DDT575SSF0SS General Electric Dishwasher - Instructions

My heating coil was not working so naturally I thought I needed a new coil and ordered one accordingly. During the time it took to ship to me, I did more research and people suggested testing the coil with and ohmmeter for resistance as often times the coil is fine and it is the flood switch that is the problem. I got an ohmmeter and chec ... Read more ked the old coil and it returned readings that were just fine (btw 15-30), so I returned the coil and ordered this flood switch.

Anyone reading this debating between buying the coil and switch can save themselves a lot of trouble/time/money by removing the coil and testing it first.

The installation of the flood switch is fairly simple. There's a great video on Youtube for it (titled "GE Dishwasher not Drying Dishes - How to Replace Bad Flood Switch:), so I won't walk through the step-by-step on it.

However, one word of advice is to be careful when installing so that you don't let the o-ring on the switch slide down the connector/wire once you connect them or you'll get a slow leak into the catch pan at the bottom.

Also, if this if your first repair on a GE Dishwasher then get to know the unit while you have it pulled out. It won't be your last repair based on my experience...

The repair made it necessary to remove the door of the dishwasher. Removing the door seemed to be a daunting task, but after watching a YouTube video I made myself aware of the necessary steps to complete the task.

- After turning off the power to the dishwasher, I removed the kickplate panel, this gave access the wiring going ... Read more to the defective board, which I unplugged.
- Removed the screws securing the dishwasher to the counter, these are located at the top of the machine and are accessible by opening the dishwasher door.
- Pull the dishwasher forward a few inches.
- On each side of the door is a spring loaded device that holds the door from falling open when not latched. They can be identified as white plastic items with a cable connected to them. Once removed take care to not allow the door to fall open, instead, when opened slightly raise the door off the unit.
- Lay the door on the floor.
- There are three sheetmetal screws on each side of the door, using your nut driver remove these screws. They secure outside of the door to the inner door.
- Stand the door up on the floor and raise the outer door panel, there are several plastic clips on each side the slide into slots on the inner door panel. I found it a little difficult to separate the panels, but with gentle persuasion they came apart.
- Lay the inner panel on the floor with the exposed electrical components facing up.
- At the top of the inner panel is a black plastic cover protecting the electronic components, this where the control panel lives.
- Remove the sheetmetal screws that secures this plastic cover.
- There are two wiring harnesses, remove them.
- The defective component can be lifted out.
- Install the new control panel.
- Reassemble.

I had to replace a docking port. Parts Select had the part, labeled as stainless, just as this survey indicates. Well folks, the part I received is 100% plastic. It it the correct part, just not stainless. Should it have been stainless due to a faulty plastic design? I don’t know.

I used Parts Select for the simple directi ... Read more ons for installation. I was eventually linked to a YouTube video for a completely different docking port. Does my part slip on? Does it press in? I don’t know.

Needless to say, this has been a cheap but frustrating ordeal that is not yet over. Thanks for having the stainless, but really plastic, part and for having directions for some other part available.

Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!

Followed instructions used flat head screwdriver to unlach old arm. Took out and put in new spray arm. Really easy

First, drain as much water as possible using a shop vac or siphon. Unscrew two plastic lugs and food screen to release the metal *disk* found inside the dishwasher at the bottom. Then, remove the grey retainer ring found under the food screen.
Using the nut driver, remove two screws from the white plastic retainer ring at bottom th ... Read more e flood switch.
I used pliers to grip the ring to take it out.
**Dry everything in the "well" where the flood switch sits.**
Now, remove the bottom front cosmetic panel. This exposes the underside of the appliance. Locate the flood switch wire underneath and gently pull down the small black plastic tab which holds the wires in place. This allows more movement to make your job a little easier!
Pull up on the flood switch and simply unplug it and swap in your new switch! Replace everything as you found it, don't over-tighten your screws, and make your kids load that sucker! Hope this helps, and have a beautiful day!

the part is OEM and fits like a glove. No worries. There is a minor variation in design and is not like for like design but fits exactly per specs and works. I have been looking for this part for years now. Thank you for PS for maintaining the inventory.
PS12743260Manufacturer Part Number WD28X26099

After replacing UI board, I replaced the mainboard. still did not solve the problem. The element tested good and I had removed the flood switch, rinsed and blew it out so it rattled but the damage was done. Replacing it made the dishwasher heat water and heated during dry cycle. Removed fine filter, removed course filter, removed two ... Read more screws with nut driver, removed flood sensor and then reversed. A year or so ago, the dishwasher flooded for no apparent reason, wondering if that was the beginning end of the switch!

The part is held in with two plastic clips, which are easy to unclip. The part needed to be slightly flexed to release it and the new part went in the same way the old one came off. One issue: The replacement part had one extra row of tines that encroached on the silverware basket. As it turned out, one tine fit between basket sections ... Read more and the other fit through the hole in the bottom of the basket and it doesn't interfere with utensils so it turned out not to be a problem.

Installed new heater by pulling unit out of it’s cubby hole. Was able to gain access to the nuts that hold it down and make the seal, as well as the electrical connections. Re-installed. Helpful if you remove both dish baskets and utencil basket for access when installing heater.

Parts diagram shows Striker can be popped out with screwdriver. Not true. It has a screw bolting it internally. Impossible to get to unless you disassemble the entire door. We took a power drill and small drill bit and bore it out like a cavity in a tooth. Needle nose pliers to extract the screw. Pretend your a dentist. Fixed it in 5 ... Read more minutes. Replacement fit tight. A+

I simply followed the video instructions and replaced the rack myself, no tools required. Easy peasy

Just snapped it in place and that’s it!

Took out the old heating assembly and installed the new one
this did not solve my problem and I ended up buying a new dishwasher and returned the part
Spent as much in shipping to get the part and return it as the part cost itself
Next time I will just replace the dishwasher in the first place.

Performed all checks on youtube...water coming in, course and fine filter cleaned, drain pump working (heard it come on and no water present and cycle end). Swapped water inlet valve bc it was the cheapest poss fix $19. No luck. Ordered circulation pump and motherboard. Swapped pump, very easy with machine out and turned on its back. Temp ... Read more reinstall and ops checked good. Contacted Partselect for return slip, emailed immediately and sent thru post office.