EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

BL02B Magic Chef Refrigerator - Instructions

All Instructions for the BL02B
121 - 135 of 625

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replaced Ice Maker
2 of 3 people found this instruction helpful.
  • Steven from Clinton Corners, NY
  • Easy
  • Less than 15 mins
  • Nutdriver
Followed the online PartSelect video instructions and it was very helpful. The ice maker has to cycle through before it starts making ice so don't be alarmed when nothing happens when you first hook it up.
Was this helpful?
Thank you for voting!
Ice Maker Leaked Creating an Ice block
2 of 3 people found this instruction helpful.
  • Loren from Indianapolis, IN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Merely remove the front bottom screw that attached the ice maker to the refrigerator
Lift the ice maker gently off of the 2 top screws
Unplug the icemaker wiring harness from the back of the refrigerator, and remove
Snap off the end of the maker and remove the keeper for the wire arm
Remove the wire arm and install on new maker
Unplug the wiring harness from the old maker and plug into the new one
Plug the harness into the refrigerator, slip the new maker over the top screws, with the water feed tube inserted into the maker
Install bottom screw into the bracket that holds it in place.
This took less than 5 minutes.
Was this helpful?
Thank you for voting!
Replaced leaking ice maker after minor screwup!
2 of 3 people found this instruction helpful.
  • Jackson from Leesburg, VA
  • Easy
  • 15 - 30 mins
  • Nutdriver
Old ice maker leaking water and produced ice cubes with black inclusions. First, I removed old ice maker per video instructions. Transferred electrical cable, cover, and bail to new ice maker. First installation failed because I failed to make sure water tube correctly enter back of ice maker. No ice. Initially thought electrical cab le wasn't firmly in place. Then I noticed frozen water dripping down back of freezer. A clue! Removed ice maker and reinstalled making sure water tube went through the hole in back of ice maker. Now the new ice maker works beautifully!
Was this helpful?
Thank you for voting!
ice maker quit working
2 of 3 people found this instruction helpful.
  • Randy from Yale, OK
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Replaced the water valve. I knew that the ice maker was working by watching the movement. It was not getting water to it, s I figured it was the electric water valve and sure enough, that fixed the problem.
Was this helpful?
Thank you for voting!
Quit making ice
2 of 3 people found this instruction helpful.
  • James from Charleston, SC
  • Easy
  • 15 - 30 mins
  • Screw drivers
Loosen the screws on the sidewall (don't take them all the way out and drop them on the floor as I did) and remove the screw from the bottom bracket. Change out the electrical wires and the wire level sensor that does not come with the new unit. Put the new one in place and give it some time to cool down and make ice ( don't be impatient like I was and think the new unit was bad or that you replaced the wrong part)
Was this helpful?
Thank you for voting!
refrigerator was overheating, condensor fan dead.
2 of 3 people found this instruction helpful.
  • David from Granada Hills, CA
  • Really Easy
  • 15 - 30 mins
First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade ,
reinstalled cover, plugged it in and BAM .WORKS PERF!
Was this helpful?
Thank you for voting!
Replaced refrigerator light assbly
2 of 3 people found this instruction helpful.
  • Charles from Stone Mountain, GA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
replacement was relative easy. The problem came with wire connector that had to be cut, stripped and crimped. The crimping was the dificult part. the connector was a problem to crimp.
Was this helpful?
Thank you for voting!
Outer case of freezer was heating up, not making ice (sometimes) turned up thermostat several times (especially freezer)
3 of 6 people found this instruction helpful.
  • John from Greensboro, NC
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver
I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.

Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well
Was this helpful?
Thank you for voting!
difficulty unplugging the power pigtail
2 of 3 people found this instruction helpful.
  • William from Las Cruces, NM
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Just kept working on it.
Was this helpful?
Thank you for voting!
Old Valve was dead
2 of 3 people found this instruction helpful.
  • Joseph from Bloomfield Hills, MI
  • Really Easy
  • 15 - 30 mins
  • Pliers
This was very easy and pretty fast to do and its working great...all for $40 bucks ! you can do this...trust me!
Was this helpful?
Thank you for voting!
noisy fridge, perimeter of door heating up
2 of 3 people found this instruction helpful.
  • craig from maple grove, MN
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
figured out the condenser fan was kaput. Tried WD, worked for several days then gave out completely. Took off back of fridge and trained small fan on compressor while I ordered new condenser fan. The swap was easy, undid the housing bolts, stripped off the connector, reconnected and voila! works perfect.
Was this helpful?
Thank you for voting!
icicles from pooled water in ice collector bucket
1 person found this instruction helpful.
  • Roberta A from WINTER HAVEN, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
I watched the repair video on the web site a couple of times just to get comfortable with what to expect. (i.e. pressing tabs on wiring harness to remove, placement of lift arm for removal and installation) These instructions were a big help...I had the removal, modifications and installation completed in less than 30 minutes. Ice cube s (without the extra icicles) in 1 hour...
Was this helpful?
Thank you for voting!
Ice maker broken. Quick fix
1 person found this instruction helpful.
  • Tim from Berkeley, CA
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
The plastic fill cup part is also used to hold one end of the wire “one/off” switch that is manually activated or activated when the ice tray is full. This wire piece fell out because one end, that is part of the plastic fill cup, broke off. The wire switch was fine.

The video demos show you exactly what to do. The repair man showed me a trick to speed up the testing process. The trick is to insert a wire jumper cable to actuate the ice maker and make it rotate. But this isn’t necessary.

Hardest part of this fix is emptying the freezer (bottom with a slide out door) and removing the door.

Why this part is so expensive is beyond me. But I’m happy it was available for a 24yo fridge that still works!!
Was this helpful?
Thank you for voting!
original motor stopped
2 of 4 people found this instruction helpful.
  • Paul from Lowell, MI
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Socket set
removed old and instaslled new. biggest problem was getting to one of the screws.
Was this helpful?
Thank you for voting!
Ice Maker leaking.
1 person found this instruction helpful.
  • Jeannine from Pontiac, IL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
I watched the video regarding the instillation of this ice maker a few times and then followed it exactly. It was incredibly easy. We had ice cubes about two hours later and no longer had a leak making icebergs!
Was this helpful?
Thank you for voting!
All Instructions for the BL02B
121 - 135 of 625