My Orders
ARG7302 Amana Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Gas oven would not light
1 person
found this instruction helpful.
-
Elizabeth from Vernon, CT
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I have an older model gas oven which required that all screws had to be removed. With a screw gun the job would not haven taken long. Once the bottom pan was removed the oven ignitor took some finese to remove. This was only due to the short wires. Once pulled sufficiently to be able to disconnect the ignitior (although I was afraid I
... Read more
was going to pull the wires and separate them from the stove), it was very simple to unplug and plug in the new one (again, making sure to hold the plug so the wires would not retract back behind the wall which would have required the stove to be pulled out from the wall and the back disassembled).
The good news, it was a success and the oven works like new. Roughly $38.00 later, I am back cooking. The extra effort for the screws was offset by being able to complete this by myself and saving the cost of a repair man. Would do it again.
The good news, it was a success and the oven works like new. Roughly $38.00 later, I am back cooking. The extra effort for the screws was offset by being able to complete this by myself and saving the cost of a repair man. Would do it again.
Read less
Was this helpful?
Thank you for voting!
Gas oven would not heat up
1 person
found this instruction helpful.
-
John from Blairsville, GA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
My repairman told me it was probably the ignitor (even though the old one sitll glowed), but after weeks of waiting for his back-ordered part, I decided to try it myself - found it on PartSelect and had it 3 days later. Turned off the power to the oven. Slid out the 2 racks, and the cover below the racks. Unscrewed 1 nut and removed th
... Read more
e V shaped metal plate that distributes the heat. Under that removed 3 screws that hold the ignitor clip in place and got the igniter out of the clip. I couldn't get to the plug on the other end of the ignitor until I took out the oven drawer and removed 2 screws holding a metal cover in place below the oven. Reversed the whole process being careful with the end of the new ignitor (I read it was fragile). The oven now heats up in 5 minutes and maintains temperature again!
Read less
Was this helpful?
Thank you for voting!
Range oven door switch need replaced
1 person
found this instruction helpful.
-
Ruth from Gastonia, NC
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
I raised the top of my Whirlpool Continuous Cleaning Canning Oven, then had to unscrew 3 screws and a lock nut, then raise top about 4 inches, so I could put my hand inside to unplug the wires to the switch, and push it through the hole in front, of oven. Then put the new switch through hole and plug in new switch. Then screw down top;
... Read more
and close lid. Part #866294
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat
1 person
found this instruction helpful.
-
Timothy from Madison, AL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
WEB research indicated that even though ignitor would glow, that it was likely faulty.
Turned off power at circuit breaker
Remove shelves and bottom plate from inside oven.
Unscrew deflector plate
Remove drawer under stove
Remove ignitor and unplug from connector
replace ignitor, plug in, reassemble stove. ... Read more r />Needed flashlight to see under stove.
Turned off power at circuit breaker
Remove shelves and bottom plate from inside oven.
Unscrew deflector plate
Remove drawer under stove
Remove ignitor and unplug from connector
replace ignitor, plug in, reassemble stove. ... Read more r />Needed flashlight to see under stove.
Read less
Was this helpful?
Thank you for voting!
The Oven would not turn on reliably
1 person
found this instruction helpful.
-
Carlos from Grand Rapids, MI
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Remove the racks
remove one nut that holds the heat deflector
3 screws that hold the igniter
remove the drawer
remove 2 screws holding a heat shield in place.
unplug old igniter and reinstall
remove one nut that holds the heat deflector
3 screws that hold the igniter
remove the drawer
remove 2 screws holding a heat shield in place.
unplug old igniter and reinstall
Was this helpful?
Thank you for voting!
no spark
1 person
found this instruction helpful.
-
Richard from ROLLING MDWS, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers
I used your instructions
Was this helpful?
Thank you for voting!
Oven would not light
1 person
found this instruction helpful.
-
Verno from PRINCETON, WI
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I had done this before, but a while back, so it took a little longer to disassemble and find the igniter. Once there, easy to troubleshoot with a meter. Reassembly was only a few minutes and part of that was finding a new nut, since I lost one. I had to remove the storage drawer, then remove a metal cover to get at the connections. I te
... Read more
sted the power to the igniter and found it to be OK. I tested continuity and had some but very low. Pulled the diffuser and cover off burner to locate igniter. Ordered part,put it on and reassembled everything. Working fine.
Read less
Was this helpful?
Thank you for voting!
Gas valve would not open to let the gas flow to burner.
1 person
found this instruction helpful.
-
Matt from Billerica, MA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Simple install - 6 -7 screws one nut. Once replaced oven worked good as new. Part shipped from PartSelect actually better than one installed by repairman 4 years ago - fit like an original part.
Thanks PartSelect.com
Thanks PartSelect.com
Was this helpful?
Thank you for voting!
