CGL2000RW169 General Electric Dryer - Instructions

The gentleman knew what the problem was, sent the right part, and I looked like I was smart.

Good thing my husband is so handy. This part was very difficult to get to. Basically, he had to take apart almost the whole dryer. There is no access door so the side panel had to be removed, but before you could do that the front panel and door had to come off, then the top of the dryer. Keep track of the screws, we had a few leftover! ... Read more But the dryer works great again and we hope to get several more years out of it. We've had no problems with it until now and it's over 15 yrs. old.

The front panel must be removed on this unit after turning off power supply. First open dryer door and.remove the 2 screws facing upwards. Disconnect the light if applicable, using a putty knife insert under top to free the top from front cover this is to push on the retaining tabs that are inboard of the screw areas that you have removed ... Read more . Raise top panel. It is hinged at settings panel. This is completely removable by sliding to the side Then locate the 2 small screws located in the side panels near the top. Once these are removed the front cover will be able to be removed carefully moving forward while supporting the drum you know can see the parts that need replacing on the lower right. Take a picture as reference!! With power off remove the retaining clip that holds the dryer solenoids in place using a short stubby screwdriver. One at a time replace solenoid by lifting and disconnecting the wires (they snap on.) Good time to also check for excess lint and clean out. Check drum bearing and glides..reassemble in reverse order ..

drive belt gone, replaced belt and bearing

Unplug the dryer. Remove top panel (remove two screws on the upper inside edge of the dryer door). Lift the front panel from front (tabs and slots at the back) and lift off. Remove the front panel (remove a screw from each side - top/front). Front panel sits on two feet at the bottom, tilt it forward from the top and lift it up (careful n ... Read more ot to damage the electrical connection at the bottom left side). I found the dryer had another damaged part (plastic guide that the Slide WH and the Drum Slides connected to was badly worn). After ordering the additional part I attached the slides (white and gray) to the guide. Set the front panel back on the two feet and tilt it back into place (you'll need to slightly raise the drum back into position - easy). Replace the two screws that connect the front panel. Replace the top cover. The whole repair took less than 1/2 an hour including the time it took to vacuum out the dust. Total cost, about $35!

Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.

unpluged the dryer removed the rear panel pry off control knob removed two scews for timer moved the two wires from old timer and put on new timer put back in with the two screws put knob on install rear panel plug in dryer tested it to make sure it worked properly i am done.

Watched a video online on how to replace the belt, it pretty much told me what to look for to get the drum out. Followed the instructions sent with the bearing kit and removed the old bearing assembly. Ran the screws supplied with the kit into the bearing assembly before I installed it. This was a tip I got off PartsSelect website. Runnin ... Read more g the screws in first is a must! Had my wife hold the assembly in place while I ran the screws in. That part of the job is the only time you need an extra set of hands. Put the dryer back together and it works like a quiet champ now.

I love the Partsselect.com youtube videos. The man in those videos rocks!!! I did the repair of my rear drum bearing kit exactly as he showed me in his video and it was perfect. I have spread the word on facebook and around work about Partselect.com and friends and coworkers are already checking it out. Hey, everyone loves a good thing. I ... Read more suggest that you do not be afraid, you CAN do it. Tear that baby apart and save yourself some money.

Actually, my boyfriend did the repair by taking off the top and back of the dryer to access the drum and belt he replaced the belt and put the dryer back together
We are greatful for your service and really happy we didn't have to drive all over to find the part.

Your instructions were execellent
Problem is solve
Thank you

replaced rear drum bearing kit Still makes the same noise

I was teaching my associate how to do this repair so I showed him how to take off the top of the dryer. Then I showed him how to replace the drum slides. I had him clean out the dryer since we had it apart, and I also showed him how to remove the drum and then reinstall it. This was a very easy repair, and he learned a lot that he otherwi ... Read more se would not have known. Thanks for getting the parts to me so quickly. Rob from Clarks Summit.

First I removed the drum as described in many other comments. Took me about 10 minutes, pretty easy. Replaced the part which was easy and could be figured out just by seeing how you took the original part off. The hard part was aligning the drum, drum washer, and metal plate back into the drum bearing. I tried over 2 hours to do this ... Read more and because it rotates and it's almost impossible to line up all the holes, I decided to do it another way.

I took apart the drum bearing from the back panel and then outside of the dryer walls I aligned the drum, washer, metal plate and drum bearing. I screwed them all in together and then, went into the frame and reconnected it at the back w/ the horseshoe looking washer. It worked perfectly and I was frustrated that it took me so long to figure out a different way to do it.

I have to say because of the installation it was a little tough than anticipated but was very happy with the end result (no squeaking) and money savings. Definitely worth giving it a try if you're patient.

Removed the top, front and lower rear section of the dryer. This being my first experience replacing a dryer belt I naturally missed the tensioner pulley first try, then installed the belt on the wrong side of the pulley and found I didn't have enough tension. After some thought and a long hard look I realized my mistake and the third tim ... Read more e was the charm. Next time I need to replace a dryer belt it should be a snap and go a lot faster.