CW20P8HSC Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
My washing machine would be extremley loud when washing clothes then one day it stopped working.
2 of 2 people
found this instruction helpful.
-
damian from carpentersville, IL
- Easy
- 15 - 30 mins
-
Screw drivers
First i unscrewed the bottom latch to check inside the maching, i then disconected the vertical style pump with pulley from its position and i discoverd a huge crack that was made by a loose pulley. After that i ordered another pulley from this web site easaly installed the pulley and now my maching works like new. The part was less than
... Read more
50 bucks i saved over 200 bucks by not going out and buying a new machine.
Read less
Was this helpful?
Thank you for voting!
Noise from pump
3 of 5 people
found this instruction helpful.
-
Donald from Brielle, NJ
- Really Easy
- 15 - 30 mins
-
Socket set
On a scale of 1 to 5 (with 5 being the most difficult), I would rate this a 2 or 3. It is just a matter of knowing how to access the pump. First I unplugged the washer. Then used putty knife to push in clips to lift up top of washer (the clips are located about 1 inch in from each side). Used socket to remove the two screws holding on
... Read more
front panel. Disconnected the two hoses from pump using pliers to squeeze clips (be sure to have cup or bowl handy because water will come out of the hoses). Lifted up washer and removed belt from pump. Used socket wrench to remove pump and replace with new one. Reattached hoses and belt. Reattached front panel and closed the top of the washer. Everything was easy to access.
Read less
Was this helpful?
Thank you for voting!
Pump was frozen
2 of 3 people
found this instruction helpful.
-
Frank from Sugar Land, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Socket set, Wrench set
Replacing the pump with the new pump was very easy for me, because of my degree in Mechanical engineering, so I am use to dealing with pumps, engines, gears,etc. However, my wife watched me do the entire job and she is now able to replace this part in the future. The design of the Maytag is very simple to repair, and for that I am very g
... Read more
reatful that we can order the parts and do the repairs ourselves withhout having to call a repairman. This was our first problem after 6 years of smooth operations by this washer.
Read less
Was this helpful?
Thank you for voting!
Pump needed replacing
2 of 3 people
found this instruction helpful.
-
Thomas from Los Alamos, NM
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Removed the front panel to get some light in to the machine. Removed the two hoses connecting the pump to the drain and tub. Removed the three screws holding the old pump in place. Did the reverse to install.
This was a piece of cake.
Thanks for having the parts needed to do this job.
Tom
This was a piece of cake.
Thanks for having the parts needed to do this job.
Tom
Was this helpful?
Thank you for voting!
Washing machine was noisy (metal on metal) after the tub filled up and the motor engaged for the wash cycle.
2 of 3 people
found this instruction helpful.
-
GARY from Montvale, NJ
- Really Easy
- 30 - 60 mins
-
Nutdriver
I unplugged the machine, tipped it back slightly and rested in on a gallon paint can. I inspected the under side and manually advanced the fan belt to hear if I could hear the noise at the water pump. The pump pulley and shaft was worn and there were metal shavins (small) on surface of pulley.
Then I removed the belt from the p ... Read more ulley, rested the machine back to normal position, removed front panel (two sheet metal screws on inside top), removed the water pump hoses (htere is water int he hose & pump assembly so you will get some water on floor.
Then I removed the pump and ordered a new one. The installation was the reverse, machine works like new and the washer tub spins better than ever during the final rinse and spin, since the worn water pump was binding and stressing the machine.
Thanks to Part Select - Your website is awesome and your service instructions and user advice gave me the confidence to do the repair myself. I saved $150 - $250 for the repair.
Then I removed the belt from the p ... Read more ulley, rested the machine back to normal position, removed front panel (two sheet metal screws on inside top), removed the water pump hoses (htere is water int he hose & pump assembly so you will get some water on floor.
Then I removed the pump and ordered a new one. The installation was the reverse, machine works like new and the washer tub spins better than ever during the final rinse and spin, since the worn water pump was binding and stressing the machine.
Thanks to Part Select - Your website is awesome and your service instructions and user advice gave me the confidence to do the repair myself. I saved $150 - $250 for the repair.
Read less
Was this helpful?
Thank you for voting!
rinse cycle was not expelling the water
2 of 3 people
found this instruction helpful.
-
bert from coudersport, PA
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
remmoved the screws on the back that hold the panel on. removed the two hoses attched to the pump. removed three screws and pulled the pump out. spun the pulley and noticed no movement inside. looked closer at the pulley to notice it was broken. ordered new pulley online. received quickly. new part fit exacttly right. put three sc
... Read more
rews back in. hooked two hoses back up. put belt on pulley. plugged in and worked great.
Read less
Was this helpful?
Thank you for voting!
No belt and no motor gear
2 of 3 people
found this instruction helpful.
