CW20P8ASC Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer always going off balance full loads or small
3 of 3 people
found this instruction helpful.
-
Jeffrey from HONEY BROOK, PA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Socket set, Wrench (Adjustable)
I tilted top cover to remove front washer panel removed suspension springs to remove complete tub assembly to gain access to bottom. Drive pulley to remove snubber ring I performed the repair step by step as per your video. was dead on made the repair go smoothly. I installed the belt last tilting washer mechine back to gain access to und
... Read more
ercarrige just walked belt on all three pulleys self adjusting then. made sure washer was level. Front to back side to side no rocking in any deriction My wife did four full loads problems gone I think all needed to be done to complete repair snubber ring , washer drive belt, & leveling machine all played there roll in putting washer back in factory working condition washer not a angery walking vibration nightmare
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer was making a squeak during spin cycle & then just stopped spinning
3 of 3 people
found this instruction helpful.
-
Eleanor from PALATKA, FL
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I watched the video of the repair on this website and followed it. Was really easy & THANK GOD because this was my first repair. This has been a great machine and it looks like it will continue to be for a little while longer! Thanks for the video help and friendly navigation of your site!
Was this helpful?
Thank you for voting!
Our washer was purchased 1/6/2006 and it started banging and walking out of its place when the washer started into the spin cycle. This would occur no matter the size of the load.
3 of 3 people
found this instruction helpful.
-
Pamelia from LA CROSSE, VA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
We followed the instructions show on the video. However, our model was assembled slightly different. We had to remove the screws from both sides of the side panels so that we could remove the tub from inside of the machine. Also our model only has one belt not two.
Over all it was easy considering my husband and I had never attempte ... Read more d to repair a washer. Once we got it back together it when back to working like it had never been broken!
We would have never been able to repair our washer without the video that your site provided... thanks so much!!??
Sure wish the manufactures would consider making the older models again as lots of us are not happy with the new modules being manufactured presently!
Over all it was easy considering my husband and I had never attempte ... Read more d to repair a washer. Once we got it back together it when back to working like it had never been broken!
We would have never been able to repair our washer without the video that your site provided... thanks so much!!??
Sure wish the manufactures would consider making the older models again as lots of us are not happy with the new modules being manufactured presently!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
White fluffy residue appeared under washer. Unbalanced banging during spin cycle
4 of 6 people
found this instruction helpful.
-
John from Blue Bell, PA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Parts needed: Snubber Ring and 6 Springs (don't put the old springs back)
Unlug the AC cord, open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back It was not necessary to rem ... Read more ove the back cover. Remove the little hose going to the basket from the control module. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING: DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK. Seriously! Install the new ring, center and tighten the screws. Put the tub back in. I found it handy to support the tub with a 2x3 to get the springs back in. Connect hoses back up. It really isn’t that bad, a couple of scraped knuckles.
Unlug the AC cord, open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back It was not necessary to rem ... Read more ove the back cover. Remove the little hose going to the basket from the control module. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING: DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK. Seriously! Install the new ring, center and tighten the screws. Put the tub back in. I found it handy to support the tub with a 2x3 to get the springs back in. Connect hoses back up. It really isn’t that bad, a couple of scraped knuckles.
Read less
Was this helpful?
Thank you for voting!
Leaking water inlet hoses.
4 of 6 people
found this instruction helpful.
-
Helen from NASHUA, NH
- Really Easy
- 30 - 60 mins
Removed the old hoses and screwed on the new hoses.
Was this helpful?
Thank you for voting!
Washer Traveled and load would not be balanced. Washer would bang loudly.
4 of 7 people
found this instruction helpful.
-
James from ELMORE, OH
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Followed directions from video on your site. It was very helpful. The snubber ring fixed the problem.
Other Parts Used:
Was this helpful?
Thank you for voting!
Random slow spin during Rinse cycle and would then shut off and not drain
2 of 2 people
found this instruction helpful.
-
Frank from BRADFORD, MA
- Easy
- 30 - 60 mins
-
Screw drivers
Top loader May Tag washer with open bottom. After research I presumed it needed a new belt, or Transmission, which runs 3 pulleys under the open bottom. After tipping the washer back for inspection, saw oil splatter underneath. Removed old belt by turning largest pulley on Transmission while pulling the belt "off" the edge. Belt was aged,
... Read more
Stretched and worn. Belt and all 3 pulleys were oily causing slippage. The main large Drive pulley on the Transmission shaft, has a plastic snap on grease cup at it's center. I snapped it off with screw driver. The cup was partially full of thinned old grease causing the oily mess. There's a C clip inserted in a groove on the end of the drive shaft holding the pulley on. Removed the C clip with screw driver tip and slid off the Drive pulley. The Center of the pulley contains a plastic ratchet assembly that operates the washer tub cycle to rotate and stop and repeat. The ratchet assembly falls right out, and in the end of transmission is a Thrust washer which can be pulled of easily also. I Cleaned all 3 pulleys with De-greaser and finally with Rubbing Alcohol to dry the pulley surfaces. Then cleaned and removed all grease from the plastic ratchet assembly parts and cleaned them. Then I Repacked everything including the Drive shaft with "heavier" Grease that would not break down so easy. Reassembled everything in reverse and installed on the shaft. Snapped the C clip back on to hold pulley back in place and then the Grease cup, which just snaps back in place with a push. Installed new drive belt in the same manner it was removed, only in reverse by turning the pulley, and pushing the belt "on" over the edge of the pulley. Problem fixed and washer works perfect again with Noticeably better operation through all washer cycles.
