CSK20GABGAD Hotpoint Refrigerator - Instructions

Removed food and trays from door. This took longer than the actual repair. Removed top hinge cover (1 phillips screw) and top hinge (2ea 5/16" hex bolts). Removed door, replaced hinge assembly on refrigerator (2ea 5/16" hex bolts)which included a new hinge cam (they don't tell you this, but the cam is included in the assembly so you don't ... Read more need to order a seperate cam) I now have a spare cam. Piece of cake...your mom could do it!!

I read the details and bought the pair, as directed from other bloggers. I got the hinge piece, followed others advice and had it all done in not time! Saved a lot of money and will use this website again!

very easy, thanks for the great selection for parts.

Removed all items from the door shelfs.
With the door open, picked up the door and slid it upward as far as it would go. Asked wife to place a stack of books under the door to keep it at the proper height. Removed the lower hinge pin assy. remved the door stop. Installed new componets and reinstalled the door stop. The door was now ... Read more level with the freezer door.

I had to remove the top hinge of the door and shut off the water supply to the automatic ice maker. I then unhooked the water line and pulled it through the guide as I took the door off. Once the door was off, I removed one bolt with the nut driver and replaced the cam. I reversed the above actions and replaced the door. It is very i ... Read more mportant to adjust the door so the seal fits tightly and evenly all round the door. It was a relatively simple procedure that went very smoothly.

After reading other posted comments,I ordered a new hinge assembly set ps290199. My helper and I removed the door and laid it on the kitchen table. While he replaced the hinge on the refigator,I replaced the cam on the door bottom. We re-hung the door and completed the job in 15 minutes with the door closing like it did when new.

Same as the others, just propped the door up and took off the upper and lower hinge parts and replaced them. One note: the old hinge was so torn up that some of the shims were partially destroyed. Since I didn't order the shims, I had to do a little machining. It might be a good idea to order shims if there is ant doubt.
P.S. With no ... Read more rmal shipping, the order arrived in 2 days!

Removed door and replaced bracket assembly. Door works like new. Self closing and sealing properly.

I simply followed the excellent video, once I discovered the lower door hinge was the problem. Part Select was amazing! A $25 part and 15 minutes saved me $1,200+ ... the price of a replacement refridgerator. Thank you!

I watched the video on your web site first.Then I proceeded to do the repair exactly as the video showed. Very easy!!!!!

1.Emptied the stuff from inside of the fridge door.
2.Using a phillips screw driver I removed the plastic cover over the top hinge.
3. Using a small ring spanner I removed the two bolts holding the top hinge (pin), removed the hinge and lifted the door off the bottom pin.
4.Using the same spanner I removed the bottom hinge ... Read more containing the broken plastic cam.
5.Replaced the broken hinge with the new one and put a little grease on the hinge pin.
6.Placed the new plastic cam on the hinge pin and refitted the door.
7.Replaced the top hinge and plastic hinge cap, Job Done!

A couple of points a) When your plastic cam needs replacing, always buy the hinge pin & plastic cam. The pin has a plastic cam welded to it and as this is the partner of the plastic cam it will also be worn so you should replace them as a pair.
b) You will spend more time cleaning the 'out of the way' parts of the fridge than actually carrying out the repair.

My fridge is now as good as new.

Removed the upper hinge assembly. Removed the door. Removed the kick plate. Removed the old hinge assembly and installed the new one.Replaced the other broken cam on the door bottom. Then,reinstalled door to fridge and reinstalled the top hinge. PS/cleaned and lubed both upper and lower hinges.

Lifted the door while closed into position even with freezer door. Then put srap pieces of wood under door to hold into place while I removed the old hinge assembly and replaced with the new one. The door works good now. Make sure you replace both peices as they will both be worn.

Discovered the door cam was broken. Did a search, found the part on PartSelect.com. Read the repair stories and realized I need two cams. So I just bought the whole hinge assembly figuring it would be a little easier and did not cost that much more.

Put blocks under the door, unbolted the old hinge from the refrig, and the old ... Read more cam from the door. Replaced them with the new parts, and I was all set. Took about 15 to 20 minutes. Had my wife stand by the door just in case it fell, which I knew it wouldn't.

First removed plastic cover off top hinge with phillips screwdriver. Used nut driver to loosened screws on upper hinge to 1/2 inch out and then used wood blocks to shim up door as high as possible while still in closed position. Used socket wrench to remove lower hinge and fitting from bottom of door, while still closed. Installed new l ... Read more ower hinge and door fitting with socket wrench. Lowererd door to sit on bottom hinge and then adjusted position of top hinge before tightened those screws with nut driver. Reinstalled plastic cover. Piece of cake!