-
Matt from Hoboken, NJ
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers, Wrench set
Pop the top of the washer and use the nutdriver to remove the two screws holding the frontpanel on. Use the nutdriver for two more screws holding the plastic motor cover on. Use nutdriver for the two BIG screws holding the motorplate to the washer frame. After this, I literally beat/chiped/sawed the old motor geat off. Once that was d
... Read more
one, I put the new one on; had to use a hammer to knock it all the way on (try not to damage the clips). Reassemble everything. Flip washer over and place bet around two smaller gears. Rotate main tub gear to feed belt on. Make sure you use the nutdriver to loosen/tighten the motor positioner screws in the slots if things aren't working here.
The only really hard thing was taking the old motor gear off.
The only really hard thing was taking the old motor gear off.
Read less
Was this helpful?
Thank you for voting!
Noisy on spin cycle
2 of 3 people
found this instruction helpful.
-
William B from STURGIS, MI
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Followed the excellent utube instructions you provide. Piece of cake when I followed the video. The rear springs became much more difficult because my model does not have rear access panel. They were the only stuggle. Thank you for doing the repair videos
Other Parts Used:
Was this helpful?
Thank you for voting!
Water leak
2 of 4 people
found this instruction helpful.
-
Joe from Clearfield, PA
- Really Easy
- 15 - 30 mins
-
Socket set
Removed front cover, identified leak, ordered part, saved over half of the cost on part, no service call fee. I feel great!
Was this helpful?
Thank you for voting!
Wouldn't spin after rince
1 person
found this instruction helpful.
-
joe from LAWRENCEVILLE, NJ
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Followed the great instructions on your video
Was this helpful?
Thank you for voting!
Noise
1 person
found this instruction helpful.
-
Marylou from Old Forge, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Wrench (Adjustable)
I changed the piece easily
Was this helpful?
Thank you for voting!
Spin cycle out of Balance - Machine walks from wall
1 person
found this instruction helpful.
-
Needham from Leesville, SC
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Disconnect Power. Disconnect supply hoses. Open top by releasing top retainer clips with a thin blade or putty knife. Remove 2 sheet metal screws retaining front cover. Remove front cover. Lay a blanket on the floor and lay the machine over on its side leaving access to the front where the panel was just removed. Take belt off. Remove pu
... Read more
mp hose at bottom of drum. Prop up drum so it is centered in its normal position and not laying to one side. Do this near the lid end. Remove all centering springs - carefully. Drum and transmission assy will now come out through the front opening. Flip drum assy upside down with transmission up. Loosen the screws (do not remove completely - WARNING OF 200 LBS SPRING LOAD!) that clamp the snubber ring to the transmission. Remove the old snubber ring and replace with new. Be sure it is completely under the flange all the way around. Tighten the retaining ring screws. Reassemble all parts in reverse order. Done. Be sure to level the machine per owners manual instructions.
Read less
Was this helpful?
Thank you for voting!
Washer made horrible noise when entering the spin cycle.
1 person
found this instruction helpful.
-
Lance D. from Broken Arrow, OK
- Easy
- Less than 15 mins
-
Nutdriver, Pliers, Socket set
I removed the cover on the back of the machine, detatched the 2 hoses and removed the 3 screws holding in the Vertical Style Pump - with pulley. These screws are 10 mm nut-driver. The cover if I remember correctly was a standard rather than metric so make sure you have both available.
Screwed new part in, re-attached hoses an ... Read more d replaced cover. The last step requires strength to hold the machine up and re-configure the belt. This is best accomplished by looping it onto the tub and the pump first, the using the tub pulley to maneuver the belt onto the motor.
Only discouragement was that it took 8 days to receive the part as the first shipment was not the correct part at the fault of the distrutor.
Screwed new part in, re-attached hoses an ... Read more d replaced cover. The last step requires strength to hold the machine up and re-configure the belt. This is best accomplished by looping it onto the tub and the pump first, the using the tub pulley to maneuver the belt onto the motor.
Only discouragement was that it took 8 days to receive the part as the first shipment was not the correct part at the fault of the distrutor.
Read less
Was this helpful?
Thank you for voting!
pump bering failure
1 person
found this instruction helpful.
-
Robert from Englewood, FL
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
first i removed the front panel unclamped the hoses unscrewed the 3 screws that hold it in pulled it out, opened the new one and actually dropped it in and it fell into place with the holes lining up inserted the screws and hose clamps and reinstalled the belt which fell off when the old pump was removed, put the front back on and gave it
... Read more
a test then let the wife do a load of wash it worked like new
Read less
Was this helpful?
Thank you for voting!
water leaking from under front of washer
1 person
found this instruction helpful.
-
Mark from Isom, KY
- Really Easy
- Less than 15 mins
after doing some research I found out that a loose or slipping water pump belt could cause the water pump to not pump out the water correctly. Under the washer is the belt. All you do is have someone lift the front of the washer up enough that you can reach under and remove the belt. Then replace the belt back like you took it off.
Was this helpful?
Thank you for voting!