CW20P8HSC Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The water was leaking out from the bottom.
1 person
found this instruction helpful.
-
Doris from Plainsboro, NJ
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
My husband took out the 2 screws in the front panel and loosen the 3 nuts from the pump.
The parts was easily removed and the entire job tooked 30 mins.
The parts was easily removed and the entire job tooked 30 mins.
Was this helpful?
Thank you for voting!
Washer had bad water pump
1 person
found this instruction helpful.
-
Edwin from Eagar,, AZ
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Removed access panel to expose pump, removed drive belt, and old pump, repeated the avove steps in reverse order, tested for leaks and proper operation.
Was this helpful?
Thank you for voting!
washing machine squeaked on the spin cycle
1 person
found this instruction helpful.
-
Jeffrey from Wabash, IN
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
removed hoses and belt. removed 3 screws that secured pump. and then removed pump. received new pump and just reversed the process to repair!
Was this helpful?
Thank you for voting!
The water pump went out
1 person
found this instruction helpful.
-
felicia from Broken Arrow, OK
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
UNPLUG ELECTRICITY. I pulled out the washing machine turned the water off pulled all of your hoses from the back of the machine there may be a mess so you need some thing that will catch the water as it comes out of the hoses. On the bottom of the machine is a belt you have to remove it. Its easy just pull it off. On the back is a panel t
... Read more
hat you unscrew four screws. On the water pump it self you unscrew three screws. Then for the new part you do in reverse order screw your three screws back in put your hoses back on make sure your clamps are tight around your hoses or you will have a leak. Put your panel back on. Put your belt back on. Turn your water on from the wall plug in the electricity and you are done.
Read less
Was this helpful?
Thank you for voting!
Problem manifested as a loud squealing/grinding noise during all cycles.
1 person
found this instruction helpful.
-
Michael from Atlanta, GA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Disconnected both power and hot and cold input water lines. Laid the washer on its front side for access to the bottom. Removed the small access panel from the back of the machine to remove the metal screws holding the pump in place. Removed the single drive belt. New pump installed easily, replaced the belt and access panel. Reconne
... Read more
cted the power and water hoses and everything worked fine.
Read less
Was this helpful?
Thank you for voting!
Water removal pump stopped working.
1 person
found this instruction helpful.
-
Timothy from Palmdale, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Removed lower rear panel by removing 8 screws. Then I removed the two hoses that are attached to the pump by removing the hose clamps with a pair of plyers. The three hex head screws that anchor the pump to the base of the washer unit were removed and the pump came right out. To put the new pump in I just slipped the pump through the hol
... Read more
e at the bottom of the washer and attached the belt onto the pulley. Then reversed the installation process. The washer had to be tipped forward slightly for this process and blocked (approx. 8 in.) to allow access to pulley. Very easy install, no help needed. Washer must be empty and preferable dry when task is done or water will be everywhere.
Read less
Was this helpful?
Thank you for voting!
Drain pump making load screeching noise
1 person
found this instruction helpful.
-
Danny from Fort Worth, TX
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
I pulled washer out and removed filler hoses from water supply and drain hose and tilted it forward placing three short 2X4's under the washer to keep it tilted forward. Removed
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nut ... Read more driver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nut ... Read more driver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.
Read less
Was this helpful?
Thank you for voting!
it was spinning slowly or not at all
1 person
found this instruction helpful.
-
Louis from FREMONT, NE
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I first changed the belt which helped but it still sounded like it was going to take off through the roof.....I did the pulley and bearing kit in hopes that it would do some good....it went really smoothly with no issues however it did not solve the problem....so it is working and I am going to just ride it out until it quits....thanks
Was this helpful?
Thank you for voting!
Water leaked from bottom of Washing Machine.
1 person
found this instruction helpful.
-
Brandon from Lake Elsinore, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
Removed water lines and drain, removed back panel, removed drain lines from pump. Unscrewed 3 screws to remove pump. attached drain lines to new pump, screwed in new pump, reattached everything. Reinstalled belt (very easy, not like an altenator). done
Was this helpful?
Thank you for voting!
water not draining
1 of 2 people
found this instruction helpful.
-
FRANK from CHULA VISTA, CA
- Really Easy
- 15 - 30 mins
-
Socket set
changed drive belt and saved me from buying new washer,,working like bland new again ...many thanks
Was this helpful?
Thank you for voting!
Made noise during washing and rinse cycle
1 of 2 people
found this instruction helpful.
-
Jose from Elizabeth, NJ
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
It was easy to replace the water pump
Other Parts Used:
Was this helpful?
Thank you for voting!
Water pump replacement
1 of 2 people
found this instruction helpful.
-
Lon from Morton Grove, IL
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Socket set
Reverse the process to install new pump
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump
Reverse the process ... Read more to install a new pump
Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.
The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.
This was is 1st time we used your server but it won’t be the last!
Kudos to the entire staff and please…keep up the good work.
Sincerely,
Lon Thomas
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump
Reverse the process ... Read more to install a new pump
Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.
The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.
This was is 1st time we used your server but it won’t be the last!
Kudos to the entire staff and please…keep up the good work.
Sincerely,
Lon Thomas
Read less
Was this helpful?
Thank you for voting!
The Pump Went Out & Water Was All Over My Floor..
1 of 2 people
found this instruction helpful.
-
BILL from DIX, IL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Unscrewed the front panel. Then took pump out & put new one in. . . . . Thank you part select. Com. . . Super fast shipping. . .
Was this helpful?
Thank you for voting!
discharge pulley assembly bearing going out on it.
1 of 2 people
found this instruction helpful.
-
Milton from bartlett, IL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Went to website, looked up make and model, looked at photo's discription, studied it, and then went in and removed front panel, turned off water, removed clamps holding hoses too dishcharge pump, mopped up water, and then just reinstalled new piece, the way the old came out, re attached belt to pulley assembly, turned water back on, and d
... Read more
id a test for leakage and wala washer back in working order in less than an hour, and saved hundreds of dollars with out maytag repair man.
Read less
Was this helpful?
Thank you for voting!
Washing machine began making a screeching noise but only during the spin cycle - when it was emptying the water from the tub. After a few uses the machine just stopped working.
1 of 2 people
found this instruction helpful.
-
Patricia from Modesto, CA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
The pump was easy enough to replace. Access panel in the back and 3 screws and it was off and back on in less than 20 minutes. It was putting the belt on that gave me the most trouble even though one of the pulleys moved to allow for easy replacement it did not move enough. It took me another 30 minutes just to get the belt on. I fina
... Read more
lly decided to place the belt on the two smaller pulleys and save the larger one for last and it went on with no trouble at all. Learn from my error =]
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!