ER1410 Frigidaire Freezer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Our freezer warmed up and we had to throw out all the food.
0 of 1 people
found this instruction helpful.
-
Judith from Black Diamond, WA
- Easy
- 15 - 30 mins
-
Screw drivers
We were looking for a new freezer --thinking it wouldn't be worth calling a repairman. I was trying to determine the size of the freezer and couldn't find it in the manual. So I googled the model number and stumbled upon this site. Thought it would be worth a try and $12 plus shipping to replace the thermostat. Got the thermostat a co
... Read more
uple days later, followed the video directions to replace it--not hard! Plugged it in and it is working great!!! SOOOOO glad I stumbled on your site! You saved us $700-$800!! Thank you! Thank you! Thank you!
Read less
Was this helpful?
Thank you for voting!
Evaporator freezing up. Noticed Ice cream not frozen solid
0 of 1 people
found this instruction helpful.
-
Paul from Buffalo, MN
- Really Easy
- 30 - 60 mins
-
Screw drivers
Notice ice build up on the panel in front of the evaporator coil. Unplugged freezer and removed evaporator panel. Plugged unit back in and checked fan, coil "snap switch" and heater element, all seemed to check out good. Found defrost timer stuck in the freeze position, causing frost to accumulate over the evaporator. Manually rotated
... Read more
defrost timer to the 30min defrost cycle and system went into defrost. Ordered defrost timer and installed (part arrived in 3 days). Freezer works great again. Too bad I ended up throwing 400 dollars worth of meat away. the fix was very simple. Will definitely use PartSelect again. Thank you.
Read less
Was this helpful?
Thank you for voting!
loud noise fan blade broke,off balance
0 of 1 people
found this instruction helpful.
-
EDWIN from ELWOOD, IN
- Really Easy
- 15 - 30 mins
-
Nutdriver
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Was this helpful?
Thank you for voting!
Fridge was getting warm while the freezer was cold and running constantly.
0 of 2 people
found this instruction helpful.
-
Jeremiah from Northglenn, CO
- Easy
- Less than 15 mins
-
Nutdriver
After testing and eliminating the temperature control and the timer as the problem, I turned to the thermostat. I had to wait for the ice buildup to thaw and then could remove the rear freezer panel (this was the 3rd time: first, to discover the ice buildup causing the problem, second when it came back after a complete thaw and test the
... Read more
thermostat, and this time to put the Partselect thermostat back in). My thermostat was visibly damaged from water melting into ice and expanding the casing and eventually breaking one of the connections. I connected the thermostat connection wires (not recommended) to get by while ordering the part, which shipped faster than local repair places could get it from their warehouses, and at a fraction of the cost. I'm really impressed with partselect's fast service and all the knowledgable customers who have explained how they installed them. I now have an intimate knowledge of how my fridge works and saved hundreds in repair, or twice that in replacement. Thanks!
Read less
Was this helpful?
Thank you for voting!
refrigerator and freezer not cooling
1 of 5 people
found this instruction helpful.
-
Jimmie from Simms, TX
- Really Easy
- Less than 15 mins
-
Nutdriver
removed screws with from the back panel of the freezer; located defrost thermostat attached to coil with a metal clip; unplugged thermostat and replaced with the new one. Put every thing back together and it works perfectly.
Was this helpful?
Thank you for voting!
Freezer was building up ice. Running constantly.
0 of 3 people
found this instruction helpful.
-
eugene from norwalk, CT
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Parts Select is an excellent source for help and parts identification. I highly recomend them.
My first option was to replace the defrost timer.
After still getting ice and frost buildup in freezer I decided to replace the defrost thermostat.
Remove all shelves. Losen icemaker if applicable. Remove light cover and bulb. R ... Read more emove all screws securing rear vertical cover. Carefully move back panel, disconnect icemaker and bulb assembly. carefully remove styrofoam cover at upper left and remove defrost thermostat. I tested the thermostat and found it was defective. It would not close circuit after being placed in a working freezer. Reverse procedure to replace thermostat.
This solved the problem
My first option was to replace the defrost timer.
After still getting ice and frost buildup in freezer I decided to replace the defrost thermostat.
