- Home
- BTF2140FS0
- Instructions
BTF2140FS0 Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Kenmore 417.41042000 Front loading washer shakes
8 of 10 people
found this instruction helpful.
-
Chris from Burtonsville, MD
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers
Paid $27 total for a shock kit to replace the 2 broken stock shocks. Replaced them. It turns out it was not the problem, but just a symptom of the spider bracket (mates inner SS drum to drive shaft) corroding and breaking causing the drum assembly to shake out of balance. Found out is a systematic problem with this model washer, and no ma
... Read more
tter what else you fix, this will break and kill it at some point. Piece of crap!
Read less
Was this helpful?
Thank you for voting!
washer door handle broke
7 of 8 people
found this instruction helpful.
-
mandy from rock falls, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
unscrewed the old handle, and screwed the new one on. It only took 2 minutes to fix. Very easy!!
Was this helpful?
Thank you for voting!
tab broke off when the door was shut too hard.
9 of 14 people
found this instruction helpful.
-
scott from albertville, MN
- Really Easy
- Less than 15 mins
-
Screw drivers
2 screws and about 48 seconds of work. very easy.
Was this helpful?
Thank you for voting!
Door handle broke off at the top
7 of 9 people
found this instruction helpful.
-
Mary from Oswego, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
Like another commenter, my teenage daughter ripped the handle off at the top in a huff. My husband simply unscrewed the broken handle and replaced it with the new one. We now make sure to open the door from the middle of the handle, not the top.
Was this helpful?
Thank you for voting!
door slammed shut
7 of 9 people
found this instruction helpful.
-
May from Abilene, KS
- Really Easy
- Less than 15 mins
-
Screw drivers
door not level son slammed shut and door strike broke
Was this helpful?
Thank you for voting!
No spin
6 of 6 people
found this instruction helpful.
-
Matt from MAPLE SHADE, NJ
- Easy
- 15 - 30 mins
-
Nutdriver
No spin, water+drain worked playing with settings. Dart 1-door switch. Got code-tested motor-ok. Replaced motor control board
Was this helpful?
Thank you for voting!
Washer would not spin or complete spin cycle
6 of 7 people
found this instruction helpful.
-
Jonathan from Littleton, CO
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
E47 error code means control board or door lock. From reading other stories, I decided to try the door lock first since it is much cheaper. Frigidaire tech support was no help at all.
First I removed the "wire" and spring that hold in the rubber seal at the door.
Then I removed the 2 screws that hold the door loc ... Read more k in place.
Removed the door lock, unplugged the 3 connections, plugged the connections into the new door lock, screwed it back in and replaced the rubber seal and wire that holds it in place.
Runs fine now.
First I removed the "wire" and spring that hold in the rubber seal at the door.
Then I removed the 2 screws that hold the door loc ... Read more k in place.
Removed the door lock, unplugged the 3 connections, plugged the connections into the new door lock, screwed it back in and replaced the rubber seal and wire that holds it in place.
Runs fine now.
Read less
Was this helpful?
Thank you for voting!
The door handle to the front load washer had broken off
7 of 10 people
found this instruction helpful.
-
Francine from Wolcott, VT
- Really Easy
- Less than 15 mins
-
Screw drivers
Very easy. Remove 2 screws from the inside of the door. Take out the broken pieces and screw in the new one using the old screws.
Was this helpful?
Thank you for voting!
Broken front on dispenser drawer
5 of 5 people
found this instruction helpful.
-
Helen from AURORA, CO
- Very Easy
- Less than 15 mins
Despite putting all the information about my washer in the order, I received a dispenser drawer that was similar to the one I needed, but would not fit. It was also a slightly different color than the original part on my machine, so obviously someone just threw it in a box and sent it to me. It wasn’t even wrapped in plastic! Just the
... Read more
part in a box, no instructions, no bill of sale, nothing. When I needed to return it because it wasn’t the proper part, I HAD TO PAY THE $10.00 TO SHIP IT BACK!!! Really poor customer service in my opinion. Hopefully I will at least get a credit for the incorrect part that I had to pay to return.
Read less
Was this helpful?
Thank you for voting!
The front level screw legs are made of plastic and each time I move they break
5 of 5 people
found this instruction helpful.
-
Bobby from Asheboro, NC
- Really Easy
- 15 - 30 mins
-
Wrench (Adjustable)
screwed in the new legs and leveled it off again.
Was this helpful?
Thank you for voting!
Loud humming noise from the door closure area.
6 of 8 people
found this instruction helpful.
-
Alyre from Van Buren, ME
- Really Easy
- Less than 15 mins
-
Screw drivers
First,turned the power and water off. I disassembled the door lock and switch assembly by removing two screws from the rear of the top lid to gain access to the switch. Removed two screws from the switch assembly located in the front door latch area. With screws removed, I seperated the three terminal blocks and inspected the assembly for
... Read more
failure potential. Discovered a small crack in the switch housing which created error in relay function. Ordered the part and installed in reverse order of above. Realigned the door for proper closing, turned water and power on and did laundry all night to catch up!!!
Read less
Was this helpful?
Thank you for voting!
One of the wash tub shock absorbers broke.
6 of 8 people
found this instruction helpful.
-
Joshuah from Indianapolis, IN
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I heard that the repair job was simple and the part was not expensive (whew!) The repair video on your website was MOST helpful and gave me confidence. At first I tried it exactly as the guy demonstrated and all went well removing the broken support. Installing the new one (on the right side) was impossible for me. I could not get good
... Read more
enough leverage to fully re-insert the lock pins and I was slicing up my arm on the sharp metal edges. I removed the 900+ screws (just kidding- but there were quite a few) from the back panel and could access the lock pins MUCH easier. All four for both shock absorbers snapped right in. Re-attaching the rubber vent hose involved a few cuss words but I got it back on correctly after taking a break. All is great with the little washing machine once again! Thank you for the installation video and amazingly fast shipping, wow.
Read less
Was this helpful?
Thank you for voting!
belt was still on washer, had developed a loose tear
7 of 11 people
found this instruction helpful.
-
jeffrey from mount juliet, TN
- Really Easy
- 15 - 30 mins
-
Screw drivers
Very easy to replace belt on this model, belt had spilt and the loose rubber was flopping around and dislodged plug from water pump. Washer would not start cycle, display showed (no spin). Removed back access panel with screwdriver. Spin the pulley and slip belt off pulleys. New belt is very tight but it will go on, no tension adjustme
... Read more
nt on this model. Thanks part select quick service will order again from this company.
Read less
Was this helpful?
Thank you for voting!
Washer Door Wouldn't Lock
6 of 9 people
found this instruction helpful.
-
Shawn from Springdale, AR
- Easy
- 15 - 30 mins
I watched the u-tube video and followed what he did and it was fixed. Reason it took over 15 min I had to find the correct bit for the screw. I think your web site is great thanks
Was this helpful?
Thank you for voting!
Washer wouldn't enter the spin cycle. Clothes wet at end of wash cycle.
5 of 6 people
found this instruction helpful.
-
Leslie from Tolland, CT
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Open the door. Pull the clamp off of the boot (locate spring at bottom). Peel back the boot on the right side so that you can get to the door lock and switch assy. Remove the 2 screws in the front that hold in the door lock and switch assy. Remove the wires from the old assy. Transfer the wires to the new assy. Screw in the new assy
... Read more
. Refit the boot and clamp. give it a try.
Read less
Was this helpful?
Thank you for voting!