EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

DDT575SSF0SS General Electric Dishwasher - Instructions

All Instructions for the DDT575SSF0SS
31 - 45 of 131

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Prongs of upper & lower trays were breaking off.
6 of 6 people found this instruction helpful.
  • Fean from VENICE, FL
  • Really Easy
  • 15 - 30 mins
The lower tray was simple. Lifted the old one out and placed the new one on the lid of dishwasher.

Upper tray: Used the closed point of scissors to gently push the little piece of plastic on the slide and removed the cap on each slider. Pulled the damaged tray off of the sliders. Removed the piece that shoots the water ont o the dishes and placed it on the new tray. Put the tray back on the sliders and replaced the little caps back onto the slider so that the tray did not come off of the track. Voila!!
Was this helpful?
Thank you for voting!
Thumping Sound during the WashRinse cycles
6 of 6 people found this instruction helpful.
  • Jedrino from HAWTHORNE, CA
  • Very Easy
  • Less than 15 mins
Chances are your Lower spray arm is worn or jets are off. Replacing this part is very easy. Grab the base of the lower spray arm, twist and pull straight up. Place the new one in and twist lock in place. Repair complete!
Was this helpful?
Thank you for voting!
Dishwasher would not receive water when started
6 of 7 people found this instruction helpful.
  • Jason from WESTON, WV
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
The service lady looked up possible trouble items and narrowed it down to the flood switch. Being the most likely cause, I ordered a new one. I removed both trays, the lower sprayer, and both screens. The flood switch has an electric plug on the bottom of it that just pulls off. Just as with other appliance repairs, I actually got the ol d flood switch to work again before trying the new one. I should have tried to free up the float before ordering the new one. But in case this happens again, I’ll just put the new one in.
Was this helpful?
Thank you for voting!
Dishwasher won't start.
7 of 10 people found this instruction helpful.
  • John from CROSSVILLE, TN
  • Very Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!
Was this helpful?
Thank you for voting!
Dishwasher not heat or drying dishes
5 of 5 people found this instruction helpful.
  • Mike from FRESNO, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
Turned off pier at breaker. Removed dishwasher from under counter after disconnecting water line from dishwasher and drain tube from under sink. You might get a little residual water but not much. Removed old flood switch took about 2 minutes. Replaced with new flood switch. Then tilted dishwasher back to get to plastic nuts that hold dow n heating element. Set unit back down and removed old heating element then replace it with new one. Replace plastic nuts that hold element. Exact parts makes job easy. Them put water hose back on an put washer back in place hooked drain hose back up. Turned water and power back on. Tested unit worked perfectly. Hardest part of job was putting the dishwasher back into counter and getting the Instalation back on top.
Parts replacement time was about 10 minutes.
Disconnecting and reconnecting and replacing dishwasher 40 minutes. But I wouldn’t pay anyone to do this because it’s really not difficult.
Was this helpful?
Thank you for voting!
Leak at bottom of door
5 of 5 people found this instruction helpful.
  • FREDERICK from FORT MYERS, FL
  • Really Easy
  • 30 - 60 mins
I did not do repair. I originally tried to order part from GE. They informed me I had to buy the whole door to replace the bottom door seal. I then looked at Part Select and they had the exact schematic as GE except showed the seal. I called and sales person assured me it was the part I was looking for. My dishwasher. What they didn’t te ll me was that seal is riveted to the door. I ended up throwing away the part as it was more expensive to return it . SonPart was a total waste..
Was this helpful?
Thank you for voting!
Upper Spray Arm broke in half from hitting something in the upper rack.
5 of 5 people found this instruction helpful.
  • Howard from PORT TOWNSEND, WA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Had to remove the rubber gasket on the new spray arm to install the device, as it was hard to push into the above slot that fits the arm..
Was this helpful?
Thank you for voting!
Lower arm spray had hole melted in it
5 of 5 people found this instruction helpful.
  • Joe from Rio Verde, AZ
  • Very Easy
  • Less than 15 mins
Simply put it on and twist it to lock in place. Took all of 3 seconds
Was this helpful?
Thank you for voting!
Lower dish rack assembly plastic had melted through to the metal
5 of 5 people found this instruction helpful.
  • Susan from ATASCADERO, CA
  • Really Easy
  • Less than 15 mins
Simple! I removed the flatware tray and pulled out the old rack assembly. Rolled in the new one and replaced the tray. Not really a "repair" per se but a needed replacement.
Was this helpful?
Thank you for voting!
racks were worn out
5 of 5 people found this instruction helpful.
  • Bruce from POMPTON LAKES, NJ
  • Really Easy
  • Less than 15 mins
took out old and replaced with new
Was this helpful?
Thank you for voting!
Water leak corners of door onto the floor
5 of 5 people found this instruction helpful.
  • John from Aston, PA
  • Really Easy
  • Less than 15 mins
After hours looking for problem. I tried cleaning door gasket. Did not stop leak. Looked at lower water spray arm and it was split. It is literally a 2 minute repair to remove and install. Knock on wood, no leaks in the last 10 washes.
Was this helpful?
Thank you for voting!
Dishwasher would not start Would run if you added 2 qt. water manually
5 of 5 people found this instruction helpful.
  • Mark from FAIRFAX, VA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Unplugged power.
Shut off water supply.
Remove the kick panel.
Unscrewed dishwasher from under cabinet and side screws. lower feet to reduce tension.
As you slide the dishwasher out, be sure all lines (Drain, water supply, electric are free to move with dishwasher.
I was able to hold the dishwasher at an angle to easily get to the valve. After removing the the valve, i screwed the new valve back into place. I removed the Line between the valve and Dishwasher. Putting the line on the new valve. I removed the water supply line from the old valve and installed it on the new valve.
Placed the dishwater back in place and screed it back in. I ran the cycles. everything works!
I replace the kickpaner a couple of hours later. Check to make sure there were now leaks.
Was this helpful?
Thank you for voting!
Dishwasher wasn't heating water
5 of 5 people found this instruction helpful.
  • Daniel from CONCORD, NC
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
So after noticing some horrid food waste build up in my 9 year old dishwasher, I determined it wasn't heating the water during the wash cycle. I came on here to check how to replace the heating element and was surprised when the flood switch was instead strongly recommended as the first repair step.

