CDW9380N00SS General Electric Dishwasher - Instructions

The dishwasher was disconnected and pulled out. I turned it over onto it's side so I could get down to the drain pump. It looked exactly like the original part and fit just as well. The hoses came right off and then once it was replaced, slipped right back on. It all worked like a charm. The only problem I had was after the repair. T ... Read more he copper water line moved around too much and caused a leak at the connection at the dishwasher. Luckily I tested the line outside before I reinstalled it completely. I just went and bought an $11 flexible hose with new fittings on either end and replaced the copper lines. It went on easier and it sealed tight.

This was a pretty easy repair and I am glad I did it. We were on the verge of just buying a new one, but for a $35 part and a couple hours, it was well worth it.

First I had to unscrew screws under the counter then pulled built in dishwasher out from under the counter, attached hing arm link to right side bracket on door, and the other end I attatched to a spring at the back of the unit. Thats it! and pushed the dishwasher back into place. All back to normal....by the way Im a 67 yr old great gra ... Read more ndmother...

I took out the old rack and put in the new rack. Took about 20 seconds tops. But I had thought I needed to order the wheels (8 of them) and the wheel attachments (8 of those, too) separately because when you go to order the rack, it is suggested that you buy those, too. But the rack came with all the parts I needed so I ended up returnin ... Read more g the stud rollers. Very happy with the product and the friendly service.

Turned power off, removed dishwasher, tipped on side, removed and installed pump asym, reinstalled

replaced it

The repair was very easy, I just had to replace some bad bearing slides in the drawer pull. Remove the end cap, remove the top drawer, remove the old bearing slide from the drawer slide and snap the new one in. finally replacing the end caps.
Ordering the parts was easy and delivery was fast.

Removed Dishwasher, inverted it and replaced the sump housing. There are 2 screws mounting the top of the dishwasher to the counter, a water connection and the electrical connection. Remember to turn the water off and the electricity off. Slide the DW out on carpet. Carried it to the garage to affect the repair. Reinstalled the dishw ... Read more asher. Most difficult part of this is that the water hose is really short. I used a 6ft extension so that the next time I have to pull this out it will be easier.

This was a piece of cake. The original soap dispenser never worked right and always left unused soap. The new part was easy to install and works great. Only needed a 1/4" nut driver and philips screw driver to pull the outside panel and replace the module rinse and cap assy. Easy!

Turned spray arm while lifting upward to remove the old part. Place new spray arm over the water outlet and turned with light downward pressure until properly seated.

It less time to do the repair than it took to open the box and unwrap the part!

Exactly as described by a previous reviewer. I pulled out the old rack, put in the new rack and just moved over the cutlery rack.

Hint on determining if the Main Conduit is the cause. Place a tapered flat piece of wood (wooden spatula) between the Main Conduit and rear of the dishwasher wall and remove any excess play.
Run the wash cycle and determine if the noise goes away or is reduced.

Removal and Replacement of the Main Conduit Assembly:
O ... Read more pened the Dishwasher door and removed the lower and upper basket.
The upper basket required the two rubber gourmets on the front of the rail to be removed by inserting a flat bladed screwdriver between the top of white farthest tab towards the rear of the dishwasher of the rack slide end cap (PS2370502 – Item 652) and twist the screwdriver while gently pushing the top of the tab towards the rear of the dishwasher and gently pulling on the end cap (The rear tab needs to clear the upper rack slide).
Repeat this process on the other upper rack slide and remove the upper rack assembly.

Using a ¼ inch socket driver, remove the Main Conduit (PS651676 Item 585) screw located in the back of the Dishwasher wall and the screw from the upper spray arm (PS260547 Item 570) located on the roof of the unit.
Remover the lower Spray arm by gently pulling up and turning it counter clockwise.
Remove the fine filter hub nut (PS259078 item 454 ) by turning it counter clockwise and the fine filter (PS259068 item 452) The fine filter has a small tube going into the bottom of the dishwasher base that should be removed at the same time of the filter. Be sure to position it correctly when it is reassembled.
There is also a small stainless washer in the bottom of the fine filter housing. Take care not to loose it during the assembly and disassebly process

Remove the Main Conduit from the plastic assembly in the drain of the dishwasher by turning it counter clockwise. (Note, the new Main Conduit Assembly comes with this part pre assembled). Remove the same plastic piece from the new Main Conduit assembly by carefully lifting the clip on it.
Install the new piece back in the drain and tighten just prior to being pointed toward the back of the dishwasher.
Reassemble the Main Conduit to the drain piece and tighten it the remainder of the way and reassemble all parts in the reverse order they were removed.

Opened the package. Set screw fell on floor. Luckily cat found it right away. Fight the cat for the screw. Dug through my tools and the first Allen wrench I picked up fit. "What the hell? That never happens so obviously the screw won't fit," I think to myself. Put the screw in the hole and give it a few turns until my fat finger can't hol ... Read more d it. It's a miracle and the thing fits! Fight the close quarters with the Allen wrench to tighten it. Works like a charm!! Now I don't scare myself when I open the door thinking I'm going to rip the handle right off. Now I have easy access to my ice cream. The parts finder tool on the website was really easy and I found what I was looking for.

Part was an exact match. Make sure to use plumber's tape on all threads. Had to really tighten fittings to prevent leaks. Screws are a little difficult to get to. Test for leaks first, before final installation.

1. remove old basket. 2 Place new basket.. Done

Once we ordered both the "Stud Roller" and "Roller Lower Rack" the repair was simple.

The previous studs mostly disitegrated, so their removal was not an issue. The wheels pulled off easily.

I recomend getting new studs and rollers for all of the wheels on your rack. For me, that was 8 wheels and 8 studs.
... Read more r />First, take the rack out and flp it upside down in a convenient working space. Next, remove all of the old wheels and studs from the rack and discard. Then, snap the new wheels on to the new studs. Next, atached the stud (with the wheel) to each of the 8 spots on the rack. Put the rack back in the dishwasher and walla!

I can't beive that I waited almost two years to make this simple repair.

Read less