CRE9530BCM Maytag Wall Oven - Instructions

Turn off breaker.
Unscrew old element, disconnect wires.
Connect wires to new element, tighten screws.
Breaker back to ON.
Done.

switch off the range. undo the two screws & unplug the two tabs. Replace with new element, connect two tabs, screw back in place. done!
recieved my replacement part the next day after ordering

I first shut off the breaker to the stove - safety first!

I used a phillips screw driver to remove the two screws that held the old element in. Then I pulled the old element out and used the pliers to remove the electrical connections. I put the new element in, made the electrical connections and secured it with the screws. ... Read more After restoring powere via the breaker, we tested the stove and it worked. Just call me the Maytag Man!

Watched the video that was available and followed the instructions. Unplugged the stove first,removed the old element, and put the new one in. Video was very helpful and the installation was very easy. Was done in about 10 minutes.

First I removed the two screws that hold the element in place. I then pulled the element out aobut 3 inches and disconnected the wires.

Turned off power, removed 2 screws, un-hooked the connections, them put in the new element in reverse order.

I received the new element on the third day, followed simple directions, and voila! I'm baking again.
First I unplugged the stove. Important!. Then with a phillips head screwdriver I removed the two screws at the back of the oven. The transition from busted to new was easy because there was a slide-in connection to the wires, not ... Read more screws. The best advice was sticking duct tape on the wires so they wouldn't go back into the inner sanctum before I was able to attach the new element. Hey, I'm a 72-year-old grandma, and it was easy!

First I turned off power to the range at the fuse box (very important-The last time I didn't do this and ended up paying a repairman $150.00 to replace the damaged connectors). I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then connected the new ele ... Read more ment, pushed the element back in and replaced the screws. Turned the power back on and tested the element. The whole job took about 30 minutes because I had trouble disconnecting the old element. I used the flat end of the scrapper to push against the connector while I pulled the element out. Normally it would take only about 15 minutes.

I let my husband to the work...But it was very easy. I could have done it! He removed the screws, pulled the wires off previous element. Reattached the wires to the new element and screwed the ends back in place.

Removed 2 phillips screws, unplugged 2 wires, threw away old element. Installation of the new element was just as easy but in reverse order. Piece of cake!

installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.

I unplug the stove first. Then took off two screws that held the bake element in place. Pulled off the connectors using the pliers. Had to use pliers because they were really snug. Plug in the wires to the new base element. Crimped down the connectors a little bit to make sure they were snug. Inserted the bake element back into the ... Read more holes at the back of the oven. Put the two screws back in. Plugged the oven back in and turned it on to make sure it worked. Lastly, tossed the old bake element in the trash. Really easy job. Glad I didn't pay anybody to do this.

Took two screws out unplugged the element and plugged the new one in and replaced the screws and turned the breaker back on. Works great...Piece of cake..jk

First throw the breaker on the stove. Remove two screws in back of oven then slowly pull out loosen the wire attachements ......got new part in 2 days just as simple reverse the removal directions.,,,I am over 60 female and it was simple.

Pulled range out from cabinet-wall to get to back side, everthing was clearly exposed tlhen. Just a matter of installing new fixture, putting back on, reconnected power source - put range back in proper place.