CED7006GW0 Crosley Dryer - Instructions

To reach the heating element you only need to open the back cover of the dryer (about 8 nut-head screws). Remember to disconnect the power.

To remove the heating element there are two small nut-head screws. Remove the two electric wires. Then you can pull the heating element away.

You can check the heating element wi ... Read more th an ohm-meter or visually inspect it to see if the heating element spiral wire is broken.

Don't hurry to dispose the old element. My model includes a small electric safety part. You'll need to transfer it to the new heating element (that comes without it)..

Good luck.

i was able to go on line with your company , find my dryer, order the part and had it the next day. fast , great , service

The repair was easy. the most time consuming part was vacuuming the dust from the back of the Dryer, The repair required removing screw from the back panel of the dryer. Then removing screws from the heating element and unplugging the wires. The only moderately diffculy part was swapping the sensor form the old element.

Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source.

Pryed dryer top open and opened front door. . Unscrewed the 2 retaining screws. Pulled old switch from the wiring harness. Put new switch in place and replaced the retaining screws. Put new switch wire plug into the wiring harness. Before closing top, checked door switch function with dryer on. Dryer cut off when door open an ... Read more d when closed dryer started normally. . . Maint. Note instruction book should warn that letting door slam, which I did on occaision, broke the switch arm. Might save future problems.

Moved dryer from wall,disconnected power. Unscrewed the 12+ sheet metal screws holding on the back cover. Located heating element, remover it's two sheet metal screws and pulled down on the element to remove. Disconnected the two electrical leads from element and went to the top of Dryer. Do not remiember if told to remove the temptur ... Read more e kill button was easy to see that it was needed on new element. Moved high tempeture senson to new element. Reversed steps to install new element. Replaced back cover, pluged in and powered up. Works like a champ. Thanks for the price on the part and the video which started me on the right track. I'll be back !!

Removed some screws and partially dismantled the door so I could get the old catch out. Inserted the new catch, and put the screws back in. Saved me an $80+ service call.
On the filter, I had to use pliers to remove the old one because the handle had broken off. Did that, and inserted the new one. Done. Sears had been unable to supp ... Read more ly me with a new filter.

It was simple once I figured out what to do:). I removed the 2 screws on the top of the dryer... they were a bit hard to find. Even with the other descriptions on this site. I was removing things I didn't need to. The 2 screws you need to remove are under the LINT COLLECTOR LID. Remove those 2 screws & lift the lid... it will be tigh ... Read more t at first. the front of the lid has 2 "catches" in the corners.

The hardest part was getting the door switch assembly to "unplug". We pried it off -- eventually -- & then simply plugged in the new one.

Saved me LOTS of money & was worth the 30 minutes - 1 hour of work.

As I said previously, once you realize how to get the lid up & manage to pry off the plug, that's all there is to it -- easy!

Save yourself time & money & do it yourself!

I first disconnected the power. Then, I took off the back panel with about 8-10 screws. There were a couple of screws that held the heating element in place, which I removed. Then, I disconnected the heating element. The heating element was toward the bottom right hand side and was easily accessible. The connections to the heating element ... Read more were a little bit tough to disconnect but not too bad. I had to use a flat head screw driver to kind of pry them off but looking back I think some needlenose pliers would have worked better. I then removed the bad heating element and plugged in the new one. I replaced all the screws and turned the dryer back on. It blew hot air again and all was well. I am not very mechanical and it was all pretty easy.

Grow a second set of hands. Always unplug any appliance. Remove lint screen. remove two screws (philips Head). I took a wooden shim lightly tapped w/hammer to pop front of dryer top free. Mine worked on hinges and just flipped back til it rested against the wall. Removed two 5/16 screws inside holding face on carefully raise face section ... Read more off the support clips at either side on the bottom. Pull drum out (I have the large style drum commercial size [approx.). Clean the inside free of all lint (known to be fire hazard). Sling new belt around drum. Get newly grown set of hands to hold drum in place. Pinch belt to fit between tensioner, lift tensioner and place belt around motor pulley. Spin drum couple times to make certain belt isn't twisted. Reverse dismantle proccess to put back together. Replace all parts that come with kit, you'll feel better knowing you got a new dryer, almost.

First I called an appliance repair place. They charged me $40 to come out and said "the air vent might be clogged". I snaked it out and really wasn't anything in there. So I started thinking it might be a thermostat. After reading the reviews that others posted here, I said, "how hard can it be"? Thanks to PartsSelect putting a diagra ... Read more m (schematic) of the parts, I could see what I was looking for when I removed the back panel. So I took my nutdrivers out, disconnected the vent hose and removed the 10 or so nuts off the back panel & got it out of the way. Took out the vacuum cleaner and sucked all the lint out. Removed the housing where the heating element was and marked on both thermostats and housing where each wires went. As cheap as PartsSelect had the thermostats priced, I figured why not remove the guesswork by buying the highlimit and cycling thermostats and a new heating element too. One screw in each thermostat and out they came. Swapped wires with new thermostats and put them back. With the heating element...it was all one piece, so no fighting to get the element into an old housing. Just swapped them. Put the back panel on and reconnected the vent hose. Cost to repair: about $100. Time for parts to get to me: 2 days. Time to install new parts: about 10 minutes. Knowing that I have a dryer that runs like new AND saving a TON of money on electric bill....THAT is priceless. Thanks PartsSelect!

I can't believe I waited so long to find this part and do this. I got the package very fast, opened it, took the piece to my dryer and popped it into place with my fingers. It worked perfectly! this took all of two minutes and saved me from having to hold the dryer door closed with a stick. Thank you, thank you!!!

After realizing that my dryer was no longer heating, I took off the back and examined the heating element. I saw that a coil was broken and knew that it needed replaced. When the part came in, I basically changed out the wires that were plugged into the old element on to the new one, replaced the screws in the heating element housing an ... Read more d back panel, plugged in the dryer and was back in business! Oh, by the way...I am a 49 year old WOMAN!!!!

First unplug your dryer. Then, I removed the two screws on the lint trap leaving the lint trap in place--do not pull out the lint trap--only remove the two screws. Next, slide the top of the dryer slightly forward in order to release the top of the dryer. I did this with my hands. Once the top of the dryer is released, raise the top of t ... Read more he dryer and unplug the door switch assembly. Then, remove the two screws that hold the switch. These two screws were located on the front panel of my dryer and are visible when you open the dryer door. Remove the old switch and install the new switch by putting the two screws you previously took out from the old switch back in place and plug in the new switch. Lower the dryer top. Push the top back to lock in place. Line up the lint trap holes for the two screws that hold it in place and replace those screws. Plug your dryer back in and it should work properly. Very easy repair. We ordered our part one morning before noon, and it was here the next afternoon with regular shipping. GREAT SERVICE.

This repair was a cinch. Pliers to pull out the metal piece and a screwdriver to pry out the 'catch' part in the door. Both replacement pieces went right in. I cannot believe how easy and CHEAP this fix was, and I'm so glad I found this site!! I figured I would have to call a repairman and pay big bucks, so I put it off, but the door ... Read more was getting worse--slamming it so hard to keep it shut. Again, thanks for this great site.