EHS360-OF (EHS3600OF) Caloric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lower Bake Element burned out
0 of 2 people
found this instruction helpful.
-
Sharon from Sturgis, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
Two screws in the oven removed the old part and the wires unplugged from the unit. When the new part came in , it was plug and play. Plugged the wires into the new part, put part into holes in oven and screwed the screws back in place and we were ready to go. The part was here in record time. We ordered it on Sunday, it shipped out on
... Read more
Monday, it arrived on Tuesday and we were back in operation! Thanks for a really smooth repair experience!
Read less
Was this helpful?
Thank you for voting!
replace burner coil connector
0 of 2 people
found this instruction helpful.
-
dicky from mcrae, AR
- Really Easy
- Less than 15 mins
-
Screw drivers
Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be su
... Read more
re and disconnect power before starting!!
Read less
Was this helpful?
Thank you for voting!
element was busted
0 of 2 people
found this instruction helpful.
-
john from new port richey, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
shut off circut breaker. un pluged stove removed back panel disconected 2 wires on element. removed 1 screw that holds element in place pull out old element put in new reassemble
Was this helpful?
Thank you for voting!
Baking element overheated and split into two parts.
0 of 3 people
found this instruction helpful.
-
Derek from Gilford, NH
- Really Easy
- 15 - 30 mins
-
Screw drivers
First removed 2 screws holding in element housing at the back of the oven. Pulled element out and disconnected wire leads from the the element connection points. Reconnected leads from new element, pushed back into the back of oven and rescrewed into the oven housing. Done, very easy.
Was this helpful?
Thank you for voting!
hinge broken again
0 of 3 people
found this instruction helpful.
-
Russ from Milford, NE
- Really Easy
- Less than 15 mins
-
Screw drivers
r & r hinge. very poor pivot pin which leads to frequent replacement of hinge assembly, cheaply made, weak spot is hinge pin pivot rivet.
Was this helpful?
Thank you for voting!
Door gasket gotten hard
0 of 7 people
found this instruction helpful.
-
Richard from Pocomoke City, MD
- Really Easy
- 30 - 60 mins
-
Screw drivers
I took oven door apart and replaced old gasket with new one.
Was this helpful?
Thank you for voting!
Oven door hinge broken
-
Sherry from Mountain Ranch, CA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Discriptions provided by others in this section made it easy and there is little additional insight I can add. The part was delivered the next day. I don't reply to these requests for comments, as providing what I paid for is the expectation. But, this outfit did a good job.
Was this helpful?
Thank you for voting!
one burner that would not heat and others that would not out out much heat
-
Charles from Villa Ridge, MO
- Easy
- 30 - 60 mins
-
Screw drivers
I noticed that one of the burner blocks was completely burned and the others were corroded. I ordered blocks for all four burners. Installation was easy except for one block. The screw holding the bracket to the range top was completely corroded in place. I used a correct size easy-out, which is a left hand tap and drill, to remove th
... Read more
e screw. That took about five minutes, including tracking the easy-out down in one of my many toolboxes. The entire replacement of four blocks took about one and a half hours. Stove top cooks like new on all burners! The part kit had all the right parts and they fit like a glove!
Read less
Was this helpful?
Thank you for voting!
electric surface unit not working
-
vincent from Martinsville, VA
- Easy
- 30 - 60 mins
-
Screw drivers
After turning off circuit breaker to the stove, I removed all surface units , removed the 4 screws holding the top and lifted up. The plug in was burned out (the wire was burned). Look at the old plug-in so as to be able to match the new one and insert the pre- crimped end of wires into the block and the block into the metal holder that
... Read more
matches your old one. (The kit comes with 2 different metal holders)After this, cut out the old wires and wire nut the new wires with the stove wires. Put shrink wrap protector on the wire nuts and heat to shrink it tight.attach the block to the stove top and wa la its done. Very easy.
Read less
Was this helpful?
Thank you for voting!
Broiler heating element quit working
-
Rhonda from Great Bend, KS
- Really Easy
- 30 - 60 mins
-
Screw drivers
I had no trouble replacing the Broiler heating element, total time 30 minutes. Just had to pull the range out to unplug it and remove the back sheild of the range, then remove the two push on electrical connections. Then removed one screw holding the element to the inside of the oven, replaced with the new element, attached the connecti
... Read more
ons, but the back sheild back on and it was done.
Read less
Was this helpful?
Thank you for voting!
I had to replace the broiler element because it had burned up like a sparkler.
-
Georgia L from Coupeville, WA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
I read instructions and hints online. Then, I pulled the range out from between the cabinets and unplugged it (carefully). I used a small Philips head screwdriver to remove the 10 metal screws holding the large metal sheet on the back of the oven. Then I removed the 4 screws holding on the metal sheet on the upper level of the back of
... Read more
the range since it had to be removed to move back the big sheet metal away from the back. The large metal sheet has the power cord threaded through it on the bottom and I left that in place. I then removed the oven door by lifting it up off the hinges after I removed the screw on each side that held the door on the hinges. The door is quite heavy for a girl. I unscrewed the plate at the back of the broiler element, unhooked it from the hangers, and carefully pulled the connectors apart from the oven wiring and the dead broiler element. (Being completely unfamiliar with this kind of connector it took me some time to figure out they slid apart.) Following advice online I had used electrical tape to tape down the wires so they wouldn't slip backwards out of the oven. The new broiler element connectors slid smoothly and easily into the oven wires. I removed the electrical tape I had used as temporary holders, hung the element on the previous wire slings and removed the new wire slings for a backup. I screwed back the plate on the new element into the back of the oven wall. I used the part number orientation on the element to make certain I had it right side up. If I have to do this again it will be easy and take very little time. My biggest problem was getting the oven door back on because it was heavy for me and I was too short to be able to see what I was doing as I repeatedly tried to get the oven door and hinges aligned. Eventually the door was back on and screwed down. Everything that had been unscrewed was put back in place and screwed down tightly. The oven and broiler are working perfectly.
Read less
Was this helpful?
Thank you for voting!
Door wouldnt shut evenly.
-
David from Westlake, OH
- Difficult
- 1- 2 hours
-
Screw drivers
Ordered hinge, went to Sears bought some tools to finish manufacturing the hinge, tapped out the screw hole, installed the hinge.
Was this helpful?
Thank you for voting!
Surface burner block corroded
-
Teresa from Kasson, MN
- Really Easy
- Less than 15 mins
-
Screw drivers
It was a very easy fix. I followed the instructions that came with the kit and cut the original cable. Everything you need is in the kit; very few parts. Piece of cake and saved a lot of money an appliance repair person would have charged. This burner works better than the rest. I'm seriously considering replacing the other three blocks.
Was this helpful?
Thank you for voting!
Blocks were broken
-
James J from Sweet Grass, MT
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
The four kits arrived, use of a pliers and shink wrap and side cutters...strip wires, twist wires connect wire ties, shrink wrap...little fire, plug the elements...done...four in about ten minutes...Instructions in each package...no problem...very easy...saved twice the money or more...Thanks for the parts...recommend this site purchase..
... Read more
.parts arrived very timely...J. Iriwn
Read less
Was this helpful?
Thank you for voting!
Bottom baking element was not heating oven to proper temperature
-
Deanna from Blue Mounds, WI
- Really Easy
- Less than 15 mins
-
Screw drivers
Unscrewed 2 screws holding the bracket on the back of the stove and disconnected the wires from the two clips. Removed back element, connected new elements & replaced screws to back inside wall of oven. Works like brand new!!
Was this helpful?
Thank you for voting!