CDT725SSF0SS General Electric Dishwasher - Instructions

Removed the screen cover and then removed two bolts with nut driver and removed white plastic retaining piece. Pulled flood switch out of housing (raise approximately 2 inches) then unfasten electrical plug. New part connects to electrical plug (pnly can fit one way so no problem with orientation). Pushed floid switch bsck into lace and a ... Read more ttached white plastic retainer with two bolts and then set screen cover back. Very simple and easy.

Replaced heating element. This was the path of least resistance but the problem persisted. I tried resetting the dishwasher but still nothing. My last resort is the circuit board. I checked the relays on the old board and they are fine so it must be something else on the circuit board. The dishwasher is not really that old (4 years) ... Read more and everything else is fine. Just ordered the board so I really hope this fixes the problem.

First went to U Tube to view installation instructions and location of part. It was fairly easy to replace since I had installed the unit. I was able to move the unit out enough without disconnecting any line since there was enough slack in all three connections, only shut the power off. I did use the new parts even though the older ones ... Read more were not broken. The nylon pulley wheel had built up with lint causing the cable to come off.

I have them to the plumber who was reinstalling a poorly installed dishwasher. Parts worked perfectly

The service lady looked up possible trouble items and narrowed it down to the flood switch. Being the most likely cause, I ordered a new one. I removed both trays, the lower sprayer, and both screens. The flood switch has an electric plug on the bottom of it that just pulls off. Just as with other appliance repairs, I actually got the ol ... Read more d flood switch to work again before trying the new one. I should have tried to free up the float before ordering the new one. But in case this happens again, I’ll just put the new one in.

Turned off pier at breaker. Removed dishwasher from under counter after disconnecting water line from dishwasher and drain tube from under sink. You might get a little residual water but not much. Removed old flood switch took about 2 minutes. Replaced with new flood switch. Then tilted dishwasher back to get to plastic nuts that hold dow ... Read more n heating element. Set unit back down and removed old heating element then replace it with new one. Replace plastic nuts that hold element. Exact parts makes job easy. Them put water hose back on an put washer back in place hooked drain hose back up. Turned water and power back on. Tested unit worked perfectly. Hardest part of job was putting the dishwasher back into counter and getting the Instalation back on top.
Parts replacement time was about 10 minutes.
Disconnecting and reconnecting and replacing dishwasher 40 minutes. But I wouldn’t pay anyone to do this because it’s really not difficult.

I did not do repair. I originally tried to order part from GE. They informed me I had to buy the whole door to replace the bottom door seal. I then looked at Part Select and they had the exact schematic as GE except showed the seal. I called and sales person assured me it was the part I was looking for. My dishwasher. What they didn’t te ... Read more ll me was that seal is riveted to the door. I ended up throwing away the part as it was more expensive to return it . SonPart was a total waste..

So after noticing some horrid food waste build up in my 9 year old dishwasher, I determined it wasn't heating the water during the wash cycle. I came on here to check how to replace the heating element and was surprised when the flood switch was instead strongly recommended as the first repair step.

I ordered the part, and prep ... Read more ped the dishwasher for the repair (Pro-tip: Clothes pin attached to the bottom of the flood switch wiring harness ensures it doesn't slip down below the opening during the part swap!). The part swap and reassembly only took 5-10 mins or so after prep and dishwasher is now heating water and running great again. Many thanks to partselect.com for the detailed installation guides/videos and the parts recommendations!

Had to remove the rubber gasket on the new spray arm to install the device, as it was hard to push into the above slot that fits the arm..

It was relatively easy to fix. I unscrewed the mounting screws from the cabinet, slide the dishwasher out to access the pump under the dishwasher, I did raise the dishwasher on the left side and steadied with a stool to make access to the pump fitting easier. Then I loosed both clamps at the ends of the hose ie. from the dishwasher pum ... Read more p and the connection to the sink drain line, pulled the clamp off of the end that connects to the pump and placed it on the new hose connection, I removed the old hose, connected the new one and tightened the drain line connections. I placed the hose in the hose holders on the side of the dishwasher slid the dishwasher back into place and secured it in place with the mounting screws.

Water valve replacement was easy. Turned off water supply valve. Unscrewed water supply from valve on dishwasher, removed 2 water hoses , that feed top and bottom sprayer’s And reinstalled everything opposite of removal. 5min job

Simply pick the basket up to slide wheels onto axles and push in until they lock in place.

Unscrew the upper and side holding screws. Move dishwasher part way out. I didn't need to disconnect the water or electric. Make sure the electricity is off. Remember your working around water. Take off the bottom plat removing two screws, Remove broken cable pulley and replace new. Buy two since your their you might want to replace ... Read more both. Have fun! It's duck soup.

Simply twist on the new part/filter.

Popped old bracket off with screwdriver, with a then easy installation of the new part.