- Home
- EV200NXEW01
- Instructions
EV200NXEW01 Whirlpool Freezer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
19 year old light switch broke
0 of 1 people
found this instruction helpful.
-
Fred from Watertown, NY
- Really Easy
- Less than 15 mins
Great service. Unpluged old switch and pluged in new one. Works great
Was this helpful?
Thank you for voting!
rocker switch broke off
0 of 1 people
found this instruction helpful.
-
STANLEY from OAKLAND, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.
Was this helpful?
Thank you for voting!
light staying on
0 of 1 people
found this instruction helpful.
-
Cecelia from Beaver Dam, WI
- Easy
- 15 - 30 mins
-
Screw drivers
A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.
Was this helpful?
Thank you for voting!
light switch would not work
0 of 2 people
found this instruction helpful.
-
Joseph from Destin, FL
- Really Easy
- Less than 15 mins
Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!
Was this helpful?
Thank you for voting!
non-functioning refrigerator lite switch
0 of 2 people
found this instruction helpful.
-
Ronald from Billings, MT
- Really Easy
- Less than 15 mins
-
Pliers, Wrench set
My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sin ... Read more cerely, Ron Marshall, Billings, MT
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sin ... Read more cerely, Ron Marshall, Billings, MT
Read less
Was this helpful?
Thank you for voting!
The light went out
0 of 2 people
found this instruction helpful.
-
Janet from Flagstaff, AZ
- Easy
- Less than 15 mins
-
Screw drivers
I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.
Was this helpful?
Thank you for voting!
Switch was not working after a repairman had fixed something else
0 of 4 people
found this instruction helpful.
-
Jackie from Nova, OH
- Really Easy
- Less than 15 mins
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a
... Read more
single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.
Read less
Was this helpful?
Thank you for voting!
Both outside door handles turned very beige
23 of 76 people
found this instruction helpful.
-
Howard from Boynton Beach, FL
- Easy
- 30 - 60 mins
-
Nutdriver
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol
... Read more
oring refer handles. Thank you
Read less
Was this helpful?
Thank you for voting!
Both light bulbs had been replaced, but lights did not turn on.
-
Richard from Arlington, MA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.
Was this helpful?
Thank you for voting!
Switch didn't work
-
Don from Laramie, WY
- Easy
- 15 - 30 mins
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00
Was this helpful?
Thank you for voting!
Not freezing or keeping cold and no fans or motors running
-
Glenda from Chester, MT
- Easy
- 15 - 30 mins
-
Pliers, Socket set, Wrench (Adjustable)
I had the best luck using pliers to remove the hex top screws. Once the screws were removed I unplugged the old defrost timer and plugged in the new one. Replaced the screws and the freezer worked when plugged in.
Was this helpful?
Thank you for voting!
Broke the arm off the food compartment rocker switch
-
David from St. Pete Beach, FL
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips
... Read more
were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.
Read less
Was this helpful?
Thank you for voting!
No light in frig
-
Irene from Whitehall, MT
- Really Easy
- Less than 15 mins
We tried repairing with a new switch which was very easy to install but it didn't fix the problem.
Was this helpful?
Thank you for voting!
Light switch which turns on the lights when the door opens went out
-
Dennis from Lawrenceville, GA
- Really Easy
- Less than 15 mins
-
Nutdriver
This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.
Was this helpful?
Thank you for voting!
exchange of defective light rocker switch
-
Steve from River Edge, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch
Was this helpful?
Thank you for voting!