EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

CW20P8WC Crosley Washer - Instructions

All Instructions for the CW20P8WC
46 - 60 of 350

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water pump failure
5 of 6 people found this instruction helpful.
  • John from Alhambra, CA
  • Easy
  • Less than 15 mins
  • Nutdriver, Pliers
Disconnect electricity....remove front panel by gently prying up lid.... Remove two small screws at corners of front panel. You may need small nutdriver here or very small hands, you can easily swivel tub out of the way....once front panel is off water pump is at the bottom right... It is only connected by two squeeze clamps and 3 nuts... This is obviously where the adjustable wrench and nutdriver come in very handy... Otherwise this job will be a bit longer....be prepared for residual water to pour out...you will need towels or a bucket....replace old with new one by reversing the process...at this point tilt the entire washer on it's backside or at least at a 45 degree angle to access the bottom... Swivel the motor away to slack up the belt...remove belt and replace in reverse order of diassembling.... Should take no more than 15 minutes.... Good luck!!!!!
Was this helpful?
Thank you for voting!
lid switch acuator broke and some cycles would not work
5 of 6 people found this instruction helpful.
  • Brian from Woodbury, MN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
unscrew the screw holding the broken part in the lid to remove the old part and tighten the screw to a firm position to hold the new piece in place. Now working fine.
Was this helpful?
Thank you for voting!
washer overflowing
7 of 12 people found this instruction helpful.
  • Aaron from Lawton, OK
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Once the washer was unplugged, i removed the two screws on the back pannel, disconnected the three wires, rubber water line, and two screws holding it to the control panel. Quite simply reversed the process with the replacement part i ordered, which arrived overnight, and the problem was solved.
Was this helpful?
Thank you for voting!
Washer was making noise during spin cycle
4 of 4 people found this instruction helpful.
  • William from MORGANVILLE, NJ
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
Hardest part was finding part that needed the needed repair. Searching the web for issues associated with the sound resulted in many links. Once the sound was found, I went to the video to see how to remove the Water Pump so I could examine it to confirm that was the correct piece. It took about 15 minutes to remove the part. Since I h ad to remove the belt to get it out, I realize that the belt needed replacement as well. So both parts were ordered. Replacing the parts also took about 15 minutes. Relatively easy repair. Be aware that the video on the part select video shows the water pump in a different location than the Maytag washer. To get to the Maytaq water pump, there is a panel in the back that had to be opened to access the water pump.
Was this helpful?
Thank you for voting!
washer lid was no longer connected
3 of 3 people found this instruction helpful.
  • linda from granada hills, CA
  • Easy
  • Less than 15 mins
Pulled up the top of the washer and removed the lid hinge with a star tip screw driver. Realized that I also needed the hinge pins and had to reorder those. They should come as a kit.
Was this helpful?
Thank you for voting!
My Washer's lid hinges broke while it was being moved.
3 of 3 people found this instruction helpful.
  • Gary from Mesa, AZ
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I obtained the parts on line and began to install these. I was surprised that the ease of my installation was great. Each part was held by one screw. I used a phillips driver and found the under screws easy to get to by pushing the inside clothes drum to the side. A total of four screws was required for the replacement. This repair w as so easy that a normal non-trained person can accomplish it. Thanks Admiral.
Was this helpful?
Thank you for voting!
Washer was making a squeak during spin cycle & then just stopped spinning
3 of 3 people found this instruction helpful.
  • Eleanor from PALATKA, FL
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
I watched the video of the repair on this website and followed it. Was really easy & THANK GOD because this was my first repair. This has been a great machine and it looks like it will continue to be for a little while longer! Thanks for the video help and friendly navigation of your site!
Was this helpful?
Thank you for voting!
Washer always going off balance full loads or small
3 of 3 people found this instruction helpful.
  • Jeffrey from HONEY BROOK, PA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Socket set, Wrench (Adjustable)
I tilted top cover to remove front washer panel removed suspension springs to remove complete tub assembly to gain access to bottom. Drive pulley to remove snubber ring I performed the repair step by step as per your video. was dead on made the repair go smoothly. I installed the belt last tilting washer mechine back to gain access to und ercarrige just walked belt on all three pulleys self adjusting then. made sure washer was level. Front to back side to side no rocking in any deriction My wife did four full loads problems gone I think all needed to be done to complete repair snubber ring , washer drive belt, & leveling machine all played there roll in putting washer back in factory working condition washer not a angery walking vibration nightmare
Was this helpful?
Thank you for voting!
Our washer was purchased 1/6/2006 and it started banging and walking out of its place when the washer started into the spin cycle. This would occur no matter the size of the load.
3 of 3 people found this instruction helpful.
  • Pamelia from LA CROSSE, VA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
We followed the instructions show on the video. However, our model was assembled slightly different. We had to remove the screws from both sides of the side panels so that we could remove the tub from inside of the machine. Also our model only has one belt not two.
Over all it was easy considering my husband and I had never attempte d to repair a washer. Once we got it back together it when back to working like it had never been broken!
We would have never been able to repair our washer without the video that your site provided... thanks so much!!??

