CW20P5HC Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Tub to pump hose worn out and leaking
1 person
found this instruction helpful.
-
steve from WATSON, MN
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
Replaced the hose. two clamps and retainers. very basic repair
Was this helpful?
Thank you for voting!
Broken Hinge Pins
1 person
found this instruction helpful.
-
Robert from LIVINGSTON, MT
- Very Easy
- Less than 15 mins
-
Screw drivers
I used the putty knife to release the spring clips on the machine lid. They are about 3" in from the side of the machine. Then I lifted the top of the washer up holding the lid in place. I then used a screw driver (torx) to remove the hinge from the bottom of the washer top. The lid should come right off. Then I the removed the broken hin
... Read more
ge pins from the back of the lid with a screwdriver and replaced with the new parts. There is a little tab that the pin fits in the lid to assure you have the pin installed correctly. Then I slid the hinge back on the pin and reversed the process reinstalling the hinges and closing the top of the machine over the spring clips and your done. Very easy repair that I completed in less than 15 minutes.
Read less
Was this helpful?
Thank you for voting!
Activator device broken off
1 person
found this instruction helpful.
-
Sonya from VAIL, AZ
- Very Easy
- Less than 15 mins
-
Screw drivers
Easy repair - with the use of a phillips screwdriver, simply remove the old device and replace with the new
Was this helpful?
Thank you for voting!
Worn belt
1 person
found this instruction helpful.
-
Richard from OXFORD, NY
- Really Easy
- Less than 15 mins
Rolled the old one off and rolled the new one on.
Was this helpful?
Thank you for voting!
old belt broke and fell off
2 of 4 people
found this instruction helpful.
-
Tim from New London, OH
- Really Easy
- Less than 15 mins
tipped the washer back, laid on the floor, and wrapped new belt around 3 pulleys. everything works as before.
Was this helpful?
Thank you for voting!
Had the screeching noise for a few days and kept using it until it finally didn't do anything. From youtube i was able to diagnose using other peoples experiences and discovered the part i need by looking at the pictures from the model #.
1 person
found this instruction helpful.
-
Rita from Rodarte, NM
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I had my 12 year old son climb to the back and he took off all the screws necessary in the back and took the part completely off. We ordered the part and waited for it to come in. We replaced the part, the screws and honestly, the only thing we had trouble with was replacing the small cover where the hoses stick out of the washer. Was
... Read more
an easy efficient experience that may have saved me $300.00+ dollars. Thanks to my 12 year old son we got her fixed up. The washer works like brand new.
Read less
Was this helpful?
Thank you for voting!
Water dripped into washer even when off
1 person
found this instruction helpful.
-
Larry from Mansfield, MA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Hardest part was figuring out how to get to the water valve. Turned out that the way in was from the top. All I had to do is remove two screws at the back of the top panel, and then unclip the front edge of the top panel (use a thin screwdriver to press in on the clips from the front of the machine). From there, it was easy to reach dow
... Read more
n inside and remove/replace the valve.
Read less
Was this helpful?
Thank you for voting!
Loud grinding noise when I ran the washing machine
1 person
found this instruction helpful.
-
Eman from Wood Dale, IL
- Easy
- 30 - 60 mins
-
Pliers, Socket set
It took long because I did not know where the noise is coming from and I took the sides off. I went to the store and bought a new washing machine. Delivery was scheduled in 3 days. I decided to lay the machine on its side and look underneath. I pulled the belt off the 3 pulleys and turned each pulley by hand. The one runing the pump was s
... Read more
tiff and noisey. I ordered the part, arrived in 2 days, installed it in 15 minutes and closed the machine in 30 minutes, then cancelled the order of the new machine and saved $500.00
Read less
Was this helpful?
Thank you for voting!
pulley was scraping bottom of pump
1 person
found this instruction helpful.
-
Brian from Granbury, TX
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
First , I unlocked top cover and propped; removed front cover. tilted machine back propping front. pump is at lower right corner, removed both hoses, removed belt and three screws. reversed order completing job. You will have some water leakage removing hoses.
Was this helpful?
Thank you for voting!
Washer making noise during cycles
1 person
found this instruction helpful.
-
Nat from Baton Rouge, LA
- Really Easy
- 30 - 60 mins
-
Nutdriver
I moved the washer out from the wall. unplugged washer, turned off water. Took off rear plate exposing pump. Disconnected hoses, using dry/wet vac to catch water. Took out three screws holding pump to base of washer and removed pump, belt slipped right off. Set new pump in place and put in screws. Connected hoses, put rear plate back on.
... Read more
Tilted washer back and installed belt on pulleys and motor. Turned on water, plugged in washer, started to wash clothes. Washer works fine and QUIET. I have yet to find the model number on my Maytag washer. I ordered the pump by sight (good pics).
Read less
Was this helpful?
Thank you for voting!
Noise
1 person
found this instruction helpful.
-
Marylou from Old Forge, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Wrench (Adjustable)
I changed the piece easily
Was this helpful?
Thank you for voting!
Wouldn't spin after rince
1 person
found this instruction helpful.
-
joe from LAWRENCEVILLE, NJ
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Followed the great instructions on your video
Was this helpful?
Thank you for voting!
crack in tub hose causing washer water to spill on to floor
1 person
found this instruction helpful.
-
Bette from S BARRINGTON, IL
- Easy
- 30 - 60 mins
-
Pliers, Socket set
raised the top of the washer to get at the front panel screws. Removed the front panel. Removed the cracked hose and installed the new one. Reinstalled the front and top panels.
Was this helpful?
Thank you for voting!
Water leak
1 person
found this instruction helpful.
-
Stephen M. from LEWES, DE
- Really Easy
- 30 - 60 mins
-
Socket set
Removed front panel by releasing spring clips with putty knife and removed two screws with a ratchet and 5/16” socket. Removed rear access cover with a ratchet and 5/16” socket. Removed and replaced tub to pump hose. Loosened clamps on each end of hose with channel locks.
Re installed rear access cover and front panel.
Re installed rear access cover and front panel.
Was this helpful?
Thank you for voting!
My 24 year old Maytag performance washer started occasionally not agitating. Eventually it did not agitate at all but would spin.
1 person
found this instruction helpful.
-
Loretta from LEBANON JCT, KY
- Really Easy
- 30 - 60 mins
-
Screw drivers
The lid switch is on the right side top of the washer under the lid. I took a putty knife and found the clips that hold the top of the washer and pushed them to release it. I then lifted it up to fully see the lid switch. I unplugged the washer from the wall socket and took out the 2 screws that holds the lid switch in. Then unplugged the
... Read more
lid switch from its electrical connection and put the new one in its place. Washer is working great so far.
Read less
Was this helpful?
Thank you for voting!