplug the range. One terminal of the range is connected to a hot wire and the range housing is grounded. You may not manage to electrocute yourself, but you could cause and ar
... Read more
c that damages the housing or connector. Turn off the power. Beyond that, simple. Unscrew two 1/4" screws with a nut driver, slide the element out and disconnect the wire connectors. Reverse procedure to install the new element and turn the power back on. Preheat briefly to burn off any odor. Very easy repair.
Read less
Was this helpful?
Thank you for voting!
Oven element broke
2 of 2 people
found this instruction helpful.
-
Irving from Germantown, MD
- Easy
- Less than 15 mins
-
Nutdriver
It took me more time to find the right tool then to remove and replace the element. If I can do it anybody can do it. Removed two (2) screws with a nutdriver. Detached the element replaced with new element and replaced screws. Easy job!
Was this helpful?
Thank you for voting!
The oven went out, element wouldn't turn off.
2 of 2 people
found this instruction helpful.
-
Howard from McPherson, KS
- Really Easy
- Less than 15 mins
-
Nutdriver
It's a simple project. Remove old element and replace it with new one. Access is easy. Only one tool needed. What impressed me was how fast the part got here, like the next day after I ordered it.
Was this helpful?
Thank you for voting!