My Orders
- Home
- ART308FFDM07
- Instructions
ART308FFDM07 Whirlpool Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Plugged it in.
1 person
found this instruction helpful.
-
Adam from GLOVERSVILLE, NY
- Really Easy
- Less than 15 mins
-
Nutdriver
Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.
Was this helpful?
Thank you for voting!
Fan was not spinning make it not cold in bottom part
1 person
found this instruction helpful.
-
Dylan from WHEELING, WV
- Very Easy
- Less than 15 mins
-
Screw drivers
Take screws out pull panel out unconnect the part connect new one and your done
Was this helpful?
Thank you for voting!
GASKET AROUND DOOR WAS LETTING AIR IN/ COLD AIR OUT
1 person
found this instruction helpful.
-
Susan from BONNEAU, SC
- Very Easy
- Less than 15 mins
Put gaskets in the car dash to get warm (90 outside), Pulled off old gasket and brought new one in and just inserted it into the slot around door. Was a little buckled but it straightened out after a few hours. Was very easy!
Was this helpful?
Thank you for voting!
door hinge broke.
2 of 4 people
found this instruction helpful.
-
Bernard from DONALDSONVLLE, LA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed door and replaced bushing bracket was ok.
Was this helpful?
Thank you for voting!
compressor not running
1 person
found this instruction helpful.
-
Doug from Lancaster, CA
- Really Easy
- 15 - 30 mins
Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now
Was this helpful?
Thank you for voting!
Very easy installation
1 person
found this instruction helpful.
-
David from Woodstock, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers
The cover just popped in, no problem
Other Parts Used:
Was this helpful?
Thank you for voting!
Warm fridge and freezer but compressor was running. No air distribution inside fridge
1 person
found this instruction helpful.
-
Brian from BURTON, MI
- Really Easy
- 15 - 30 mins
-
Nutdriver
I turned breaker off to fridge, it was easier than pulling fridge out in camper. I took 4 screws out of back panel that revealed the evap fan, took 2 more screws out to take fan bracket off. Unplugged fan plug. Took fan blade off the non working evap motor and put it on the new evap motor. Put all the screws back in the reverse orde
... Read more
r and flipped the breaker and air started circulating.
Read less
Was this helpful?
Thank you for voting!
freezer became frosty but refrigerator's camera didn'thave any coll at all.
1 person
found this instruction helpful.
-
Yakov from BROOKLYN, NY
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
After describing my problem PartSelect consultant emmidiately diagnost the problem and I ordered Evaporator Fan Motor. Along with purches order confirmation I got video how to install a new motor.
The hardest part was to connectthe ground wire becase space in that area was verylimited. Otherwise it was just like a walk in the park. ... Read more r />As soon as I installed motor and turned on the refrigirator, everything start working properly.
Thank you PartSelect, you sved me hundreds of dollars.
The hardest part was to connectthe ground wire becase space in that area was verylimited. Otherwise it was just like a walk in the park. ... Read more r />As soon as I installed motor and turned on the refrigirator, everything start working properly.
Thank you PartSelect, you sved me hundreds of dollars.
Read less
Was this helpful?
Thank you for voting!
Installed Ice Maker in Freezer
1 person
found this instruction helpful.
-
Chris from SACRAMENTO, CA
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Installed ice machine components using kit and included instructions. Easy! Ran a copper line from under sink valve to back of refrigerator under the floor. Drilled two holes to run copper line. Plumber turned water off and replaced single valve with a double valve (one line to faucet and the other for the copper line). Installed shut of
... Read more
f valve and filter at the other end of copper line. Then stainless hose to refrigerator. Everything went smooth. Double check the factory installed plastic line from the electric valve to the inlet for your freezer. Mine was barely inserted and leaked. I pushed it in all the way and it is fine now... Ice maker works really well! Wish I had done this sooner!
Read less
Was this helpful?
Thank you for voting!
Light switch broke off
1 of 2 people
found this instruction helpful.
-
Kathy from TEMECULA, CA
- Very Easy
- Less than 15 mins
-
Pliers
We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing
Was this helpful?
Thank you for voting!
light did not work on the refrigerator side
1 of 2 people
found this instruction helpful.
-
David from GROVESPRING, MO
- Easy
- Less than 15 mins
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what i
... Read more
s inside the refer!
Read less
Was this helpful?
Thank you for voting!
Rocker on switch broke off
1 of 2 people
found this instruction helpful.
-
David Barnes from ROSWELL, NM
- Very Easy
- Less than 15 mins
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
Was this helpful?
Thank you for voting!
Doesn’t cool
1 of 3 people
found this instruction helpful.
-
Benjamin from WASCO, CA
- Very Easy
- Less than 15 mins
-
Screw drivers
Work just perfect
Was this helpful?
Thank you for voting!
I broke the cooling fan while cleaning the heat exchange area
1 of 3 people
found this instruction helpful.
-
Daniel from N TONAWANDA, NY
- Really Easy
- 15 - 30 mins
Very simple, pulled old fan blade off and pushed new fan blade onto shaft. Perfect fit!
Was this helpful?
Thank you for voting!
you have to turn it off and on to run.
0 of 1 people
found this instruction helpful.
-
chris from woodland hills, CA
- Really Easy
- Less than 15 mins
-
Nutdriver
Just like the video showed me.It still does not work. Have to turn it off and on to make it start up.I also replaced thermostat in freezer. Does not work.
Was this helpful?
Thank you for voting!