Sure wish the manufactures would consider making the older models again as lots of us are not happy with the new modules being manufactured presently!
Was this helpful?
Thank you for voting!
White fluffy residue appeared under washer. Unbalanced banging during spin cycle
4 of 6 people found this instruction helpful.
  • John from Blue Bell, PA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Parts needed: Snubber Ring and 6 Springs (don't put the old springs back)
Unlug the AC cord, open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back It was not necessary to rem ove the back cover. Remove the little hose going to the basket from the control module. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING: DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK. Seriously! Install the new ring, center and tighten the screws. Put the tub back in. I found it handy to support the tub with a 2x3 to get the springs back in. Connect hoses back up. It really isn’t that bad, a couple of scraped knuckles.
Was this helpful?
Thank you for voting!
lid hinge broken
3 of 3 people found this instruction helpful.
  • VALERIE from PARKER, CO
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I'm a 69 year old female. My husband isn't very handy so I decided to order the parts and do it myself. I didn't know how to take the machine apart so I just moved the washer part so I could unscrew the screw. I dropped the screwdriver between the adj. and side of the washer. I guess you won't be telling this story. I did get the parts on and the lid is working and so is the machine. Valerie Guyot
Was this helpful?
Thank you for voting!
Leaking water inlet hoses.
4 of 6 people found this instruction helpful.
  • Helen from NASHUA, NH
  • Really Easy
  • 30 - 60 mins
Removed the old hoses and screwed on the new hoses.
Was this helpful?
Thank you for voting!
Washer Traveled and load would not be balanced. Washer would bang loudly.
4 of 7 people found this instruction helpful.
  • James from ELMORE, OH
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Followed directions from video on your site. It was very helpful. The snubber ring fixed the problem.
Was this helpful?
Thank you for voting!
Top cabinet was rusted on one corner due to liquids dripping from a shelf
3 of 4 people found this instruction helpful.
  • John from Spring Valley, CA
  • A Bit Difficult
  • More than 2 hours
  • Screw drivers, Socket set
1. Disconnected the electrical cord from the socket & the hose lines from the faucets.
2. Pulled out the washing machine from against the wall to make room for working.
3. Opened the back of the control cabinet by removing the 5 screws.
4. Disconnected the wiring ( making sure to identify all connections and color of wiring ) from the control cabinet and pulled through the opening on the cabinet top.
5. Popped the lid open from the front of the washer using a screwdriver by prying it open and removed the hinge lid from the cabinet top.
6. Removed the control cabinet from the cabinet top, disconnected the safety latch from the cabinet top.
7. Removed the water inlet guide & a vacuum hose from the cabinet top.
8. Removed the hinge brackets from the back of the washer which holds the cabinet top in place.
9. Removed the hinged lid from the cabinet top..
10. Installed new hinges on to hinge lid .

Installed new cabinet top in reverse order as above.
Was this helpful?
Thank you for voting!
Unit quit spinning
2 of 2 people found this instruction helpful.
  • Leo Joseph from BENSON, NC
  • A Bit Difficult
  • More than 2 hours
  • Pliers, Screw drivers, Socket set, Wrench set
Actually I got on YouTube and looked up the problem and watch the short video of it and went from there and it showed me how to take everything apart what the problems were and as I did take it apart and found out it was exactly what they said I simply reversed it just ordered the parts and put them in and took my time to make sure that e verything was to specs as I've measured the clearance of the break and said all the hardware back in place it was quite simple yet it was just time consuming took me about two and a half hours but it runs quiet spins great just like a brand new one I couldn't be more pleased with it and I saved quite a bit of money doing it myself
Was this helpful?
Thank you for voting!
All Instructions for the CW20P8WC
46 - 60 of 350