EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

EHS360-OF (EHS3600OF) Caloric Range - Instructions

All Instructions for the EHS360-OF
76 - 90 of 148

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
burner connector - bad connection
0 of 1 people found this instruction helpful.
  • Terry from Grand Forks, ND
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed burner and tray. Removed burner connector from stove top using screw driver.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.
Was this helpful?
Thank you for voting!
range top burners not heating reliably
0 of 1 people found this instruction helpful.
  • Roy from Moore, OK
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed the original burner element sockets and replaced with parts provided in kit. Instructions were simple and easy to follow, problem completely solved in 20 mins!
Was this helpful?
Thank you for voting!
Sparks where the heating element plugs into the stovetop
0 of 1 people found this instruction helpful.
  • Martin from Sayre, PA
  • Easy
  • 15 - 30 mins
  • Screw drivers
The directions were very clear. I removed the heating element, detached the plug-in block by unscrewing the screw, then cut the wires about 3 inches from the block. I put the shrink-wrap collars around the wires leading to the new block, then attached the wires to the cut ends of the wires leading to the back of the stove, using the con nectors provided in the kit. I couldn't get the collars to shrink as much as shown in the picture. I attached the new block to the stove top using the screw, plugged in the heating element, and it worked!
So the instructions were good, and the heating element is now working. The only problem was the heat shrink collars that go around the connectors: I couldn't get them to shrink much, but that doesn't seem to matter.
Was this helpful?
Thank you for voting!
elemenent caught on fire
0 of 1 people found this instruction helpful.
  • John from Franklin, MA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
my wife did the the job and it was that easy. she took out two screws sliped the wires off put the two wires back on and put the screws in . She is a bank teller and teachers water aerobics
Was this helpful?
Thank you for voting!
lower heat element would not get to temperature
0 of 1 people found this instruction helpful.
  • Titus from Madison, WI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Slide stove out and unplug. Using nut driver (phillips screw driver would work fine) remove screws securing back panel. Remove back panel. Pull off wires from heating element. I made a lose knot on left wire so I could install as removed without confusion - sometimes it matters. Removed 2 screws securing element inside the oven. I ins talled everything as it was - oven works great. I saved over $100 and my wife thinks I'm a genius. Hardest part was cleaning accumulated mess behind the stove.
Was this helpful?
Thank you for voting!
burner wouldn`t stay hot.
0 of 1 people found this instruction helpful.
  • Cary from Gilbertsville, PA
  • Easy
  • 15 - 30 mins
  • Screw drivers
First I lifted the cooktop out of the countertop & removed the screws so I could access under the burners.Then I cut the wires for the old plug-in block & then stripped the wires.Next I connected the new wires with the wire nuts & then used a lighter to shrink wrap the wire nuts.Then I screwed in the new block & re-installed the screws fo r the cooktop.I put in the new burner & it worked just like new.
Was this helpful?
Thank you for voting!
Worn out terminal block
0 of 1 people found this instruction helpful.
  • John from Brookings, OR
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Turned off the power to the stove. Removed the 'burners' and 'burner' trays. Removed the screw that secured the bad block. Lifted the top of the stove. Cut the two wires to the bad block., stripped the wires about 1/2", slipped the shrink tube over the wires. Connected the new block with two porcelan wire nuts. slipped the shrink tube ove r the wirenuts and heated it with a lighter. Closed the top and secured the terminal block clip with a screw. Turned the power back on: voila!

All the necessary parts came in the repair kit, delivery was timely. Very easy project.
Was this helpful?
Thank you for voting!
contacts in plug-in block badly burned & oxidized
0 of 1 people found this instruction helpful.
  • william from port st lucie, FL
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
First I removed the one screw that held the element in place. I then pulled the element out about 3 inches and cut the two wires...)
Assembled the block parts.
Installed shrink sleve and applied wire nuts to electrical connection to 2 wires then shrunk the sleve.
Did the above procedure for 2 heating elements.
They w ork very well now.
Was this helpful?
Thank you for voting!
Was baking brownies and all the sudden the heating element started sparking, flaming, and looking like a welding rod.
0 of 1 people found this instruction helpful.
  • WAYNE from FERGUSON, MO
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then I reconnected the wires to the new element and screwed it in to the oven back. Simple and inexpensive fix.
Was this helpful?
Thank you for voting!
Broken oven door hinges
0 of 1 people found this instruction helpful.
  • James from Brookline, MA
  • A Bit Difficult
  • More than 2 hours
  • Screw drivers
Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old hinges and installing the new ones.
Was this helpful?
Thank you for voting!
cooking element shorted out and did not heat.
0 of 1 people found this instruction helpful.
  • Carolyn from Fyffe, AL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I had bought the 1st set of plug-in blocks at lowes, They were the only type they had the univeral ones! They did not hold the elements plug tight enough and half the time they would have to be punshed in more then they would snap and sizzle- I ordere the newer style and they have done great they are better made and heavier metal parts- they elements fit in snuggly and do not sizzle or nor do I have to push the element in. This stove is 35 years old and I have replaced most everything on it. But it's still cooking...
Was this helpful?
Thank you for voting!
Wire broken going to one electric plug for burner
0 of 1 people found this instruction helpful.
  • John from Shelby Township, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Replace the connector and bracket, spliced the wires, put heat to the schrink wrap and I was done.
Was this helpful?
Thank you for voting!
no heat from burner
0 of 1 people found this instruction helpful.
  • George from ST. Charles, MO
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I raised the stove top, read the instructions to my son while he did the work, then I lowered the stove top, installed the burner, and it worked like magic.
Was this helpful?
Thank you for voting!
The bake element shorted out and burned up.
0 of 1 people found this instruction helpful.
  • Lewis from San Diego, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
This repair took less than 5 minutes, literally! Two screws released the element, then unplugged it from two connectors. Then plugged in the new unit and screwed it into place. Cheap and easy!
Was this helpful?
Thank you for voting!
Burner Would Not Heat
0 of 1 people found this instruction helpful.
  • David from Toledo, OH
  • Really Easy
  • Less than 15 mins
  • Screw drivers
One screw taken out, 2 wires switched, new part & screw put in. Burner like new!
Was this helpful?
Thank you for voting!
All Instructions for the EHS360-OF
76 - 90 of 148