CGS3760ADA Magic Chef Range - Instructions

slide out stove remove rear cover (6 screws) to access sensor plug . remove two screws from inside oven area and remove part,replace in reverse order.

I used the other good burner assembly to isolate the problem to the igniters or the igniter block. I ordered both parts from Parts Select. They shipped the parts promptly and after 10 minutes of install time, the burners worked flawlessly.
Thank You Parts Select.

Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in ... Read more each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.

Turned burner about a quarter of a turn, lifted, disconnected wires, connected them to a new burner and replaced it.

Unplugged the stove and unscrew the 2 screws on the thermometer inside the stove and unplugged the white plastic in the back of the stove and I had to put the new extra piece that came with the sensor kit as it was needed because the socket were different.

Took the old levelling leg out and screw the new one in.

installation was very simple and took less than 5 minutes. first unscrew the burner cap and then remove the 2 wires. to replace reconnect the 2 wires to the new cap and twist cap into place-simple.

it was actually pretty easy, it took about 20 minutes to fix, i had to unscrew the bottom portion of the oven to get to the Igniter on the bottom, then unscrew the Igniter, take off the old pice, and snap the new one in, put it all back together, and that was about it, i had dinner done by the time my husband got home from work. thanks

Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old ... Read more gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.

The flame holder twists about 1/2 inch to left and lifts off. I removed the two screws that holds the igniter on and removed it and installed the new igniter.
There was one complication: when I put it back together, there was no spark. I removed the ground wire and cleaned and scraped it and replaced it and still no spark. But, for n ... Read more o apparent reason the spark returned and has been okay since.

unplug unit remove rear panel screws lift up stove top remove top two screws remove panel remove two hinge screws remove replace hinge and follow in reverse order

Shut off gas supply
Pulled stove away from wall removed spark ignigtor box .
Installed new one .
No problem.
Good for another 10 years

took out racks removed 2 screws holding igniter removed 4 screws on back of stove and unplug igniter. reversed the order installing the new one

Took the bottom out of oven then removed and replaced with the new part. VERY EASY! I'm a 70-year-old woman and do quite a few home repairs myself.

From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.