EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

CW20P8WC Crosley Washer - Instructions

All Instructions for the CW20P8WC
61 - 75 of 350

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Random slow spin during Rinse cycle and would then shut off and not drain
2 of 2 people found this instruction helpful.
  • Frank from BRADFORD, MA
  • Easy
  • 30 - 60 mins
  • Screw drivers
Top loader May Tag washer with open bottom. After research I presumed it needed a new belt, or Transmission, which runs 3 pulleys under the open bottom. After tipping the washer back for inspection, saw oil splatter underneath. Removed old belt by turning largest pulley on Transmission while pulling the belt "off" the edge. Belt was aged, Stretched and worn. Belt and all 3 pulleys were oily causing slippage. The main large Drive pulley on the Transmission shaft, has a plastic snap on grease cup at it's center. I snapped it off with screw driver. The cup was partially full of thinned old grease causing the oily mess. There's a C clip inserted in a groove on the end of the drive shaft holding the pulley on. Removed the C clip with screw driver tip and slid off the Drive pulley. The Center of the pulley contains a plastic ratchet assembly that operates the washer tub cycle to rotate and stop and repeat. The ratchet assembly falls right out, and in the end of transmission is a Thrust washer which can be pulled of easily also. I Cleaned all 3 pulleys with De-greaser and finally with Rubbing Alcohol to dry the pulley surfaces. Then cleaned and removed all grease from the plastic ratchet assembly parts and cleaned them. Then I Repacked everything including the Drive shaft with "heavier" Grease that would not break down so easy. Reassembled everything in reverse and installed on the shaft. Snapped the C clip back on to hold pulley back in place and then the Grease cup, which just snaps back in place with a push. Installed new drive belt in the same manner it was removed, only in reverse by turning the pulley, and pushing the belt "on" over the edge of the pulley. Problem fixed and washer works perfect again with Noticeably better operation through all washer cycles.
Was this helpful?
Thank you for voting!
My washing machine would be extremley loud when washing clothes then one day it stopped working.
2 of 2 people found this instruction helpful.
  • damian from carpentersville, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers
First i unscrewed the bottom latch to check inside the maching, i then disconected the vertical style pump with pulley from its position and i discoverd a huge crack that was made by a loose pulley. After that i ordered another pulley from this web site easaly installed the pulley and now my maching works like new. The part was less than 50 bucks i saved over 200 bucks by not going out and buying a new machine.
Was this helpful?
Thank you for voting!
Noise from pump
3 of 5 people found this instruction helpful.
  • Donald from Brielle, NJ
  • Really Easy
  • 15 - 30 mins
  • Socket set
On a scale of 1 to 5 (with 5 being the most difficult), I would rate this a 2 or 3. It is just a matter of knowing how to access the pump. First I unplugged the washer. Then used putty knife to push in clips to lift up top of washer (the clips are located about 1 inch in from each side). Used socket to remove the two screws holding on front panel. Disconnected the two hoses from pump using pliers to squeeze clips (be sure to have cup or bowl handy because water will come out of the hoses). Lifted up washer and removed belt from pump. Used socket wrench to remove pump and replace with new one. Reattached hoses and belt. Reattached front panel and closed the top of the washer. Everything was easy to access.
Was this helpful?
Thank you for voting!
Left hinge pin & hinge sheared
2 of 2 people found this instruction helpful.
  • Tom from Camp Verde, AZ
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Hving read some of the tips in regards to this repair I set out with equal parts of confidence & apprehension. The advice of shifting the tub toward the hinge to be removed is in itself the key to the whole procedure. After having done so & wedging a dust pan handle between the tub & frame to first one side & then the other, I removed the entire lid with the hinge & hinge pin assys. attached as ther is not sufficient clearance to slide a servicable hinge pin from a hinge when only one hinge has beeen removed. With the lid completely removed access to the hinge pin(s) is straight forward. I suggest screwing & unscrewing the fastening screw into a new hinge assy before mounting the hinge onto the machine & also using an offset philips screwdriver or ,as I did, a 1/4" drv. ratchet with a #2 philips apex bit which allows for a better feel & more control over the upside down blind operation of removing & replacing the fastening screw into the hinge assy. Hope this helps. Tom
Was this helpful?
Thank you for voting!
Makes squeaky noise when stop spinning
2 of 2 people found this instruction helpful.
  • Hing from Toms River, NJ
  • Really Easy
  • Less than 15 mins
I checked the belt 1st. It didn't look like it could be the problem, but it needs replacement anyway. Replacing belt is very easy, this 1 is at the bottom of the washer.

1. Unplug washer.
2. Move it away from the wall.
3. Tilt washer back & support the bottom front with lumber.
4. You can see the belt looped a round 3 pulleys. Water pump in the back. The motor is in the right front & is spring loaded.
5. Grab the motor pulley & push it back as far as it will go, & remove the belt from it.
6. Do the reverse to install new belt.

