EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

EHS335 Caloric Range - Instructions

All Instructions for the EHS335
46 - 60 of 127

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drip pans needed to be replaced
1 of 2 people found this instruction helpful.
  • Mark from ROSENBERG, TX
  • Very Easy
  • Less than 15 mins
1) removed heating elements. 2) removed drip pans. 3) installed new drip pans. 4) reinstalled heating elements
Was this helpful?
Thank you for voting!
My drip pans were in bad shape
2 of 5 people found this instruction helpful.
  • Sandra from Oldsmar, FL
  • Really Easy
  • Less than 15 mins
I removed the old and repaced with new. I never ordered anything one day and got it the next. I'm impressed
Was this helpful?
Thank you for voting!
burned oven bulb
3 of 9 people found this instruction helpful.
  • Ivanka from Atlantra, GA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh t bulb in was not the problem.
Was this helpful?
Thank you for voting!
2 of the burners were not working arching and smoking
1 of 3 people found this instruction helpful.
  • Tina from Laurel, MT
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Time was do to the fact that I replaced two elements! I turned off the power to the braker box, unplugged the stove and removed the screw holding the element plug in, removed the part, and cut the wires where they were clean looking (not damaged by smoke or the arch) I then stripped the wire and took the new part and twisted the parts t ogether with the caps and then put the heat shrink on and used the blow dryer on them, attached the part to the bracket and screwed it to the hood of the stove plugged the burner in, plugged in the oven and turned on the power tested it worked, did the same for the next burner and yes mind you I am a woman it was very easy to do.
Was this helpful?
Thank you for voting!
cooking element shorted out and did not heat.
0 of 1 people found this instruction helpful.
  • Carolyn from Fyffe, AL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I had bought the 1st set of plug-in blocks at lowes, They were the only type they had the univeral ones! They did not hold the elements plug tight enough and half the time they would have to be punshed in more then they would snap and sizzle- I ordere the newer style and they have done great they are better made and heavier metal parts- they elements fit in snuggly and do not sizzle or nor do I have to push the element in. This stove is 35 years old and I have replaced most everything on it. But it's still cooking...
Was this helpful?
Thank you for voting!
oven light burnt out
3 of 10 people found this instruction helpful.
  • William from Schwenksville, PA
  • Easy
  • Less than 15 mins
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this helpful?
Thank you for voting!
contacts had gotten burnt out/blackened with age so burner was intermittent.
0 of 1 people found this instruction helpful.
  • john from reading, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
lifted the cover, unscrewed the ceramic wire fastners, put the new part in, and voila, job done and working perfectly
Was this helpful?
Thank you for voting!
Wire broken off plug in block
0 of 1 people found this instruction helpful.
  • Robert from Phillipsburg, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed old block , cut off wires , used new wire nuts, heat shrink , supplied with parts , job done lowered range top went fishing ...
Was this helpful?
Thank you for voting!
Bowl -Drip and gasket
0 of 1 people found this instruction helpful.
  • Walid from Worcester, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
it was relay easy when you get the right pats .so
Thanks for .
PART Select.
Best regard .
Walid
Was this helpful?
Thank you for voting!
Burner Would Not Heat
0 of 1 people found this instruction helpful.
  • David from Toledo, OH
  • Really Easy
  • Less than 15 mins
  • Screw drivers
One screw taken out, 2 wires switched, new part & screw put in. Burner like new!
Was this helpful?
Thank you for voting!
Wire broken going to one electric plug for burner
0 of 1 people found this instruction helpful.
  • John from Shelby Township, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Replace the connector and bracket, spliced the wires, put heat to the schrink wrap and I was done.
Was this helpful?
Thank you for voting!
no heat from burner
0 of 1 people found this instruction helpful.
  • George from ST. Charles, MO
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I raised the stove top, read the instructions to my son while he did the work, then I lowered the stove top, installed the burner, and it worked like magic.
Was this helpful?
Thank you for voting!
light bulb went out in my oven
2 of 7 people found this instruction helpful.
  • Janet from Ada, MI
  • Really Easy
  • Less than 15 mins
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
Was this helpful?
Thank you for voting!
range top burners not heating reliably
0 of 1 people found this instruction helpful.
  • Roy from Moore, OK
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed the original burner element sockets and replaced with parts provided in kit. Instructions were simple and easy to follow, problem completely solved in 20 mins!
Was this helpful?
Thank you for voting!
Block broke
1 of 4 people found this instruction helpful.
  • Edward from Crimora, VA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done
Was this helpful?
Thank you for voting!
All Instructions for the EHS335
46 - 60 of 127