Read less
Was this helpful?
Thank you for voting!
Unit quit spinning
2 of 2 people
found this instruction helpful.
-
Leo Joseph from BENSON, NC
- A Bit Difficult
- More than 2 hours
-
Pliers, Screw drivers, Socket set, Wrench set
Actually I got on YouTube and looked up the problem and watch the short video of it and went from there and it showed me how to take everything apart what the problems were and as I did take it apart and found out it was exactly what they said I simply reversed it just ordered the parts and put them in and took my time to make sure that e
... Read more
verything was to specs as I've measured the clearance of the break and said all the hardware back in place it was quite simple yet it was just time consuming took me about two and a half hours but it runs quiet spins great just like a brand new one I couldn't be more pleased with it and I saved quite a bit of money doing it myself
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Makes squeaky noise when stop spinning
2 of 2 people
found this instruction helpful.
-
Hing from Toms River, NJ
- Really Easy
- Less than 15 mins
I checked the belt 1st. It didn't look like it could be the problem, but it needs replacement anyway. Replacing belt is very easy, this 1 is at the bottom of the washer.
1. Unplug washer.
2. Move it away from the wall.
3. Tilt washer back & support the bottom front with lumber.
4. You can see the belt looped a ... Read more round 3 pulleys. Water pump in the back. The motor is in the right front & is spring loaded.
5. Grab the motor pulley & push it back as far as it will go, & remove the belt from it.
6. Do the reverse to install new belt.
There is a Brake Rotor & Lining Assy on this washer. I looked up the part on this web site, sure enough somebody else had this same problem. Part is on order. If this is not the fix, I will revise this posting later.
1. Unplug washer.
2. Move it away from the wall.
3. Tilt washer back & support the bottom front with lumber.
4. You can see the belt looped a ... Read more round 3 pulleys. Water pump in the back. The motor is in the right front & is spring loaded.
5. Grab the motor pulley & push it back as far as it will go, & remove the belt from it.
6. Do the reverse to install new belt.
There is a Brake Rotor & Lining Assy on this washer. I looked up the part on this web site, sure enough somebody else had this same problem. Part is on order. If this is not the fix, I will revise this posting later.
Read less
Was this helpful?
Thank you for voting!
My washing machine would be extremley loud when washing clothes then one day it stopped working.
2 of 2 people
found this instruction helpful.
-
damian from carpentersville, IL
- Easy
- 15 - 30 mins
-
Screw drivers
First i unscrewed the bottom latch to check inside the maching, i then disconected the vertical style pump with pulley from its position and i discoverd a huge crack that was made by a loose pulley. After that i ordered another pulley from this web site easaly installed the pulley and now my maching works like new. The part was less than
... Read more
50 bucks i saved over 200 bucks by not going out and buying a new machine.
Read less
Was this helpful?
Thank you for voting!
Noise from pump
3 of 5 people
found this instruction helpful.
-
Donald from Brielle, NJ
- Really Easy
- 15 - 30 mins
-
Socket set
On a scale of 1 to 5 (with 5 being the most difficult), I would rate this a 2 or 3. It is just a matter of knowing how to access the pump. First I unplugged the washer. Then used putty knife to push in clips to lift up top of washer (the clips are located about 1 inch in from each side). Used socket to remove the two screws holding on
... Read more
front panel. Disconnected the two hoses from pump using pliers to squeeze clips (be sure to have cup or bowl handy because water will come out of the hoses). Lifted up washer and removed belt from pump. Used socket wrench to remove pump and replace with new one. Reattached hoses and belt. Reattached front panel and closed the top of the washer. Everything was easy to access.
Read less
Was this helpful?
Thank you for voting!
My washing machine would not agitate
3 of 5 people
found this instruction helpful.
-
Mike from Woodburn, OR
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I removed the screws on the back panel and took off the panel. Then I turned the knob counterclockwise and removed that.I pulled off the selector knob also. There were two screws holding the timer in place. I removed those and pulled off the plug..... Then installed the new one. My washer is as good as new.
PartsSelect.com sen ... Read more t my parts to me faster than I had hoped. Thank you very much for the GREAT service.
PartsSelect.com sen ... Read more t my parts to me faster than I had hoped. Thank you very much for the GREAT service.
Read less
Was this helpful?
Thank you for voting!
Pump was frozen
2 of 3 people
found this instruction helpful.
-
Frank from Sugar Land, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Socket set, Wrench set
Replacing the pump with the new pump was very easy for me, because of my degree in Mechanical engineering, so I am use to dealing with pumps, engines, gears,etc. However, my wife watched me do the entire job and she is now able to replace this part in the future. The design of the Maytag is very simple to repair, and for that I am very g
... Read more
reatful that we can order the parts and do the repairs ourselves withhout having to call a repairman. This was our first problem after 6 years of smooth operations by this washer.
Read less
Was this helpful?
Thank you for voting!
Pump needed replacing
2 of 3 people
found this instruction helpful.
-
Thomas from Los Alamos, NM
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Removed the front panel to get some light in to the machine. Removed the two hoses connecting the pump to the drain and tub. Removed the three screws holding the old pump in place. Did the reverse to install.
This was a piece of cake.
Thanks for having the parts needed to do this job.
Tom
This was a piece of cake.
Thanks for having the parts needed to do this job.
Tom
Was this helpful?
Thank you for voting!
water leaking under washer
3 of 6 people
found this instruction helpful.
-
paul from akron, OH
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
removed rear acess panel and used pliers to remove leaking hose then reinstalled new hose..
Was this helpful?
Thank you for voting!