CS2138C (2006-01) Jonsered Chainsaw - Parts

This Bar Pin Adjuster is an OEM part used to adjust the tension on the bar, which loosens or tightens the chain. It attaches to the slot in the bar, and the chainsaw bar adjusting screw. Installation is rated as "Easy" and requires a screwdriver. Refer to your make, model and diagram to ensure this part is correct.

This is an authentic OEM part for use with Craftsman Chainsaws. The recoil starter repair kit replaces the parts of the engine\\\'s recoil starter susceptible to normal wear. The most common reason for replacing the recoil starter repair kit is if the engine won't turn over when starter rope is pulled the Starter rope pulls too easily (an...Read mored without resistance) the Starter hub is not engaging the flywheel or the Starter hub is not turning with the pulley (when the rope is pulled). This part includes starter pulley the assist spring and the starter hub. Here is a list of tools that are needed to install the recoil starter repair kit Phillip's screwdriver, Torx drivers, long-nosed pliers, and scissors or wire cutters (optional).

This is a genuine OEM sourced replacement part designed for use with Poulan chainsaws. It is used to attach the cylinder shield to the main body of the chainsaw. This screw is made out of metal and it is sold individually. To remove or install this screw you would need a T-25 torx screwdriver.

The chainsaw starter rope is a three-foot-long white rope that is approved by the original equipment manufacturer, and which wraps around the recoil pulley and is pulled to start the engine. Installation is rated as "Easy" by customers and requires a screw driver, pliers, and torx screwdriver. If the rope breaks it should be replaced. Ref...Read moreer to your make, model and diagram to ensure this rope is right for your machine.

This is an authentic replacement part supplied from Poulan. It is generally used with gas powered chainsaws. This nut in conjunction with a bolt (sold separately) helps to secure air filter and carburetor. Requires a wrench installing/removing this item. It is sold individually.

This is an OEM part sourced directly from the manufacturer. The chain brake kit is designed for use in Craftsman chainsaws. This part is made of metal and high-quality plastic, and is used to halt the motion of the chain. You may require a screwdriver or Allen wrench when replacing this part. This item is sold individually.

This is a genuine replacement part manufactured for use with chain saws from Craftsman. This part secures the bar to the clutch. It is recommended to review your models diagram to verify the parts compatibility. This bar mounting plate is made of metal and sold individually.

This is a Genuine OEM replacement part used on Poulan Gas Chainsaws. This item is made out of Metal and it is Sold Individually. A centrifugal clutch is a part that uses centrifugal force to connect two concentric shafts, with the driving shaft nested inside the driven shaft. Today's centrifugal clutches will function even when they shoul...Read moredn't, far beyond the point of when they need to be replaced. Keeping an eye on equipment performance will determine when the centrifugal clutch requires attention. Please note Clutch Drums is Sold Separately. To replace this item you would need a Wrench and Pliers.

This is an authentic Craftsman replacement part that has been sourced from the original manufacturer to be used with chainsaws. The oil cap connects to the saws chassis by covering the oil fill spout to prevent spills and to prevent contaminants from entering the oil tank. This item is available as an individual replacement part. Tools are not necessary to install this item.

This is an authentic Craftsman replacement part. The metal piston ring is compatible with many chainsaw devices. This part has been designed to work as a seal between the piston and the engines cylinder wall. If piston ring is broken or worn, it will cause gases to escape and enter the crankcase. In turn, this would create low compression...Read more and a decrease in power, possibly stalling out the engine. A set of wrenches, pliers and a screwdriver are needed in completing the repair. This item is sold individually.

This OEM bar adjustment retainer is a metal component that securely holds the adjustment screw and pin in place, allowing you to adjust the chain tension. It is typically located near the front of the chainsaw, close to the guide bar. If the guide bar is over-pressured, the retainer can become stressed and fail, causing it to ride up on t...Read morehe screw. Signs of a damaged retainer include visible breaks or deformations. You may also have trouble in tightening or loosening the chain, as the screw may become loose during adjustment. To remove a faulty retainer, remove the side cover by loosening the nuts and the tension screw on it with a socket. Unscrew the guide bar and replace the damaged retainer. When installing the new retainer, ensure the cone points towards the adjustment pin. Please note that the replacement retainer is sold separately from the guide bar and adjustment pin.

This is a genuine manufacturer approved replacement part designed for use with chainsaws. It is a standard hardware which has multiple applications based on your equipment. Please refer to diagrams of your unit for correct application. This is a metal phillips head screw which is sold individually.