AS27 - Instructions

I Removed the two wires from the old relay. I Then pulled the old relay off the compressor. Next, I had to get the overload seperated from the old burnt relay, which took some care not to break. The old relay and overload is in a plastic compartment. Then I followed the directions that came with the new relay. The only confusion came with ... Read more getting the two wires back onto the terminals of the new relay, mainly because the old relay was burnt so badly I didn't have any idea how it was originally wired. I crossed the two wires on the terminals of the relay. The compressor would click off and on, but would not start blowing cold air. I swapped the wires on the terminals and it started working immediately.

Step 1 :I had to remove the ice drip tray just pull it out.
Step 2 remove the 4 or 5 screws holidung in the control module (push button display pad)
step 3: pull the plug from the diaplay panel
Step 4: remove broken door from slot and slide new one in. Be carfull not to let the brass plug fall out of it does it just slides ... Read more back in.
Reverse all steps your done about 20- minutes..I am a building engineer by trade. I think the average person 30 to 60 minutes..

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

followed the instructions provided and that's it!

Just pulled out ice bucket put to the side and then pulled out framed housing that surrounds the ice bucket tray and put on table
went in the rear where the turn motor is and disconnected the wires from the housing next to it and disconnected the motor which had cracked the wal it was mounted to and broke and fell which left a hug ... Read more e hole and the , took the 4 screws out and remounted it onto the new housing rear wall, note that to get the twist key lever that unscrews clock wise you may have to hit wit a hammer bluntly to brak it lose first then it unscrews easy, but this has to be done first before re assembly of the motor as it goes through the new housing wall , once this is donr then put your screw end through the hole and re assemble the wing devise back onto the moter screw drive which it will screw on counter clockwise and tap a few quick times to snug with a ball hamer or a small hammer, T
The hinge door pin is real easy, just unscrew the top of door 3 screwa and lift off the door set aside put new door pin hinge on then set the door back onto the pin hole align up and set it back down in the hinge hole and replace screws on the upper door hinge on top of fridge. all this took about 5 minutes tops, it took me more time to take all the items out of the doorway of my fridge that it did to do the task itself. Hope this could help.

removed the ice chute door, unhooked the computer board replaced the flap. The only problem was the spring loaded part of the ice chute door come up and the little plunger came loose. It only took a few minutes to replace the plunger back in the holder and replaced the ice chute door. The best part of the whole job was that I ordered ... Read more the part on Monday afternoon and the part was at my door Wednesday. The Parts did an excellent job of getting the part to me quickly.

Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiv ... Read more er boaed. I turn off manually the icemaker, when needed

Had to disassemble ice maker to install part. . .

Part selects cataglog for parts selection was very easy to use and the online service and delivery was great.
When I got the part, it was not apparent on how to remove the auger so that I could insert the new connector. There were about about 8 visible screws, with star drive heads that I fortunately had a screwdriver that fit, and ... Read more I could not tell if I had to remove all of them or only a couple.
I ended up removing all, but still could not separate the dispenser portion which held the front of the auger from the back of the ice bin. I finally figured out that the dispenser door trip lever had to be disconnected and I almost lost it when I removed the metal clip that attached it to the outside of the ice bin when the spring loaded lever tried to unwind. I managed to hold it in place, separate the dispenser holding the auger from the rest of the ice bin and replace the connector. I them got the pieces back in place and was able to refasten the spring loaded lever and then replace the screws.
If the spring loaded lever had unloaded, it would have been tricky to try to replicate the amount of turns (load) on the spring tension.

I removed the water filter located in the refrigerator and replaced it with the bypass plug. The ice cubes and the water dispenser work properly . I am pleased with the outcome especially the price was only $15 and less than 5 minutes of my time. Maytag recommends replacing the water filter every six months at $40 a filter. One can see ... Read more how this will add up in time. Eventually I am installing an after market water filter in line prior to the refrigerator.

It was easy breezy!! I felt like an empowered woman that I did it myself. I simply removed the old shelf supports with a screwdrive and inserted a screw thru the new supports and screwed them in.

We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.

1/4 turn of old filter. it popped out. Inserted new filter, 1/4 turn and it clicked in. Piece of cake. I'm a freakin' genius.

Unscrewed old filter and screwed in new filter.

googled for answer, deduced relay/switch problem. googled again for parts, found partselect.com, ordered part. 2 days later & $70 lighter, my 8yr old Maytag was working again! Parts were good fit, instructions were decent enough. Not for inexperienced tinkerer though.