ETW4400WQ1 Estate Washer - Overview
Sections of the ETW4400WQ1
[Viewing 9 of 9]Manuals & Care Guides for ETW4400WQ1
Click to downloadInstall
Installation Instructions
(3.72MB)
Manual
Owner's Manuals
(1.95MB)
Manual
Owner's Manuals
(3.31MB)
Manual
Owner's Manuals
(2.25MB)
Keep searches simple, eg. "belt" or "pump".
Agitator Directional Cogs
PartSelect #: PS388034
Manufacturer #: 80040
This kit is used for replacing the agitator directional cogs (Agitator Dogs, Agitator Repair Kit, Washer Agitator Dogs, Agitator Dog Ears). The agitator is what creates the thrusting motion in your wa...
$4.39
In Stock
Direct Drive Motor Coupling
PartSelect #: PS1485646
Manufacturer #: 285753A
This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission and the motor shaft....
$18.89
In Stock
Agitator Repair Kit
PartSelect #: PS334650
Manufacturer #: 285811
This kit (Medium Cam Agitator Repair Kit, Washer Agitator Cam Repair Kit, Cam Agitator) is used to repair the agitator. These parts are located inside the agitator auger near the top. You will need t...
$14.01
In Stock
Suspension Spring
PartSelect #: PS11743345
Manufacturer #: WP63907
The suspension spring supports the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down or has stretched out and lost its spring, it could c...
$8.00
In Stock
Clutch Assembly
PartSelect #: PS334641
Manufacturer #: 285785
A clutch assembly (Clutch, Washer Clutch) is found in your washing machine and is responsible for spinning the basket during the spin cycle. The clutch lining can wear over time. If the clutch lining ...
$27.55
In Stock
Agitator Bolt
PartSelect #: PS11741866
Manufacturer #: WP358237
This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".
$7.03
In Stock
Washer Lid Switch
PartSelect #: PS11745957
Manufacturer #: WP8318084
This part is found in your washer. The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed. This part includes the green grounding wire. If your machine is ...
$45.93
In Stock
Thrust Spacer
PartSelect #: PS334562
Manufacturer #: 285587
This is a genuine OEM thrust spacer for your washer, and is also commonly known as a retainer ring. The spacer is about 2.5 inches in diameter, is made of plastic, and is white in color. It is used in...
$7.62
In Stock
Seal, Inner Cap
PartSelect #: PS11748108
Manufacturer #: WPW10072840
This is an inner cap seal, but may also be known as an O-ring, and it is a part for your washing machine. Some symptoms replacing this part will fix include: leaking from your appliance, uncontrollabl...
$11.09
In Stock
Agitator Cap Barrier with Seal
PartSelect #: PS11748113
Manufacturer #: WPW10074580
The O-Ring is included with this cap. It can be purchased separately as Part #WPW10072840.
$11.09
In Stock
Washer Water Inlet Valve with Thermistor
PartSelect #: PS11749042
Manufacturer #: WPW10144820
This part is used to help control and balance the water temperature flowing in to the washer tub.
$59.82
In Stock
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.41
In Stock
Questions And Answers for ETW4400WQ1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- 2
- 3
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Rebecca
December 29, 2019
Will start to fill than stops. So I push the knob to stop it. Then I'll pull it back out it will start for a few seconds and then it will stop the filling again. I can keep doing this until it fills up but that takes almost 45 minutes to an hour.
For model number ETW4400WQ1
Hello Rebecca, Thank you for the question. I suggest testing the Washer Lid Switch, PartSelect Number PS11745957. Make sure the wires are not lose or damaged. The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed. This part includes the green grounding wire. If your machine is having trouble starting, filling, is not agitating, spinning, or is not draining properly, this could be because the lid switch has broken. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Shannon
October 11, 2021
My size knob small/large/super knob will not turn. It’s stuck on small. What is wrong? How do I fix? Thank you
For model number ETW4400WQ1
Hello Shannon, Thank you for the question. This could indicate the Switch, PartSelect Number PS11750715 for the knob is defective and will need to be replaced. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Jeremy
June 10, 2022
It will fill up but it's like it binds up and will not agitate or spin out
For model number ETW4400WQ1
Hello Jeremy, thank you for your question. There are some main parts that will need to be checked. The Agitator Repair Kit PS334650 and Clutch Assembly PS334641 as well as Direct Drive Motor Coupling PS1485646. There are videos for all on our site for you to view. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
William
December 20, 2023
Water gradually drips into washer after final spin cycle
For model number ETW4400WQ1
Hello William, thank you for the question. We would recommend checking the water inlet valve, part number PS11749042, to fix the issue. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Patrick
January 21, 2024
Is the spin belt on estate by whirlpool washing machines located on the bottom and if so do you have any videos showing how to replace it?
For model number ETW4400WQ1
Hello Patrick, Thank you for your inquiry. We show that the model number you have provided is a direct drive system that does not use a belt. It uses a gearcase and direct drive motor coupling. We do have videos under the related part numbers to show you how to install them. We hope this helps.
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- 2
- 3
- Next >
Common Symptoms of the ETW4400WQ1
[Viewing 16 of 16]Will not agitate
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Shaking and Moving
Fixed by
these parts
these parts
Show All
Does not dispense fabric softener or detergent
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Water Filling Issues
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No movement from Basket & agitator
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pum ... Read more p.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pum ... Read more p.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly.
Read less
Parts Used:
-
Jeff from Wayne, NJ
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
1099 of 1185 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer wouldn't agitate
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the a ... Read more gitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out).
Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.
Slip the new cogs into the underside of the cup, and slide the cup back down in the a ... Read more gitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out).
Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.
Read less
Parts Used:
-
mike from Kent, WA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
936 of 1022 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper portion of agitator, no longer pushing clothing down.
The instructions came with the repair kit, it was fairly simple and straight foward.
One bolt held the entire agitator unit in the washer, as well as held the upper and lower halves together. Once that nut was removed the two halves seperated and the plastic clutch pieces could easily be replaced wtih the new onces in the repai ... Read more r kit.
Very easy do-it-yourself repair! Took about 20 minutes because I was being cautious. Next time I could do it in 5 minutes.
One bolt held the entire agitator unit in the washer, as well as held the upper and lower halves together. Once that nut was removed the two halves seperated and the plastic clutch pieces could easily be replaced wtih the new onces in the repai ... Read more r kit.
Very easy do-it-yourself repair! Took about 20 minutes because I was being cautious. Next time I could do it in 5 minutes.
Read less
Parts Used:
-
Matt from Pawtucket, RI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Socket set
798 of 831 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!