CS980ST3SS Hotpoint Range - Instructions

it went well as compared to getting a new ~~800$ cooktop and ~~150 to install, I took a shot for 30$ bucks and it worked great!! problem solved and great support ! !! thanks for all your help

Very easy to replace. So easy even a man can do it.

Slide the rang out to access the 240V plug & unplugging it. Removed the sheetmetal cover from the rear of the range to access the slip on wire plugs to prevent damaging the insulation. The insulation would be damaged if pulling them through the opening in the oven wall with the plugs attached to the element. Removed the racks from the o ... Read more ven. Unscrewed the retaining screws holding the element to the rear wall of the oven, lifted damaged element out and reversed the process for instillation. Perfect opportunity to clean underneath and behind the range.

Used nut driver and removed the 4 nuts holding the broiler. Pulled electrical wires of old broiler Received new unit and it was just as easy to replace. Thank you for assistance.

Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.

Turned off juice
Pulled stove from wall
Unscrewed 2 screws to loosen range top
Lifted n propped top
Unplugged 4 wires
Unscrewed burner assembly
Installed burner-reversed steps to reassemble

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks

I removed the rear lower cover. Disconnected the terminals from the heating element. Removed 2 screws from the heating element from inside the oven. Removed the heating element. Reinstalled everything in reverse order.

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Really easy. Part came in rapid time and was the right part. Went on web and got instructions with video how to install.

Disconnect stove electrical connection. Removed 2 bolts common to the upper stove top cover. Disconnected 4 wires from burner element along with 2 retaining clips.
Removed burner element and replaced with new element. Reinstalled 4 wires and 2 retaining clips. Lowered stove top cover and reinstalled 2 bolts. Connect stove electrical ... Read more to wall outlet. Turn on burner element and verify that it works.

Pull out wires & replace element by putting wires back in then tighten...done!!!!

First unplug range from electrical outlet!
Removed screws under front edge of stove top, propped it open with long paint stick, pried clips off of the element, unplugged and plugged in new element, push element back into clips, closed top on stove, plug back into socket, tested new burner, put screws back in under top front edge of ... Read more stove top!!!

First, disconnect electrical power to the stove by turning the main fuse to the off position. Confirm that there is no electrical power in the stove. The ceramic top is held by 10 screws that are closest to the ceramic surface. Other screws hold other parts of the stove and not need to be touched when opening the stove. Once the ceram ... Read more ic surface is off there is access to the burners and the various lights and switches. It is important to determine whether it is the burner that is defective or the switch. Inasmuch as the switch has many moving parts, the switch is more likely to be the defective part. Check the switch by gaining access to the switch connections. There is a metal frame held by two screws on each side in the outside of the stove (same area where the initial 10 screws were removed to separate the ceramic surface). Remove these screws and flip the switch assembly so all the wires and cables are accessible. I checked the switch with a continuity tester and by trial and error determined that there were two connections that in all the remainder three switches had continuity when the switch was in the on position while the suspect switch did not. Replaced the suspect switch by pulling the wires and replacing them in identical positions in the new switch (a smartphone camera became very useful to remind me were exactly each cable's connection was). Restore power by turning the fuse to the on position. Check that the burner lights up. If not, change the burner as well. Same simple procedure of disconnecting and connecting cables to the burner). Make sure to disconnect power before working on the burner. Replace the screws that hold the switch assembly. Replace the ceramic top. Replace the screws. Set stove back in its hole. Reset fuse. Total time: 35 mins. Total cost: Approx $25.00 (switch + delivery). Quoted repair by local appliance repair service: $487.50. No contest. Next project is to fix a leaky water dispenser in the refrigerator.