EIDW6105GS1A Electrolux Dishwasher - Instructions

Disconnect from power
Unscrewed 4 phillips screws from top of outer door.
Unscrewed 2 screws each siide of door.
Lower outer door section drops away.
Note wiring sequence on dispenser, then disconnect wires.
Unscrew 6 screws on dispenser and lift dispenser out.

Place new dispenser in place (note orient ... Read more ation), ann fasten in place with screws, remembering to replace wire retainer on left lower screw.
Reconnect wires to dispenser correctly.
Slide lower outer door over tabs and secure with the 4 side screws.
Ensure lower door is up under control panel and secure with the 4 top screws.

Fill dispenser with detergent, reconnect power and test run while enjoying a cup of tea in celebration of a job well done..

I was able to pull out the top basket were the glasses are put then I lined up the back and the center plastic clip an slid on the center spray arm. It took about 2 miniutes

The only difficultpart was to figure out how to remove the stainless cover from the door. Seems it slides upwards after screws are removed. After that it is self explainatory and goes back together in 5 minutes.

Replaced the entire top rack with spray bar.

No tools needed. Pull out old gasket. Clean the track. Ensure snug fit all across the track, use your thumb to push new gasket into the track firmly.

After turning of the power to dishwasher, I opened the door took of the two bottom screws on both sides of door. Closed the door and front panel just slide off. Then I took a picture of the dispenser to make use I could figure out how to put the wiring back together. Removed the six screws holding it in place and popped the dispenser out ... Read more . Easy .. popped new dispenser in and lightly put all six screws back in ,wired it back up after checking my photo. Closed the door ,slid front panel back on opened the door put the 4 screws back in that hold the front panel .Turned power back on and Boom!! All done.. Not bad for a girl...

removed the screws holding the door together, then removed the screws holding the dispenser to the interior door. replaced the wires and put the door back together

I got tired of having to replace the wheels. The wheels were essential for the tray to align along the tracks.Snap part into place

The video show a different model, the only difference is that the screws for the top part shouldn't be removed only the ones that hold the front. Replace the detergent dispenser once the cover is removed is easy. All works like brand new. Thanks.

Needed to replace detergent / rinse aid dispenser unit on the inside top of door.

1) Need to remove outer door cover / panel by removing just two (2) screws - bottom screws on lower side panel. Door panel will drop vertically 1" to remove it.

2) Mark and disconnect the four (4) wires connected to the dispenser unit ... Read more . The connections were so tight, it required pliers and a screw driver to loosen them.

3) Dispenser unit has four (4) screws holding it in place. Unscrew them and remove unit through door interior - this requires a bit of angling to get it out.

4) Position new unit through interior. Screw in place.

5) Re-attach four (4) wires in same sequence as disconnected.

6) Re-attach outer door cover. This is the most difficult part and really requires two people. It consistents of two sets of guide channels that most be aligned for the door panel to be secured re-attached.. Once aligned, the door cover must be moved vertically about an 1" and the screws re-attached.

Once replacement part arrived removed old broken item and snapped in new replacement item. Much easier to clean now. Thanks.

Went to the website, viewed the schematic and ordered the two gaskets that form the seal around the door and tub, Gaskets should be ordered as a set if you have a leak and suspect the door. We saw discoloration at the bottom edge of the tub gasket indicating that there was water seeping through out onto the floor.The gaskets install by ha ... Read more nd without the use of tools. Less than $100 in parts prevented the replacement of a $1,400 dishwasher.

Turned power supply off to dishwasher Opened door and removed screws holding font of door Unplugged soap dispenser and removed six screws. Popped out and installed new dispenser. Plugged wires into new dispenser and installed front of door. Easy

I removed and replacing the old dispenser.
This is located in the front door - dispenses both detergent and rinse agent - 2 compartments.

Requires disassembling the front door, removing the old dispenser, and installing the new dispenser, then re-assembling the door.

Open the front door
Place a folded blank ... Read more et or large pillow on the floor in front of the dishwasher.

Open the front door, so it resting on the blanket or pillow.
Remove the (12) star screws.
This will drop the front of the door onto the blanket or pillow.

Note:
As you remove the screws, the inner part of the door will attempt to close abruptly, because of the hinge springs, and the reduction in door weight, so be cautious.
There are several wire connections between the the 2 door sections.
Note that the latch assembly at the top of the door will fall out.

Slowly close the inner door, while lifting the outer door at the same time, and setting the outer door vertically.

Close the inner door section, while setting the outer section vertically. Having two people is helpful here.
Disconnect the 4 wires going to the dispenser - note the color and position of each wire before pulling.
The connectors have a release, so squeezing each connector is need for it to come off.

Remove the 6 Philips screws from the dispenser.
Pull the old dispenser out from the interior of the inner door section.
Install the new dispenser. Screw into place.
Reattach the 4 wires.

Reverse the door sections re-assembly.

The parts came in a timely manner and took about 15 minuets to replace with no tools.