EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

CW20P4A Crosley Washer - Instructions

All Instructions for the CW20P4A
106 - 120 of 272

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
machine woulden't spin properly
1 of 3 people found this instruction helpful.
  • Richard from Ponte Vedra Bch, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver
diagnosed a loose belt-- ordered and received same -- installed and set to proper tension that was simple.
Was this helpful?
Thank you for voting!
Pump was making a grinding noise.
1 of 3 people found this instruction helpful.
  • Daniel from Hinsdale, IL
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
I tilted the machine on it's back to remove the drive belt. You could feel the friction in the pump when you turned the pulley. I set the machine back down and removed the back cover (4 screws). I removed the two hoses with a pair of pliers. I used a small socket set to remove the three mounting screws. I ordered the pump. I reversed the process to put it back together. It took about 35 minutes to determine what the problem was and to remove the pump. It took about 20 minutes to put it back together.
Was this helpful?
Thank you for voting!
Washer was leaking water.
1 of 3 people found this instruction helpful.
  • Steven from Atlanta, GA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Socket set, Wrench (Adjustable)
Removed front of washer following instructions on partselect.com (used putty knife to release catches). Removed hoses and belt from pump, then removed and replaced the pump. Reattaching the belt was the only awkward task.
Was this helpful?
Thank you for voting!
Noisy Pump
2 of 7 people found this instruction helpful.
  • Frederick from Yuma, AZ
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
I placed the washer on a couple of work-horses so I could have access to the belt underneath. Then I used my nutdriver to removed the lower back panel. Disconnected both of the hoses, and removed the pump with my nutdrivers. Placed the new pump in place, placed the belt back on the pump's pully, tightened down the pump. I then plugged in the washer and put a little water in the washer to test that everything was working. After confirming that everything worked, I replaced the lower back panel and put the washer back in business. 30 minutes from beginning to end ... and a good time was had by all.
Was this helpful?
Thank you for voting!
Bearing on pump making noise and would go out soon.
0 of 1 people found this instruction helpful.
  • Marcus from Camarillo, CA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I diagnosed the bearing by putting a 3/4 inch rubber hose up to my ear. I pointed it around until isolating the noise to the pump. The bearing was not servicable without replacing the pump. After diagnosing the problem I ordered the part. Getting the part from PartSelect.com was a snap. It arrived in one day. In 15 minutes I had it back t o gether and working quiet and smooth.
Was this helpful?
Thank you for voting!
Water would not drain and tub would not spin.
0 of 1 people found this instruction helpful.
  • Larry from Waukesha, WI
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
I had to raise the top of the washer and take off the front pannel. It was not too hard to replace the pump except that it was in the back corner and it was hard to reach the bolts to remove and install the new pump.
Was this helpful?
Thank you for voting!
Vibration
0 of 1 people found this instruction helpful.
  • Richard from Jacksonville, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Troubleshoot problem, removed front, removed drive belt, removed pump with pulley. Note, new pump did not have black plate, installed worked great.Thanks
Was this helpful?
Thank you for voting!
Washer Walking Across Floor,From Being Off Balance
0 of 1 people found this instruction helpful.
  • Kenneth from Griffith, IN
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
1- Unplug unit 2-disconnect water hoses 3-put unit in open area so you can work on it. 4-Open top cover with screw driver 5-take off front cover with appropriate socket 6-lay unit on it back to get access to the drive belt (take off). And take off water hose with plyers. 7-With vise grips take off the six springs. 8-Take tub assy ou t,and lay it on the floor upside down. 9-Loosen the screws to take out the old snubber ring, note ( when lossening screws,keep your finger on the bottom of the screw ,so you can feel how far to back the screws out,just enough to have access to the snubber ring,to take out,and install new one. )Remember not to take screws out completely. The unit is under spring tension. 10-Put washer back together in reverse order,and problem solved!
Was this helpful?
Thank you for voting!
drive pulley broke off from drain pump
0 of 1 people found this instruction helpful.
  • John from Pomfret, MD
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Raised washer. Identified problem. Removed from panel, gaining access to drain pump. Removed hoses, replaced pump. NOTE: I used blue Loctite on pump mounting bolts. Reinstalled from panel, lowered washer, cleaned drum. Ran one (1) cycle with hot water and bleach ONLY.
Was this helpful?
Thank you for voting!
Washer going out of balance
0 of 1 people found this instruction helpful.
  • Brian from Rock Hill, SC
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Tilted washer back and removed belt
Lifted front of top and propped up
Unscrewed two screws and removed front of washer
Disconnected two drain lines from tub
Disconnected 6 springs from tub
Removed tub
Popped off bottom plastic cap
Removed locking ring
Slid off gear from shaft
Unbolted screws f rom snubber support ring
replaced snubber
Put everything back together in reverse order

Worked like a champ!!!!!
Was this helpful?
Thank you for voting!
Pulley Bearings Siezed; Pump Quit
0 of 1 people found this instruction helpful.
  • Robert from Columbia, MO
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Turned it over to my 35-year old son who removed pump and pulley assembly and the old drive belt, then simply replaced with new assembly and belt from PartSelect! Could not have been easier - from my viewpoint.
Was this helpful?
Thank you for voting!
Needed to replace the water pump
0 of 1 people found this instruction helpful.
  • Theresa from Zanesville, OH
  • Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench set
The Clamps for the hoses were difficult to get to, otherwise was a simple replacement job, involving clamps and screws and bolts.
Was this helpful?
Thank you for voting!
washer shaking
0 of 1 people found this instruction helpful.
  • Jerry from Troy, PA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
took drum out replase snubber put drum back in
Was this helpful?
Thank you for voting!
Washer noisey during spin dry
0 of 1 people found this instruction helpful.
  • Edwin from Green Valley, AZ
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set, Wrench set
Had wife balance washer on front edge while I accessed working parts from bottom of washer. Removed drive belt and turned agitator pulley, transmission pulley and drain pump pulley by hand. Drain pulley hard to turn and shaft had play in it. Ordered new drain pump and replaced upon receipt. Very few fasteners to remove and replace pum p assembly. Drive belt was easy to remove and replace. Recommend also replacing drive belt on a washer this old.
Was this helpful?
Thank you for voting!
no cold water
1 of 4 people found this instruction helpful.
  • juan from moreno valley, CA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Socket set
I pulled the top ofthe washer up, I disconnected the cold and hot water hoses, took the 2 bolts off with a socket and pulled the water valve from the top. I used the pliers to take the pressure ring off and pulled over flow hose off. I pulled the four wires off with pliers. Put the new water valve in reverse order...easy.
Was this helpful?
Thank you for voting!
All Instructions for the CW20P4A
106 - 120 of 272