CW20P5HC Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Spin cycle out of Balance - Machine walks from wall
1 person
found this instruction helpful.
-
Needham from Leesville, SC
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Disconnect Power. Disconnect supply hoses. Open top by releasing top retainer clips with a thin blade or putty knife. Remove 2 sheet metal screws retaining front cover. Remove front cover. Lay a blanket on the floor and lay the machine over on its side leaving access to the front where the panel was just removed. Take belt off. Remove pu
... Read more
mp hose at bottom of drum. Prop up drum so it is centered in its normal position and not laying to one side. Do this near the lid end. Remove all centering springs - carefully. Drum and transmission assy will now come out through the front opening. Flip drum assy upside down with transmission up. Loosen the screws (do not remove completely - WARNING OF 200 LBS SPRING LOAD!) that clamp the snubber ring to the transmission. Remove the old snubber ring and replace with new. Be sure it is completely under the flange all the way around. Tighten the retaining ring screws. Reassemble all parts in reverse order. Done. Be sure to level the machine per owners manual instructions.
Read less
Was this helpful?
Thank you for voting!
Washer had bad water pump
1 person
found this instruction helpful.
-
Edwin from Eagar,, AZ
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Removed access panel to expose pump, removed drive belt, and old pump, repeated the avove steps in reverse order, tested for leaks and proper operation.
Was this helpful?
Thank you for voting!
Drain pump making load screeching noise
1 person
found this instruction helpful.
-
Danny from Fort Worth, TX
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
I pulled washer out and removed filler hoses from water supply and drain hose and tilted it forward placing three short 2X4's under the washer to keep it tilted forward. Removed
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nut ... Read more driver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nut ... Read more driver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.
Read less
Was this helpful?
Thank you for voting!
broken lid hinge
2 of 4 people
found this instruction helpful.
-
loyce from charleston, SC
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I had my boyfriend take the lid off ,then he took off the two old hinges,one was broken,and the he replaced both lid hinges,daving the good one. it was very simple and quick for him.
Iwill use your service again,thanks.
Loyce Floyd
Iwill use your service again,thanks.
Loyce Floyd
Was this helpful?
Thank you for voting!
Water leaked from bottom of Washing Machine.
1 person
found this instruction helpful.
-
Brandon from Lake Elsinore, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
Removed water lines and drain, removed back panel, removed drain lines from pump. Unscrewed 3 screws to remove pump. attached drain lines to new pump, screwed in new pump, reattached everything. Reinstalled belt (very easy, not like an altenator). done
Was this helpful?
Thank you for voting!
The top load cover would come off in your hand and it was so loose that the lid cover salety switch would not work
1 person
found this instruction helpful.
-
David from WINDHAM, NH
- Easy
- 15 - 30 mins
-
Screw drivers
First I got everything I needed, unplugged the washer. Using the puddy knife I freed the top of the washer by inserting the knife about four inches from each side on front. The machine is in a place where it can not be pulled out far, hence the two by fours. Remove the loose cover, reach in with the stubby and unscrew the screw on both si
... Read more
des. Take the broken cover pins off the cover and install the new ones, put the other hinges in the cover, put the hole cover in place and install the one screw perside, remove wood and close the hole top, your in business , no drinking
Read less
Was this helpful?
Thank you for voting!
it was spinning slowly or not at all
1 person
found this instruction helpful.
-
Louis from FREMONT, NE
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I first changed the belt which helped but it still sounded like it was going to take off through the roof.....I did the pulley and bearing kit in hopes that it would do some good....it went really smoothly with no issues however it did not solve the problem....so it is working and I am going to just ride it out until it quits....thanks
Was this helpful?
Thank you for voting!
Hinge Broken
1 person
found this instruction helpful.
-
Angela from FACTORYVILLE, PA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed screw, replaced hinge.
Was this helpful?
Thank you for voting!
Water leak
2 of 4 people
found this instruction helpful.
-
Joe from Clearfield, PA
- Really Easy
- 15 - 30 mins
-
Socket set
Removed front cover, identified leak, ordered part, saved over half of the cost on part, no service call fee. I feel great!
Was this helpful?
Thank you for voting!
loud grinding sound then washer would shut down then there was water all over
1 person
found this instruction helpful.
-
marilisa from naples, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Socket set
first removed panel from rear of washer removed hoses and drained water in them, removed the 3 screws and removed the belt then removed the pump. Replaced with new one and put back screws,hoses and belt. walaaa.... it works like new!!!!
Was this helpful?
Thank you for voting!
The water was leaking out from the bottom.
1 person
found this instruction helpful.
-
Doris from Plainsboro, NJ
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
My husband took out the 2 screws in the front panel and loosen the 3 nuts from the pump.
The parts was easily removed and the entire job tooked 30 mins.
The parts was easily removed and the entire job tooked 30 mins.
Was this helpful?
Thank you for voting!
Whasher would not drain
1 person
found this instruction helpful.
-
Robert E from Katy, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver
Used a water hose to syfen out the water. Placed hose in the tub. Turned outside facet to fill hose. Undid hose outside and allowed to drain. Pulled pump. Order online ( Delv fast 2 days ) .Replaced pump . Works great . Good luck with yours.
Was this helpful?
Thank you for voting!
washing machine squeaked on the spin cycle
1 person
found this instruction helpful.
-
Jeffrey from Wabash, IN
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
removed hoses and belt. removed 3 screws that secured pump. and then removed pump. received new pump and just reversed the process to repair!
Was this helpful?
Thank you for voting!
The water pump went out
1 person
found this instruction helpful.
-
felicia from Broken Arrow, OK
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
UNPLUG ELECTRICITY. I pulled out the washing machine turned the water off pulled all of your hoses from the back of the machine there may be a mess so you need some thing that will catch the water as it comes out of the hoses. On the bottom of the machine is a belt you have to remove it. Its easy just pull it off. On the back is a panel t
... Read more
hat you unscrew four screws. On the water pump it self you unscrew three screws. Then for the new part you do in reverse order screw your three screws back in put your hoses back on make sure your clamps are tight around your hoses or you will have a leak. Put your panel back on. Put your belt back on. Turn your water on from the wall plug in the electricity and you are done.
Read less
Was this helpful?
Thank you for voting!
Problem manifested as a loud squealing/grinding noise during all cycles.
1 person
found this instruction helpful.
-
Michael from Atlanta, GA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Disconnected both power and hot and cold input water lines. Laid the washer on its front side for access to the bottom. Removed the small access panel from the back of the machine to remove the metal screws holding the pump in place. Removed the single drive belt. New pump installed easily, replaced the belt and access panel. Reconne
... Read more
cted the power and water hoses and everything worked fine.
Read less
Was this helpful?
Thank you for voting!