ECKMF64 Whirlpool Ice Maker - Instructions

Disconncted power, pulled plug on disconnect, loosened 3 ice maker attach screws, removed ice maker. carefully removed old broken part, to understand reasembly. Reinstalled new water fill & bearing part.. hung icemaker and tightened attach screws. Reattached electrical plug.. turned on power, it all worked. .took about 45 min to remove ... Read more , 15 min to reinstall. Right tools needed re disassembly AND ASSEMBLY

Watched a video on YouTube on how to replace the icemaker control assembly. The video showed unplugging power, turning off the water supply, and removing the entire ice maker from the freezer. After watching the video several times, I unplugged the refrigerator but did not turn off the water supply. I did not remover the entire ice mak ... Read more er from the freezer, but I did remove the wire shut-off arm. After that, I pried off front cover of the control assembly. The control assembly is held in place by 3 Phillips screws; I removed the screws, removed the icemaker control assembly, replaced the assembly with the new one, replace the cover and wire shut-off arm, and plugged the refrigerator back into the wall. Had ice in about an hour (seemed the system had a little delay before deciding to go to work!).

It took both me and my wife! One of the new parts we recieved was broke so we took the part off of the one that didn't work.

Unplug the fridge. Used the screw driver to remove the motor. Easy. Now putting the new one in was difficult because it has to line up exactly.
Thats what took 15 minutes but after me and my wife w ... Read more orked on it, we had a bucket of ice by morning!
We only knew how to do what we did because of reading these messages on this site. It came with no directions.

Easy, just removed the ice dispenser and the left support for the dispenser so I could get to the bottom screw easier. Three screws held the mold in place. The bottom screw had to be removed completely, but I just loosened the two top screws and lifted the mold out away from the wall and then disconnected the wiring. The end cover snapped ... Read more of easy with a screw driver. I then removed the three screws holding the motor. then pulled the motor off.(the next square part under the cover. I did this before I realized that I could use a small screw driver and stick it into the holes to remove the mold and not mess with the outer screws. After I removed the mold, I replaced the new mold into position, without putting the white forky looking part back on so I had to take the two screws out and put the part in place before attaching the motor back to the mold. Everything went back together just like a charm. The ice maker is working good, easy job. Gone golfing now.

I unpacked the motor and looked at how it was supposed to go in. I removed on screw in the right rear of the ice maker. Pushed a tab on the left of the ice maker. Removed the entire assembly and unhooked the electrical part of the ice make. unscrewed the three screws holding the motor in place and replaced the motor. Put everything i ... Read more n back together and in 15 minutes the familar sound of the ice maker could be heard.

There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.

My ice maker just stopped filling with water one day and after some troubleshooting, I found that a chunk of ice had built up in the tube between the water supply line and freezer. I took the ice maker out (Don't touch the heating element...it really hurts) and defrosted the ice obstruction by injecting hot water into the tube to melt the ... Read more ice. I used a new plastic syringe you get with an infant over the counter drug and a bucket to catch the water. I noticed the ice cube mold was peeling and decided to replace the mold. The mold is an easy replacement as long as you remember how you took it apart. My mold had some glue or compound stuck to the side that kept me from getting the mold flush against the motor assembly housing so I had to uncrew and scrape that gunk off and reattached. Other than that, there was nothing to it. Now the ice maker is good for another 8 years.

remove the wiring cover, pulled out the ice maker shelf, unpluged the wiring. Once out I removed the control module cover and remove 3 screws and pulled out the old control module. I pushed on the new control module and reattached the 3 screws, attached the module cover and plugged wiring in, slide back into the freezer track, installed ... Read more wiring cover and screw- 15 minuits tops

After removing the ice maker, I guessed that the moter could be the problem,bought new part I installed it and held my breath.thankfully that was it.thanks to parts select I saved a lot of money doing it myself.

Removed icemaker by first removing the nutscrew that holds the cover to the electrical connection in place. Next, I removed the door then slid the icemaker out and diconnected the electrical connector. With the icemaker out, I R&R'ed the motor assy , reconnected the electrical, and slid the icemaker back in place. Next, I replaced the doo ... Read more r, turned the icemaker switch on and waited. In about 30 minutes I heard the water being injected into the icemaker, and soon there was ice. The repair was easy and inexpensive. Tx to Partselect which I found on Google.

turned water off to ice maker unpluged fridg while doing repair which was such short time everything was ok removed 3 1/4 hex screws holding ice maker in position while holding ice maker in hand unpluged wiring connection for it removed old ice mold which coating had come off of which was very simple 2 philips screws which are recessed on ... Read more control unit then gently wiggle assembly apart paying attention to how all the tray parts went together then reinstalling same way as they were remove very simple repair anyone should be able to do

Followed video lnstructions which were very good. Have used your web site in the past and will continue to purchase products. Thanks.

I took the front panel off the ice maker. Found the contacts on control board were burnt. I called Partselect, told them my model # and they directed me to a new control panel. 4 screws later I had part back on and ice makin.
Thanks Partselect!

John Long

removed front cover installed gearbox then attached lift arm plugged in frig turned on h2o and now i have plenty of ice ! ordered part on Saturday got part on monday in the mail and had ice by supper what a great place to shop and the service was great and parts made easy to find on the website. thank you very much! I will refer your bus ... Read more iness to all my friends.

unpluged the refrigerator, remove three screws holding ice maker in place, disconnected wire clip, removed front of icemaker by relaesing two clips holding it in place. the module and motor assembly are held in place with three screws. put the icemaker together and replaced it in freezer, and pluged the cord back in. the icemaker started ... Read more making ice in about 15 minutes. very easy fix