EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

CW20P4A Crosley Washer - Instructions

All Instructions for the CW20P4A
91 - 105 of 272

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water leak
2 of 4 people found this instruction helpful.
  • Joe from Clearfield, PA
  • Really Easy
  • 15 - 30 mins
  • Socket set
Removed front cover, identified leak, ordered part, saved over half of the cost on part, no service call fee. I feel great!
Was this helpful?
Thank you for voting!
pulley was scraping bottom of pump
1 person found this instruction helpful.
  • Brian from Granbury, TX
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
First , I unlocked top cover and propped; removed front cover. tilted machine back propping front. pump is at lower right corner, removed both hoses, removed belt and three screws. reversed order completing job. You will have some water leakage removing hoses.
Was this helpful?
Thank you for voting!
Loud grinding noise when I ran the washing machine
1 person found this instruction helpful.
  • Eman from Wood Dale, IL
  • Easy
  • 30 - 60 mins
  • Pliers, Socket set
It took long because I did not know where the noise is coming from and I took the sides off. I went to the store and bought a new washing machine. Delivery was scheduled in 3 days. I decided to lay the machine on its side and look underneath. I pulled the belt off the 3 pulleys and turned each pulley by hand. The one runing the pump was s tiff and noisey. I ordered the part, arrived in 2 days, installed it in 15 minutes and closed the machine in 30 minutes, then cancelled the order of the new machine and saved $500.00
Was this helpful?
Thank you for voting!
Washing machine began making a screeching noise but only during the spin cycle - when it was emptying the water from the tub. After a few uses the machine just stopped working.
1 of 2 people found this instruction helpful.
  • Patricia from Modesto, CA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
The pump was easy enough to replace. Access panel in the back and 3 screws and it was off and back on in less than 20 minutes. It was putting the belt on that gave me the most trouble even though one of the pulleys moved to allow for easy replacement it did not move enough. It took me another 30 minutes just to get the belt on. I fina lly decided to place the belt on the two smaller pulleys and save the larger one for last and it went on with no trouble at all. Learn from my error =]
Was this helpful?
Thank you for voting!
discharge pulley assembly bearing going out on it.
1 of 2 people found this instruction helpful.
  • Milton from bartlett, IL
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Went to website, looked up make and model, looked at photo's discription, studied it, and then went in and removed front panel, turned off water, removed clamps holding hoses too dishcharge pump, mopped up water, and then just reinstalled new piece, the way the old came out, re attached belt to pulley assembly, turned water back on, and d id a test for leakage and wala washer back in working order in less than an hour, and saved hundreds of dollars with out maytag repair man.
Was this helpful?
Thank you for voting!
Washer making loud noise and tub off balance
1 of 2 people found this instruction helpful.
  • Hollee from Rancho Mirage, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I followed Gary from Sioux City IA instructions. Very well explained.
Was this helpful?
Thank you for voting!
Old hot water inlet hose had budge at both ends.
2 of 5 people found this instruction helpful.
  • Jimmy from MEMPHIS, TN
  • Very Easy
  • Less than 15 mins
  • Pliers
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this helpful?
Thank you for voting!
water not draining
1 of 2 people found this instruction helpful.
  • FRANK from CHULA VISTA, CA
  • Really Easy
  • 15 - 30 mins
  • Socket set
changed drive belt and saved me from buying new washer,,working like bland new again ...many thanks
Was this helpful?
Thank you for voting!
The Pump Went Out & Water Was All Over My Floor..
1 of 2 people found this instruction helpful.
  • BILL from DIX, IL
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Unscrewed the front panel. Then took pump out & put new one in. . . . . Thank you part select. Com. . . Super fast shipping. . .
Was this helpful?
Thank you for voting!
Made noise during washing and rinse cycle
1 of 2 people found this instruction helpful.
  • Jose from Elizabeth, NJ
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
It was easy to replace the water pump
Was this helpful?
Thank you for voting!
Water pump replacement
1 of 2 people found this instruction helpful.
  • Lon from Morton Grove, IL
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Socket set
Reverse the process to install new pump
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump

Reverse the process to install a new pump

Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.

The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.

This was is 1st time we used your server but it won’t be the last!

Kudos to the entire staff and please…keep up the good work.

Sincerely,

Lon Thomas
Was this helpful?
Thank you for voting!
Started making loud screeching noise(bad Bearing)
1 of 2 people found this instruction helpful.
  • Michele from Lebanon, PA
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Socket set
Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.
Was this helpful?
Thank you for voting!
Made noise on spin cycle
1 of 2 people found this instruction helpful.
  • Les from Moneta, VA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Took off belt and ran motor. No noise. Then took off drain pump and spun it by hand and felt rubbing on one spot. I figured the bearings were going bad, so I ordered the parts and replaced them.
Was this helpful?
Thank you for voting!
machine was starting to make noises when spinning
1 of 2 people found this instruction helpful.
  • Virginia from Rockford, IL
  • Really Easy
  • Less than 15 mins
My husband unhooked the water lines, unplugged the washer and remove the waste water hose, then we tipped it over and easy as pie the belt came off and the new one went right back on. I did not see any tears or breaks in the old belt, but it was stretched out a bit, and the washer is once again quiet. This also gave me an opportunity to clean under the washer, which we all know we don't do unless we have to. Cheap, quick, and easy fix for someone to do there self.
Was this helpful?
Thank you for voting!
noisy out of balance during spin cycles
1 of 2 people found this instruction helpful.
  • Ronald from Wading River, NY
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Socket set
I followed the instructions that other posters suggested. The springs were the toughest part to remove and reinstall. Having my wife push the tub enabled me to use vice grips to get them back on. Read about the coins or washers to spread the springs too late... would have helped. Running a wash now and it's spinning great and no noise !
Was this helpful?
Thank you for voting!
All Instructions for the CW20P4A
91 - 105 of 272