Old caps were cracked, and discolered
1 person
found this instruction helpful.
-
James from Des Moines, IA
- Really Easy
- 15 - 30 mins
-
Screw drivers
1. removed the screws that held the caps.
2. Moved the stove away from the wall.
3. Unplugged the power cord, for safety.
4. Removed the caps.
5. Install the new caps.
6. Plug the power cord in.
7. Place stove back in positon against the wall.
2. Moved the stove away from the wall.
3. Unplugged the power cord, for safety.
4. Removed the caps.
5. Install the new caps.
6. Plug the power cord in.
7. Place stove back in positon against the wall.
Other Parts Used:
Was this helpful?
Thank you for voting!
oven very slow to light
1 person
found this instruction helpful.
-
Larry from Circleville, OH
- Really Easy
- 15 - 30 mins
-
Screw drivers
First I had to take the drawer completely out of the stove to reach the igniter. I then removed the screws that held the igniter in place and removed it. I had to slightly modify the replacement part by squeezing it together to make it fit into the same space. I put the replacement igniter in place and screwed it down; put the drawer b
... Read more
ack in the stove and turned on the over to see if it would light. Bingo, job done!
Read less
Was this helpful?
Thank you for voting!
oven died
1 person
found this instruction helpful.
-
Ben from Lawrenceville, GA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set, Wrench set
looked at and saw that ignitor was cracked,saw simple repair ahead. just needed the right part . Without part , select simple ,and easy selection, i might not have ever found the right part. as i said before finding the right part is 90 percent of the job and they made that an easy task .
of course if you want me to describe ... Read more in detail, took out the pan saw the bad ignitor, removed 2 serews, disconnected 2 wire, the reassembled in the opposite direction. 30 minutes tops. I am sure this saved me at least 150 bucks for some "so called reparman" to do the same job, Most people do not realise that they have more education than most of these "repairmen". The only advantage these "repair people" have is acess to schematics and part numbers. Part select is a good start on putting this information in the hands of us average "idiots" as I am sure the repair folks call us when we pay 200 bucks for a 30 dollar job.
of course if you want me to describe ... Read more in detail, took out the pan saw the bad ignitor, removed 2 serews, disconnected 2 wire, the reassembled in the opposite direction. 30 minutes tops. I am sure this saved me at least 150 bucks for some "so called reparman" to do the same job, Most people do not realise that they have more education than most of these "repairmen". The only advantage these "repair people" have is acess to schematics and part numbers. Part select is a good start on putting this information in the hands of us average "idiots" as I am sure the repair folks call us when we pay 200 bucks for a 30 dollar job.
Read less
Was this helpful?
Thank you for voting!
Range top worked; broiler worked; oven would not heat.
1 person
found this instruction helpful.
-
Philip from W. Bridgewater, MA
- Easy
- 15 - 30 mins
Disconect power source; Remove oven racks, remove storage drawer under oven; remove floor of oven, remove flame deflector, remove three screws holding igniter cage and unplug faulty igniter. Reverse all steps for reassembly.
Was this helpful?
Thank you for voting!
An unexplained failure of the unit, the main PCB/ controller
2 of 4 people
found this instruction helpful.
-
lance from loranger, LA
- Easy
- 15 - 30 mins
-
Nutdriver
After a standard trouble shoot, and finding the control PCB has the correct line voltage and the unit failure has more than one function failure with-in the unit operation, I replaced the Control PCB.
Removal and install took about 10 min, and the unit works fine, all automation is working properly.
Lance
Removal and install took about 10 min, and the unit works fine, all automation is working properly.
Lance
Was this helpful?
Thank you for voting!
All four Spark did not ignite or only once and a while
1 of 2 people
found this instruction helpful.
-
Dale from Monmouth Junction, NJ
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Unplugged the stove, removed all 4 burner discs from the stove top (2 screws each- WATCH YOU DONT STRIP HEADS) and disconnecting electrode wires ( DONT HAVE TO- IF YOU HAVE ENOUGH ROOM TO SIDE TOP UNIT OVER), unscrewed the old module, removed each of the 6 wires,one at a time and connected wires to the new module. Plug in stove to test be
... Read more
fore you screwed it into place, reinstalled the top unit , put the stove top in place,. Done!
Read less
Was this helpful?
Thank you for voting!
oven took long time to light
1 of 2 people
found this instruction helpful.
-
joseph.k from pottsville, PA
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
shut off gas at tank, pulled stove out from counter area to gain acess to back, removed oven door removed removed screws holding igniter unit in place, i then removed the stove rear panel to get at the wiring for ignitor,remoded old part returned to front and installed new part, checked voltage then re-connected new wires, turded gas back
... Read more
on and tested oven, oven came on less than a minute, put rear panel on stove put door back on and put stove back into counter area, stove works like new.
Read less
Was this helpful?
Thank you for voting!