EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

DV206AESXAC Samsung Dryer - Instructions

All Instructions for the DV206AESXAC
1 - 11 of 11

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The dryer turned on but the drum did not move when you pressed start even though It started it cycles.
42 of 79 people found this instruction helpful.
  • Christopher from SUGARLOAF, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I YouTube it and there’s a step by step process on how to do it, took maybe 30 mins. If I can so can you
Was this helpful?
Thank you for voting!
Dryer stopped heating
6 of 8 people found this instruction helpful.
  • Mark from WEST SUNBURY, PA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I purchased wholesale heater element with sensors. Couple wires and bolts to attach. Trickiest part is disassembling the dryer to remove the old heating unit. You-tube it; it's gold.
Was this helpful?
Thank you for voting!
Door seal was torn and falling apart
3 of 3 people found this instruction helpful.
  • Jon from San Diego, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Separated the outer door from inner door, removed glass globe. Replaced the seal

Reassembled
Was this helpful?
Thank you for voting!
Heating coil went ..
2 of 2 people found this instruction helpful.
  • Peter from TROY, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Dryer was pretty easy to disassemble. The video helped, especially when re-routing the drive belt. Would definitely but from Parts Select again!
Was this helpful?
Thank you for voting!
The dryer was running just fine in all areas except there was no heat. The vent line was not plugged.
2 of 2 people found this instruction helpful.
  • David from RENTON, WA
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers
I firstly over-ordered parts. The general guidance is check one part and replace if bad, then check the next, etc. I only wanted to do the disassembly once so I ordered all the parts which were involved with generating heat. Turned out the heater duct assembly came with the thermal fuse and thermistor already installed, in addition to the heating element. Once I had the parts, I watched the video which was identified in my parts order. Then I started disassembly. I put screws from each step into their own little container so there was no mixing them up. Everything went exactly as shown in the video, except for the front panel containing the control board. My dryer was slightly different, but still easy to get out. When I had the drum out, the heater duct assemble was easy to remove, one screw only. I transferred connecters from the old duct to the new one-at-a-time to make sure there were no mistakes, then installed the new one with the single screw. Re-assembly went quickly. I plugged it in and, with some hesitation, set it to a short timed cycle and started it. After a few minutes, I hit pause and stuck my hand in the drum and it was warm! The dryer has continued to work since. Repair successful!
Was this helpful?
Thank you for voting!
Drum stopped turning.
2 of 3 people found this instruction helpful.
  • Dequince Atkinson from PLATTSBURG, MO
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Followed the video on the website and finished it in a short time. Now it works like a new dryer.
Was this helpful?
Thank you for voting!
Drum don’t turn
3 of 6 people found this instruction helpful.
  • Orlando from LAWRENCEVILLE, GA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Follow the video instructions.
Was this helpful?
Thank you for voting!
Original belt broke after nylon tension pulley bearing froze.
2 of 4 people found this instruction helpful.
  • John m from GRAPEVIEW, WA
  • Really Easy
  • 30 - 60 mins
Thank you
partselect.com for a much better heavy duty belt than the original. Way over priced, but well worth it. After watching the video & following it step-by-step, I now have a perfectly running dryer. P.S. don't forget to plug back in the (3) wire harnesses. The entire experience was a great feeling of accomplishment. Thank s again partselect.com
Was this helpful?
Thank you for voting!
high limit thermostat and heating element were bad.
1 of 2 people found this instruction helpful.
  • Paul from FIRESTONE, CO
  • Easy
  • 1- 2 hours
  • Screw drivers, Socket set
I would like to direct the attention to PartSelect instead of my repair. They were awesome in helping me to get my parts. I had called, a few minutes after the deadline for overnight shipping, the gentleman helping me, pushed the order through and I got my parts the next day, allowing me to repair my dryer. I have ordered several parts , for several different appliances, (all Samsung) and PartSelect has always come through for me. Excellent Customer Service!!
P.S. Don't buy Samsung appliances unless you want to get good at repairing them!
Was this helpful?
Thank you for voting!
Drier did not turn it was not the belt
1 of 3 people found this instruction helpful.
  • Anthony from FLORAL PARK, NY
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I still had to take it apart there was a small sock stuck in the fan that blowes the lent out my wife left the lent filter out one time. Your video was a great help. I'm a mechanic and it was easy thanks Anthony Ratto [email protected]
Was this helpful?
Thank you for voting!
All Instructions for the DV206AESXAC
1 - 11 of 11