I ordered the part, and prep ped the dishwasher for the repair (Pro-tip: Clothes pin attached to the bottom of the flood switch wiring harness ensures it doesn't slip down below the opening during the part swap!). The part swap and reassembly only took 5-10 mins or so after prep and dishwasher is now heating water and running great again. Many thanks to partselect.com for the detailed installation guides/videos and the parts recommendations!
Was this helpful?
Thank you for voting!
I had a hole in the drain line of my dishwasher.
5 of 5 people found this instruction helpful.
  • Tina from SOUTH WEST CY, MO
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
It was relatively easy to fix. I unscrewed the mounting screws from the cabinet, slide the dishwasher out to access the pump under the dishwasher, I did raise the dishwasher on the left side and steadied with a stool to make access to the pump fitting easier. Then I loosed both clamps at the ends of the hose ie. from the dishwasher pum p and the connection to the sink drain line, pulled the clamp off of the end that connects to the pump and placed it on the new hose connection, I removed the old hose, connected the new one and tightened the drain line connections. I placed the hose in the hose holders on the side of the dishwasher slid the dishwasher back into place and secured it in place with the mounting screws.
Was this helpful?
Thank you for voting!
3 Plastic rollers on bottom of dish basket came off and melted by the heating coil in dishwasher,
5 of 6 people found this instruction helpful.
  • BENJAMIN from ONALASKA, TX
  • Very Easy
  • Less than 15 mins
Simply pick the basket up to slide wheels onto axles and push in until they lock in place.
Was this helpful?
Thank you for voting!
All Instructions for the DDT575SSF0SS
31 - 45 of 131