EHD397 Caloric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bulb Replacement
0 of 2 people
found this instruction helpful.
-
Judith from Phoenix, AZ
- Really Easy
- Less than 15 mins
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this helpful?
Thank you for voting!
Old surface element burned out.
0 of 2 people
found this instruction helpful.
-
Royce from Rio Rancho, NM
- Really Easy
- Less than 15 mins
I ordered and received the replacement element, then unplugged the old one and plugged in the new one.
Job done.
Job done.
Was this helpful?
Thank you for voting!
replace burner coil connector
0 of 2 people
found this instruction helpful.
-
dicky from mcrae, AR
- Really Easy
- Less than 15 mins
-
Screw drivers
Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be su
... Read more
re and disconnect power before starting!!
Read less
Was this helpful?
Thank you for voting!
Burners quit working
-
Brenda from Brazoria, TX
- Really Easy
- Less than 15 mins
Bought two new replacement burners,they work great!
Other Parts Used:
Was this helpful?
Thank you for voting!
Replace top oven seal
-
Linda from Oxnard, CA
- Really Easy
- Less than 15 mins
This is a simple replacement. The hardest part was that I had to shorten the seal because it comes 15 to 17 inches. So it needed to be shortened to properly fit. I cut the seal to fit, then took the metal hook on the end and super glued it to the cut end. I put a weight on it to make sure
Was this helpful?
Thank you for voting!
burner not working
-
gene from kent, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
burner was shorting out replaced part works great
Was this helpful?
Thank you for voting!
burner would not heat up the connection was bad
-
Earl from Union Mills, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.
Was this helpful?
Thank you for voting!
Burner was slow heating at times. Moved back burner to front still same thing.
-
Gail M from Lockport, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
Unscrewed screw holding bracket. Used side cutters to cut wires. Replaced the bracket, put the shrink wrap on wires, twisted wires together and held with wire caps. Shrunk the wrap with lighter. I'm a 67 year old female.. No problems.
Was this helpful?
Thank you for voting!
Burner keep coming on and going off had a short in burner plug-in block.
-
Judith from Staunton, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
Turned off stove breaker. Unscrewed burner from stove top, took out burner and spill pan. Lifted top of stove, cut the wire as instructed and put all parts together as instructed. Placed everything back together as instructed. I did it myself!
Was this helpful?
Thank you for voting!
Light bulb failure
-
Grant from Alexandria, VA
- Really Easy
- Less than 15 mins
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this helpful?
Thank you for voting!
part of original burner not working
-
SUSAN K from SEDALIA, MO
- Really Easy
- Less than 15 mins
slide new burner in slot and turned on stove. Worked perfectly.
Was this helpful?
Thank you for voting!
The drip pans needed replacing.
-
Alison from Carnation, WA
- Really Easy
- Less than 15 mins
Put in the new drip pan -- which are really nice shiny ones.
Other Parts Used:
Was this helpful?
Thank you for voting!
Dirty drip bowls
-
Paul from Carnegie, PA
- Really Easy
- Less than 15 mins
Just remove old bowls from range top and put new ones. That is all ... just super simple! :)
Other Parts Used:
Was this helpful?
Thank you for voting!
Dirty drip bowl
-
Paul from Carnegie, PA
- Really Easy
- Less than 15 mins
Remove old drip bowl from the range and put a new one back.
Was this helpful?
Thank you for voting!
Drip bowls were all rusted.
-
Robin from Seneca, SC
- Really Easy
- Less than 15 mins
Removed old rusted drip bowls and put in the new ones. Very easy to do and needed no tools. It made my 25 plus Jenn Air look new again!
Other Parts Used:
Was this helpful?
Thank you for voting!