EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

EHS335 Caloric Range - Instructions

All Instructions for the EHS335
61 - 75 of 127

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
holder burnt
0 of 1 people found this instruction helpful.
  • Paul from lewiston, ME
  • Easy
  • 15 - 30 mins
  • Screw drivers
First I removed the one screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Was this helpful?
Thank you for voting!
contacts in plug-in block badly burned & oxidized
0 of 1 people found this instruction helpful.
  • william from port st lucie, FL
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
First I removed the one screw that held the element in place. I then pulled the element out about 3 inches and cut the two wires...)
Assembled the block parts.
Installed shrink sleve and applied wire nuts to electrical connection to 2 wires then shrunk the sleve.
Did the above procedure for 2 heating elements.
They w ork very well now.
Was this helpful?
Thank you for voting!
burner connector - bad connection
0 of 1 people found this instruction helpful.
  • Terry from Grand Forks, ND
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed burner and tray. Removed burner connector from stove top using screw driver.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.
Was this helpful?
Thank you for voting!
burner wouldn`t stay hot.
0 of 1 people found this instruction helpful.
  • Cary from Gilbertsville, PA
  • Easy
  • 15 - 30 mins
  • Screw drivers
First I lifted the cooktop out of the countertop & removed the screws so I could access under the burners.Then I cut the wires for the old plug-in block & then stripped the wires.Next I connected the new wires with the wire nuts & then used a lighter to shrink wrap the wire nuts.Then I screwed in the new block & re-installed the screws fo r the cooktop.I put in the new burner & it worked just like new.
Was this helpful?
Thank you for voting!
Worn out terminal block
0 of 1 people found this instruction helpful.
  • John from Brookings, OR
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Turned off the power to the stove. Removed the 'burners' and 'burner' trays. Removed the screw that secured the bad block. Lifted the top of the stove. Cut the two wires to the bad block., stripped the wires about 1/2", slipped the shrink tube over the wires. Connected the new block with two porcelan wire nuts. slipped the shrink tube ove r the wirenuts and heated it with a lighter. Closed the top and secured the terminal block clip with a screw. Turned the power back on: voila!

All the necessary parts came in the repair kit, delivery was timely. Very easy project.
Was this helpful?
Thank you for voting!
Sparks where the heating element plugs into the stovetop
0 of 1 people found this instruction helpful.
  • Martin from Sayre, PA
  • Easy
  • 15 - 30 mins
  • Screw drivers
The directions were very clear. I removed the heating element, detached the plug-in block by unscrewing the screw, then cut the wires about 3 inches from the block. I put the shrink-wrap collars around the wires leading to the new block, then attached the wires to the cut ends of the wires leading to the back of the stove, using the con nectors provided in the kit. I couldn't get the collars to shrink as much as shown in the picture. I attached the new block to the stove top using the screw, plugged in the heating element, and it worked!
So the instructions were good, and the heating element is now working. The only problem was the heat shrink collars that go around the connectors: I couldn't get them to shrink much, but that doesn't seem to matter.
Was this helpful?
Thank you for voting!
Right front surface burner did not work due to broken burner plug in wire harness.
0 of 1 people found this instruction helpful.
  • Raymond from Rock Hill, SC
  • Easy
  • 15 - 30 mins
  • Screw drivers
Cut power. Removed four attaching screws and raised stove top. Cut two wires of existing burner plug. Used existing plug to select correct plug configuration from parts in kit. Attached new plug and wires to wiring harness using connectors and heat-shrink tubing supplied with kit. Used hair dryer to shrink tubing on connectors. Closed up stove. Restored power. Burner now functional.
Was this helpful?
Thank you for voting!
Light burned out in upper oven
0 of 1 people found this instruction helpful.
  • Shirley from Las Vegas, NV
  • Really Easy
  • Less than 15 mins
Screwed in light bulb and glass protector
Was this helpful?
Thank you for voting!
replaced oven lightbulb
0 of 1 people found this instruction helpful.
  • peggy ann from forest city, NC
  • Really Easy
  • Less than 15 mins
very easy
Was this helpful?
Thank you for voting!
Bulb Replacement
0 of 2 people found this instruction helpful.
  • Judith from Phoenix, AZ
  • Really Easy
  • Less than 15 mins
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this helpful?
Thank you for voting!
replace burner coil connector
0 of 2 people found this instruction helpful.
  • dicky from mcrae, AR
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be su re and disconnect power before starting!!
Was this helpful?
Thank you for voting!
large burners not working
0 of 2 people found this instruction helpful.
  • Greg from Versailles, IN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so yo u have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.
Was this helpful?
Thank you for voting!
replace the cook stove's drip bowls instead of cleaning them
  • Dallas from Arlington, TX
  • Really Easy
  • Less than 15 mins
I removed the burners and then the older drip bowls of the cook stove--and then I put on the new drip bowls and put back on the burners. My mechanical skills were sufficient for the replacement of the drip bowls.
Was this helpful?
Thank you for voting!
The surface burner socket that the burner plugs into melted.
  • Gary from Chesapeake, VA
  • Easy
  • Less than 15 mins
  • Screw drivers
Cut the old wires off, removed the screw holding the clamp, installed the new parts. Problems I encountered were the wire nuts. They were too small for the wire gage of the replacement part and the original oven. I had larger wire nuts in my workshop. Also, why so many extra parts like the shrink wrap tubing, two metal clamps to hold t he socket, etc.
Was this helpful?
Thank you for voting!
I needed to replace to two 8* drip bowls on the kitchen range
  • Dallas from Arlington, TX
  • Really Easy
  • Less than 15 mins
(a) I took out (and threw away) two stained 8* chrome drip bowls on my kitchen range; (b) ti put in two new 8" chrome drip bowls on my kitchen range. I'm pleased that I was equal to the task.
Was this helpful?
Thank you for voting!
All Instructions for the EHS335
61 - 75 of 127