DLL2550PE Hotpoint Dryer - Instructions

Backwards to start- here's the correct way.Disconnect power and vent hose-tip onto front-remove bottom plate allowing access to bottom of dryer and the belt pulleys-remove the small plate in center and under that is a C-clip holding the drum shaft in place-remove the clip and washer-sit dryer upright - open the door and remove the 4 scre ... Read more ws under the upper lip which hold the top of the dryer in place-lift up top and secure or have someone hold it up.-inside the top front on both sides are 2 screws per side and there are 2 screws at the bottom under the kick area, remove all 6 of these screws and the front of the dryer will come off-watch the wires-with the front off you can pull the drum forward to allow installing the new belt. - hold the new belt in place with a couple of pieces of tape-reverse the procedure to put drum back together and then thread the new belt onto the drive pulley and under the idler tension pulley.- reinstall back plate, vent hose, power and you're ready to go have a beer.

First unscrew the two screws at top to disconnect the control panel. Lay unit on the back. Remove door(be careful not to lose washers and hinges). Remove four screws to lift off top. Wiggle drum, slip belt over drum. Replace door, then put Four screws back in place.Stand unit upright.Remove back panel, you should see belt hanging.Pulley w ... Read more heel is in front of you.Follow instuctions sent with pulley wheel.Reattach you're ready to roll, make sure you sllip the belt on the drum until the drum spins.

Removed Front of Machine, removed access panel on back of machine, reassembled after installing belt and cleaning out machine. Pretty Easy, hardest part is getting around the front of the drum.This machine has been going since 1978. 31 years, 2nd replacement belt and thats all, not bad, the washer that was bought at the same time went aro ... Read more und 6 years ago, havent had the same luck, since then, two machines and the latest one is giving me problems already. They dont make them like they used to.

Replaced gas igniter The part came a day after I ordered it. I really liked the speed of delivery.

Easy as steps 1 & 2, remove old filter & replace w/ new.
It fit perfectly which was my main concern, as I could not tell from picture if the length was correct.
I am very pleased w/ product & it works just fine..

I called customer Servioce and they helped me with the corrfect part number

1. removed old switch 2.wrote model # 3. went to web site found part 4. ordered part 5 part came in 2 days 6. installed part in 15 min. works like new saved over 95.00 thanks ed

Pulled the old filter out of the door of the dryer and then removed the new filter from the shipping box and took the new Lint filter out of the packaging and then slipped the new lint filter into the lint filter holder and started up the dryer and away we went on our happy way. Thanks to all of you guys and gals at PARTS SELECT.

Took the old filter out and inserted the new filter which was a near perfect fit on a 36 year old dryed that is still kicking! Delivery of the part was less than 24 hours after ordering over the phone. Thanks1

Finding parts for very old appliances (that otherwise are working great!) was very much appreciated...lint filters are very very important and this one has served it's useful life. Thank you for such an amazing parts inventory, good prices, and FAST delivery!

This wan't a repair. It was simply a part replacement for a part that was easily accessable. I was more pleased at the fact that I could find the part considering how old the dryer is.

I just replaced the old filter with the new filter and I wonder why I didn't order a replacement filter sooner.

Found and ordered igniter on Tuesday. Part arrived on Friday. Took about 5 minutes to remove old igniter and install new one. Took about 5 minutes. Dryer works like new again. Hopefully it will last for another 16 years!

place inside of dryer

My Daughter did it for me .

Unplug the dryer, turn off the gas. Opened the lower front door panel. She disconnected the gas pipe from the igniter assembly. Then She removed the two screws holding the assmb. Then she removed the wire from the front of the assmb. and the white and black wire from the back of the unit. remove th ... Read more e old igniter put in the new one put it back together.