Remove all shelves. Losen icemaker if applicable. Remove light cover and bulb. R ... Read more emove all screws securing rear vertical cover. Carefully move back panel, disconnect icemaker and bulb assembly. carefully remove styrofoam cover at upper left and remove defrost thermostat. I tested the thermostat and found it was defective. It would not close circuit after being placed in a working freezer. Reverse procedure to replace thermostat.
This solved the problem
Read less
Was this helpful?
Thank you for voting!
thermostate stop working frozzen up
-
Augusto from Gretna, LA
- Really Easy
- Less than 15 mins
-
Nutdriver
just like the video show sa 1,2,3 yeaaa thanks
Was this helpful?
Thank you for voting!
refer quit cooling and so did freezer
-
jerry from petaluma, CA
- Really Easy
- Less than 15 mins
I replaced the defrost timer,defrost thermostat,and run cap.as it turned out the compressor went bad. I dont know the model because but the time I got this review I replaced the refer with a knew one . two weeks living out of coolers was so much fun !!!!!!!!
Was this helpful?
Thank you for voting!
Temp skyrocketed
-
Wayne from Chatham, IL
- Really Easy
- Less than 15 mins
Took out three shelves. Removed 9 screws with a battery powered drill with a phillip screwdriver bit. Popped off the thermostat like I had seen on the video. Put the new thermostat on. Replaced the two wires one at a time. Reassembled the unit. This was so quick that my wife told me to let her know when I wanted to fix the freezer. She wa
... Read more
s shocked that I had completed the job. I'd been in the garage less than 10 minutes. It has been six weeks. and the freezer is working perfectly.
Read less
Was this helpful?
Thank you for voting!
not cold enough
-
Gary from Hudson, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
per the video..easy installation....unfortunately the temperature did not improve. We still have a refrigerator temp in the upper freezer.....and a "cooler" in the refrigerator section
Was this helpful?
Thank you for voting!
freezer not cooling
-
Shawnda from Union City, PA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
inspected visible refrigeration lines for evidence of leaking, found nothing substantial that would cause concern, ordered capacitor and defrost thermostat simply because both are inexpensive parts and theoretically either could be causing the problem. Both parts were very simple to install especially since I am a semi-retired refrigerat
... Read more
ion man.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
the compressor capacitor overheated
-
Bart from goldsboro, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
it was great. I ordered the capacitor for my frigidaire frig and it arrived
in 3 days. plugged in the part to the compressor and my frig has been
working ever since. I spent 3 minutes ordering the part and 30 seconds
attaching it to the frig. Easy, very easy. saved myself a 75 dollar repair
visit. thanks
in 3 days. plugged in the part to the compressor and my frig has been
working ever since. I spent 3 minutes ordering the part and 30 seconds
attaching it to the frig. Easy, very easy. saved myself a 75 dollar repair
visit. thanks
Was this helpful?
Thank you for voting!
coils would freeze over not allowing air to circulate throughout freezer
-
robert from royal oaks, CA
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
replace thermostat and timer after defrosting and cleaning out freezer. I took less than 10 minutes and now freezer has a defrost cycle that eliminates frost buildup on the coils.
Other Parts Used:
Was this helpful?
Thank you for voting!
awasome
-
chris from springfield, GA
- Really Easy
- Less than 15 mins
After reading reviews I was not sure but I ordered part on Wensday in the AM and I had the correct part Thursday evening this company rocks thank you by the way i paid for regular shipping I will order again in a heartbeat
Was this helpful?
Thank you for voting!
Side rail for sliding shelf would not stay tight
-
Scott J from Westminster, CO
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
The sliding shelf side rail is held by three philips head screws that tighten into nut inserts. No amount of tightening would keep two of the three screws tight. I found that the nut inserts which are plastic and insert into the side of the freezer would pull loose, probably from years of overloading the sliding shelf basket. Ordered t
... Read more
wo nut inserts from PartSelect. 1. Remove three screws to remove shelf slide side rail. 2. Remove nut inserts to be replaced with needle nose pliers or reinsert screw a couple of turns and pull nut insert out with pliers. 3. Insert new nut inserts, position side rail, and tighten screws. Replace sliding shelf/basket.
Read less
Was this helpful?
Thank you for voting!