There is a Brake Rotor & Lining Assy on this washer. I looked up the part on this web site, sure enough somebody else had this same problem. Part is on order. If this is not the fix, I will revise this posting later.
Was this helpful?
Thank you for voting!
actuater broke and I replaced it in 5 minutes
6 of 14 people found this instruction helpful.
  • Thomas from Clayton, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
unscrewed screw holding old actuater in and replaced it whith the new part.
Was this helpful?
Thank you for voting!
Wind blew lid off washing machine while being moved
2 of 2 people found this instruction helpful.
  • Lisa from West Branch, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I lifted the top of the washer to get access to the screws that held the hinges in place, unscrewed them, removed the broken hinges and put the new ones on, replaced the screws and closed the top. It was very easy. I was amazed that I could still get replacement parts and at such a great price, less than $15.00 with shipping!
Was this helpful?
Thank you for voting!
Would not go into spin cycle to empty water from tub.
2 of 2 people found this instruction helpful.
  • Clarence from Belton, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
I unpluged the washer from the 120VAC supply, then moved it away from the wall about a foot. I removed the knobs from the washer front control panel. I removed the control panel screws (4) and exposed the timer. I used a nut driver to remove the timer, and unpluged the wiring harness. Replaced the wiring harness, remounted the new tim er, and put everything back together. The washer works great. I had replaced the same timer about 10 years ago.
Was this helpful?
Thank you for voting!
Lid hinge broken
2 of 2 people found this instruction helpful.
  • Elwyn from Kansas City, MO
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The hardest part was finding the model # on the back. I couldn't move the washer out...so used a mirror! I used a putty knife to pop the 2 fasteners securing the top. Tilted it up & proped with a plastic clothes hanger. Unscrewed the one screw which is easy to get to with the top up. Replaced the hinge with the 1 screw. Closed the t op. Gave the broken hinge to my wife as an early Mother's Day present.
Was this helpful?
Thank you for voting!
rinse cycle was not expelling the water
2 of 3 people found this instruction helpful.
  • bert from coudersport, PA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers
remmoved the screws on the back that hold the panel on. removed the two hoses attched to the pump. removed three screws and pulled the pump out. spun the pulley and noticed no movement inside. looked closer at the pulley to notice it was broken. ordered new pulley online. received quickly. new part fit exacttly right. put three sc rews back in. hooked two hoses back up. put belt on pulley. plugged in and worked great.
Was this helpful?
Thank you for voting!
Pump needed replacing
2 of 3 people found this instruction helpful.
  • Thomas from Los Alamos, NM
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Removed the front panel to get some light in to the machine. Removed the two hoses connecting the pump to the drain and tub. Removed the three screws holding the old pump in place. Did the reverse to install.
This was a piece of cake.
Thanks for having the parts needed to do this job.
Tom
Was this helpful?
Thank you for voting!
Pump was frozen
2 of 3 people found this instruction helpful.
  • Frank from Sugar Land, TX
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Socket set, Wrench set
Replacing the pump with the new pump was very easy for me, because of my degree in Mechanical engineering, so I am use to dealing with pumps, engines, gears,etc. However, my wife watched me do the entire job and she is now able to replace this part in the future. The design of the Maytag is very simple to repair, and for that I am very g reatful that we can order the parts and do the repairs ourselves withhout having to call a repairman. This was our first problem after 6 years of smooth operations by this washer.
Was this helpful?
Thank you for voting!
Washing machine was noisy (metal on metal) after the tub filled up and the motor engaged for the wash cycle.
2 of 3 people found this instruction helpful.
  • GARY from Montvale, NJ
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
I unplugged the machine, tipped it back slightly and rested in on a gallon paint can. I inspected the under side and manually advanced the fan belt to hear if I could hear the noise at the water pump. The pump pulley and shaft was worn and there were metal shavins (small) on surface of pulley.

Then I removed the belt from the p ulley, rested the machine back to normal position, removed front panel (two sheet metal screws on inside top), removed the water pump hoses (htere is water int he hose & pump assembly so you will get some water on floor.

Then I removed the pump and ordered a new one. The installation was the reverse, machine works like new and the washer tub spins better than ever during the final rinse and spin, since the worn water pump was binding and stressing the machine.

Thanks to Part Select - Your website is awesome and your service instructions and user advice gave me the confidence to do the repair myself. I saved $150 - $250 for the repair.
Was this helpful?
Thank you for voting!
Noisy on spin cycle
2 of 3 people found this instruction helpful.
  • William B from STURGIS, MI
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Followed the excellent utube instructions you provide. Piece of cake when I followed the video. The rear springs became much more difficult because my model does not have rear access panel. They were the only stuggle. Thank you for doing the repair videos
Was this helpful?
Thank you for voting!
No belt and no motor gear
2 of 3 people found this instruction helpful.
  • Matt from Hoboken, NJ
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers, Wrench set
Pop the top of the washer and use the nutdriver to remove the two screws holding the frontpanel on. Use the nutdriver for two more screws holding the plastic motor cover on. Use nutdriver for the two BIG screws holding the motorplate to the washer frame. After this, I literally beat/chiped/sawed the old motor geat off. Once that was d one, I put the new one on; had to use a hammer to knock it all the way on (try not to damage the clips). Reassemble everything. Flip washer over and place bet around two smaller gears. Rotate main tub gear to feed belt on. Make sure you use the nutdriver to loosen/tighten the motor positioner screws in the slots if things aren't working here.
The only really hard thing was taking the old motor gear off.
Was this helpful?
Thank you for voting!
All Instructions for the CW20P8WC
61 - 75 of 350